Sealey Power Products CD2000 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 ELECTRICAL SAFETY. F
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation
of appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD
together with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional
electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand
the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested
by a qualified person at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. DO ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. above and use a Portable Appliance Tester (PAT).
1.1.4. DO ensure that cables are always protected against short circuit and overload.
1.1.5. DO regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power
connections to ensure that none are loose.
1.1.6. DO check that the voltage marked on the product is the same as the electrical power supply to be used, and check that all fused
plugs are fitted with the correct capacity fuse.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace
or repair by qualified persons. A U.K. 3 pin plug with ASTA/BS approval
is fitted. In case of damage, cut off and fit a new plug according to the following
instructions (UK only - see diagram at right).
a) Ensure the unit is correctly earthed via a three-pin plug.
b) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
c) Connect the BROWN live wire to live terminal ‘L’.
d) Connect the BLUE neutral wire to the neutral terminal ‘N’.
1.2 GENERAL SAFETY
! Disconnect the heater from the mains power before handling or cleaning.
! Maintain the heater in good order and clean condition for best and safest performance.
! Replace or repair damaged parts. Use recommended parts and an authorised service agent. Non authorised parts may be dangerous
and will invalidate the warranty.
! Locate the heater in an adequate working area for its function, keep the immediate area in front of the outlet grill clean and tidy and free
` from unrelated materials.
! Only use the heater standing on its feet in the upright position.
% DO NOT allow the heater to get wet as this may cause an electric shock, and will damage the heater.
% DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in heater hot air flow, or run under a carpet.
% DO NOT cover heater when in use, and do not obstruct the air inlet and outlet grill (i.e. clothing, curtain, furniture, bedding etc).
% DO NOT use heater on very deep pile carpets.
% DO NOT use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.
% DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock, fire or damage to heater.
% DO NOT use the heater out of doors. This heater is designed for indoor use only.
% DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater is not working correctly, or if the heater has been
dropped or has become wet.
% DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat sensitive
materials may be stored.
% DO NOT place the heater near items that may be damaged by heat.
% DO NOT touch the outlet grill (top) of the heater during and immediately after use as it will be hot.
% DO NOT allow children to touch or to operate the heater.
% DO NOT place heater too close to yourself, allow the air to circulate.
% DO NOT use the heater for any purpose other than for which it is designed.
! Allow the unit to cool before storage. When not in use, disconnect from the mains and store in a safe, cool, dry, child proof area.
p
 WARNING! It is the user’s responsibility to check the following:
p
INSTRUCTIONS FOR:
CONVECTOR HEATERS
CD2000 & CD2502
Model No:
Yellow & Green
Earth wire
Blue
Neutral
wire
Brown Live
wire
13 amp
3 pin
plug
CD2000 & CD2502-080698