Sealey YK15.V3 Instructions

FLOOR Models: YK15.V3, YK15FM.V3, YK30.V3, YK30FM.V3, YK50FM.V3.
BENCH Models: YK10BM.V3, YK15BM.V3.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY
 Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
 Maintain the press in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Keep the press clean for best and safest performance.
 Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensure
there is adequate lighting.
 Ensure the workpiece is correctly secured before operating the press.
 WARNING! Always wear approved eye or face protection when operating the press.
 Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.
 Keep hands and body clear of the work table when operating the press.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury.
 DO NOT force the press to achieve a task it was not designed to perform.
 DO NOT adjust or tamper with the safety valve.
 DO NOT exceed the rated capacity of the press.
 DO NOT apply off centre loads.
 DO NOT allow the workpiece or the arbor plates to fall from the press working bench.
 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
 DO NOT operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
 WARNING! When moving the table position please observe safe handling practices.
 WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be
placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
 DANGER! The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam, or
lift direct with a forklift with the forks located under the top crossbeam. DO NOT use a pallet truck.
2. INTRODUCTION & SPECIFICATIONS
2.1 GENERAL INFORMATION
The Sealey range of heavy duty floor and bench hydraulic presses are ideal for a variety of workshop applications and are particularly suited
to agricultural or industrial use. Jobs such as straightening, bending, folding, punching, removing bolts and bearings etc are some of tasks that
may be accomplished by your press. All models are fitted with pressure gauge and work-table V-blocks except where stated. The "BM" and "FM"
range of press units feature integrally mounted rams giving more vertical clearance between the table and ram head enabling larger items
to be fitted on the working table.
 WARNING! All models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece is secured on table and loads that flex will not suddenly "give" causing danger to operator or damage to component.
Model: YK10BM.V3
capacity 10T
Ram Stroke 135mm
Extension Screw n/a
Max Ht-Ram to Table 460mm
Min Ht-Ram to Table 160mm
Table Aperture 140mm
Work Table Depth 155mm
Work Table Width 500mm
overall Height 1125mm
Gauge Included yes
Weight 71kg
3. ASSEMBLY & INSTALLATION
Unpack product and check contents against list below. Should there be any damaged or missing parts contact your supplier immediately.
Take care to ensure safety when removing main frame from packing as the unit is very heavy. Retain pressure gauge in carton until required,
and do not remove white tape from gauge mount or masking tape from the angle arm.
Contents:
Frame Legs x2 Worktable x1 Worktable pins x2 V-blocks x2 Pump handle x1 Pressure gauge + Adaptor x1
Gauge angle arm connector x1 Winch Handle (50ton models only).
YK15BM.V3 YK15.V3 YK15FM.V3
15T 15T
95mm 150mm
75mm 75mm
450mm 660mm 660mm
150mm 150mm 150mm
140mm 140mm 140mm
155mm 155mm 155mm
500mm 500mm 500mm
1050mm 1775mm 1750mm
yes yes
74kg 81kg
YK10BM.V3, YK15.V3, YK15BM.V3, YK15FM.V3, YK30.V3, YK30FM.V3, YK50FM.V3
InSTRUcTIonS FoR:
HYDRAULIC BENCH & FLOOR PRESS
YK30.V3 YK30FM.V3
15T 30T 30T
95mm 150mm 120mm
75mm 75mm 75mm
680mm 690mm
150mm 155mm
170mm 170mm
190mm 190mm
550mm 550mm
1850mm 1915mm
yes yes yes
86kg 158kg 135kg
YK50FM.V3
50T
120mm
75mm
715mm
155mm
170mm
190mm
550mm
1910mm
yes
214kg
Issue no: 1 - 02/12/08