Sealey PB1000.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Ensure that the pulley block is in sound condition and good working order.

Take action for immediate repair or replacement of damaged parts.
Use recommended parts only. The use of unauthorised parts may be

dangerous and will invalidate the warrentry.
Ensure the support for the pulley block is capable of withstanding a load of

at least 1½ times the safe working load of the block.
Keep the pulley block clean for the best and safest performance.

Locate the pulley block in a suitable, well-lit area.

Keep work area clean and tidy and free from unrelated materials.

Ensure all non-essential persons keep a safe distance whilst the pulley

block is in use.
Ensure load slings are fully engaged in the load hook and that the hook

safety bar is in the closed position.
Raise and lower a load on the pulley in a smooth, controlled manner. DO

NOT shock load the pulley block by allowing the attached load to fall freely,
even for very short distances.
DANGER: Use the pulley block for lifting only, NOT for suspending the lifted

load.
Use a qualified person to lubricate and maintain the pulley block.

DO NOT operate the pulley block if it is damaged.

DO NOT allow untrained persons to operate the pulley block.

DO NOT exceed the rated capacity (working load) of the pulley block. (See

Section 5).
DO NOT raise or lower the load with jerky or abrupt movements of the rope.

DO NOT attempt to lift a load if the load rope is kinked or knotted.

DO NOT try to raise a load with two, or more, pulley blocks - use a single

block of adequate capacity.
DO NOT use the pulley block to drag the load across the floor. Always

position the load directly below the block.
DO NOT wrap the load rope around the load - always use separate,

suitable, ropes or slings of the correct capacity.
DO NOT allow anyone to stand, or pass beneath, the raised load.

DO NOT use the pulley block for purposes other than that for which it is

intended.
Store the pulley block in a dry, childproof area when not in use.

IMPORTANT: Use only with wire rope of the specified diameter.
DO NOT attempt to free a jammed rope or pulley while a load is attached.
Use alternative means to support the load and unhook the rope from the
load before rectifying the jam.
BEWARE! Broken rope strands or unfinished rope ends present risk of
personal injury, i.e. a puncture wound.
Fig.1
© Jack Sealey Limited
INSTRUCTIONS FOR:
PULLEY BLOCKS
PB1000.V2, PB2000.V2
MODEL Nos:
2. SPECIFICATION
Working Rope
load Ø
mm
kg
1000
Ø7
2000
Ø13
* Ambient operating temperature range: -10°C to +50°C.
3. OPERATION
IMPORTANT: Before using the pulley block ensure that you have read,
understood and applied the safety instructions in Section 1.
NOTE: This pulley block will normally be used in conjunction with a
mechanical pulling device and should never be operated by hand. Wear safety
gloves and keep hands away from moving pulley wheels.
3.1. Rotate the hook through 90° as shown in fig.1A to release the hinge plate.
Move the hinge plate upwards as shown in fig.1B and place the rope into
the pulley groove. Close the hinge plate and rotate the hook through 90° to
lock it. DO NOT attempt to use the pulley block with the hinge plate open.
3.2. If using the pulley block for simple lifting as shown in fig.3A ensure that it is
suspended from a structure capable of supporting at least 1½ times the safe
working load of the block.
3.3. Ensure that the block hook is fully engaged with the safety bar closed.
Confirm that the total load does not exceed the working load of the block.
See Section 4.
3.4. Ensure that the lifting rope is securely and safely attached to the load and
that the load is directly below the block.
3.5. Take up the tension in the rope until the load rope is taut and not pulling at
an angle.
3.6. Start to raise the load and ensure that it is level, with no possibility of the
load tilting and/or slipping from its restraints. If necessary, lower the load
and readjust the attachment point to obtain a safe, level lift.
NOTE: DO NOT suddenly release the pulley rope, as the pulley has no braking
system attached to it.
3.7. Continue to raise the load to the required height in a slow, controlled
manner. DO NOT raise the load so far that the hook comes into contact with
the block.
3.8. Lower the load slowly and smoothly, avoiding jerky or abrupt movements.
3.9. If, at any time, the rope will not move in either direction do not attempt to
force it but, after arranging safe support for any suspended load, have the
block inspected by an Authorised Service Agent.
Original Language Version
Net D1
weight B B1 B2 C Ø
kg
3.3 118 76 17 23 85
8.9 199 92 24 27 150
PB1000.V2, PB1500.V2
Fig.2
D2
Ø L L1 L2 R
105 305 200 23 4
190 425 263 30 7
Issue: 3(L) - 15/05//17