Advertisement
Quick Links
Special Vehicle Series :
Wheel Loader
Tools
Scissors
Ruler, set square
Glue (Wood glue or craft glue recommend)
Exhausted ballpoint pen (out of ink)
Toothpicks (for use in applying glue)
Tweezers (useful for handling small parts)
Pencil
Pattern
Dotted line
Dashed and
dotted line
Solid line
Solid red line
Diagonal
grey lines
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Assembly Instructions: Seven A4 sheets (No. 1 to No. 7)
Build this model with careful reference to the Assembly Instructions.
01
Key to symbols
Mountain fold
Fold so that the printed
pattern faces outside.
Valley fold
Fold so that the printed
pattern faces inside.
Cut parts out
along this line.
Cut a notch
along this line.
Cut these areas
out.
Assembly
Instructions
* This model was designed for Papercraft and
may differ from the original in some respects.
Assembly tip
Write the number of each part on the reverse side of the part in pencil
upon cutting it out, to be sure you can tell which part is which later.
Before gluing, crease the paper along
mountain and valley fold lines. Trace along
the folds with a ruler and an exhausted
ballpoint pen (out of ink) to get a sharper fold.
Make sure rounded sections are nice and stiff.
The dots show where to glue
the pieces together. Glue the
pieces together as shown in the
following examples.
Some parts must be glued
together along the cut surfaces.
Red dot
Glue parts with the same
number together.
(Numbers are
not printed on very small parts.)
Green dot
Glue areas within the same
part together.
Blue dot
Glue to the reverse side of the
specified part.
h t t p : / / w w w. c a n o n . c o m / c - p a r k / e n /
View of completed model
Assembly instructions
Red arrow
Blue arrow
Light blue
Light grey
Glue
Insert
(without gluing)
Glue tab
Reverse side of
paper
Movable part
This denotes a part
that must be able to
move after the model
is completed. Be sure
to crease these parts
sufficiently.
Advertisement
Related Manuals for Canon Paper Craft Special Vehicle 01 Series
Summary of Contents for Canon Paper Craft Special Vehicle 01 Series
- Page 1 Special Vehicle Series : Wheel Loader Assembly Instructions h t t p : / / w w w. c a n o n . c o m / c - p a r k / e n / View of completed model * This model was designed for Papercraft and may differ from the original in some respects.
- Page 2 Wheel Loader Assembly Instructions Assemble the cab. Use care to get the shape right Glue flaps a and b in order. when assembling this part, Cross section referring to the cross section at right. Close this surface last and glue it in place. Glue flaps a, b, and c in order.
- Page 3 Wheel Loader Assembly Instructions Shape this part before gluing it. Leave an opening here. Glue flaps a, b, c, d, and e in order. This is a moving part. Do not glue it. Fold the left and right flaps back and glue each in place. Glue flaps a, b, and c in order.
- Page 4 Wheel Loader Assembly Instructions Glue flaps a and b in order. Insert into the opening in part F. Cross section Referring to the cross section, insert this part through the holes and fix it in position at top and bottom. Overhead view Assemble in the same way as part 31.
- Page 5 Wheel Loader Assembly Instructions...
- Page 6 Wheel Loader Assembly Instructions Assemble the left wheels. Assemble the right wheels in the same way. (The left and right tires have different tread directions.) Cross section Cross section Insert the axles into the body of the wheel loader and glue the wheels in place, checking the direction of the tread on the tires and taking care to attach the left and right tires on their proper sides.
- Page 7 Wheel Loader Assembly Instructions Apply glue to the cut surface of the paper and glue this part to the body of the wheel loader, On parts with no glue tabs, concealing the glue tabs. apply glue to the cut surface of the paper. Fold the shaft part in and glue these parts together.