Sealey TA120 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Only suitable for automotive circuits. NOT suitable for 110-230V applications.
‰
9 9 Observe standard workshop safety procedures when using.
9
9
WARNING! The Fuse blade may become hot during testing. Allow to cool before removing.
‰
WARNING! DO NOT exceed Maximum Load: 20A/48V for Max 10sec.
‰
9 9 Ensure vehicles ignition, is switched OFF, before connecting or disconnecting tester.
9
9
9 9 Keep the work area clean, uncluttered and ensure there is adequate lighting.9Keep tools and other items away from the engine, and
9
9
ensure you can see the battery and working parts of engine clearly.
9 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery. Contain or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
9 9 DO NOT disassemble. Tester must be checked by qualified service personnel only.
9 8
9 9 DO NOT get wet or use in damp or wet locations or areas where there is condensation.
9 8
9 9 DO NOT use for any purpose other than for which it is designed.
9 8
DO NOT pull by the cables to free from the fuse terminals.
8
9 9 DO NOT operate if damaged.
9 8
When not in use store in a safe, dry, childproof location.
9
WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied
by the operator.
2. INTRODUCTION
Fast, accurate and safe current measurement at the fuse box. Ideal for fault-finding on car and commercial vehicle electrical circuits. Features large
LCD display. Plugs straight into the vehicle's fuse board.
3. SPECIFICATION
Model no's: ........................................................TA120/TA121
Range: ............................................................. 0-20A - 0-48V
Accuracy: ........................................................................ ±2%
Fuse: ................................................................ Standard/Mini
4. OPERATION
4.1. Measuring
4.1.1. With the vehicle ignition OFF, remove the fuse from the circuit to be tested
and insert it into the fuse jack (fig.1.2), this ensures the correct level of
circuit protection.
4.1.2. Insert the plug into the vehicle fuse socket.
4.1.3. Switch on the vehicle ignition if required, to energise the circuit and then switch
on the tester fig.1.5.
4.1.4. Operate the circuit under test and the LCD will display the measured current.
WARNING! The Fuse blade may become hot during testing. Allow to cool
‰
before touching.
© Jack Sealey Limited
INSTRUCTIONS FOR
CURRENT TESTER 20A
TA120 STANDARD FUSE
MODEL NO'S:
TA121 MINI FUSE
Original Language Version
TA120
1
1. Standard Blade Type
2. Fuse Jack
3. Lead
4. LCD Display
2 5. Power ON / OFF
4
3
TA121
1
1. Mini Blade Type
2. Fuse Jack
3. Lead
2
4. LCD Display
5. Power ON / OFF
4
3
TA120, TA121 | Issue:4(3) 20/0318
fig.1
5
5