Sealey RE83/840.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Only fully trained and qualified persons should use this equipment. These instructions are not a substitute for user receiving full
supervised training by a qualified person. It is important the user understands the applications, limitations and potential hazards
of the product.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
Familiarise yourself with product application and limitations, as well as the specific hazards peculiar to the pump.
9
WARNING! Disconnect the hydraulic pump from the apparatus before servicing or performing any maintenance.
‰
maintain pump in good order. Replace/repair with genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use qualified person to lubricate and maintain the hydraulic pump. DO NOT use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil
9
only.
Keep the pump and treadle clean for best and safest performance.
9
WARNING! Ensure you know how much load you are pushing. Never exceed the maximum pushing capacity.
‰
The kit accessories may be used with other popular makes of kit.
9
We recommend the use of BS approved safety impact goggles and heavy duty gloves when working with this pump. Both are available from
9
your authorised Sealey stockist.
maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
If working on an 'off centre' load, pump with care. If you feel undue resistance, stop and re-adjust the set-up.
9
Ensure any hydraulic hoses are not bent or kinked but laid out correctly. Avoid damage to hoses (e.g. crushing/cutting).
9
Keep non-essential persons away from the operating area. Be aware of the locations of other persons assisting you.
9
DO NOT operate the pump if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WARNING! DO NOT use for any purpose other than for which it is designed.
‰
When not in use, place dust cap in end of hydraulic hose or cylinder and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Suitable for use with SuperSnap® hydraulic ram as supplied with model no. DZRE92/C Body Straightener and all body kits. Supplied without air
hose. (Also available with hose - Order model No. RE83/840/CWH.
3. SPECIFICATION
model no. .......................... RE83/840.V2/RE83/840/CWH.V2
max. air input ......................................................... 90-120psi
Oil capacity .................................................................. 450cc
Oil pressure ..............................................................10000psi
4. OPERATION
4.1. SETTING UP
4.1.1. Remove pipe plug from hydraulic adaptor and connect a hose
(model RE83/840.V2 only)
4.1.2. Remove the shipping plug from the air inlet port and insert a
1/4" NPT quick release coupler (If not fitted).
4.1.3. Connect an air supply to the quick release air hose coupler and
connect the hydraulic hose to the ram or device coupler.
4.1.4. To operate the pump for ram/device extension/actuation, depress the
treadle at the air inlet valve end.
4.1.5. To retract the ram/device to the original start position, depress treadle
end marked "RELEASE". Retraction will stop with load held, when
pressure on treadle is removed. For fullest retraction continue to
depress.
© Jack Sealey Limited
AIR HYDRAULIC PUMP 10TONNE/WITH HOSE
mODEL NO'S:
Wear protective
gloves
Original Language Version
RE83/840.V2, RE83/840/CWH.V2
S
RE83/840.V2, RE83/840/CWH.V2 | Issue:3 (H,F) 25/06/19
mODEL: RE83/840.V2
mODEL: RE83/840/CWH.V2