Sealey AK7062 Instructions

Part No Description
AK7062.01. . . . . . . . . . . . . . . . . . . Staples (4mm x 13mm). . . . . . . . . . . . . . . . . . . . . . 1000pcs/box
AK7062.02. . . . . . . . . . . . . . . . . . . Staples (9.4mm x 8mm) . . . . . . . . . . . . . . . . . . . . . 1000pcs/box
AK7062.03. . . . . . . . . . . . . . . . . . . Headed Nail (12mm) . . . . . . . . . . . . . . . . . . . . . . . . 1000pcs/box
AK7062.04. . . . . . . . . . . . . . . . . . . Needle Nail (15mm) . . . . . . . . . . . . . . . . . . . . . . . . 1000pcs/box
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Issue : 3
Issue Date: 100305
Qty
01284 757500 www.sealey.co.uk
Web
sales@sealey.co.uk
01284 703534
email
AK7062 Issue: 2 - 23/10/09
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY.  WARNING! It is the user's responsibility to read, understand and comply as
follows. You must check all electrical equipment and appliances to ensure they are safe before using.
You must inspect power supply leads, plugs and all electrical connections for wear and damage. You
must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly
important to use an RCD together with portable products that are plugged into an electrical supply not
protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer. You must also read and understand the following instructions
concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business
premises, to be tested by a qualified Electrician at least once a year by using a Portable Appliance Tester
(PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe
condition of the appliance, and the safety of the appliance operator. If in doubt about electrical safety,
contact a qualified Electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be
used, and that plugs are fitted with the correct capacity fuse. A 13Amp plug may require a fuse smaller
than 13 Amps for certain products (subject to 1.1.10. below) see fuse rating below.
1.1.7. DO NOT pull or carry the powered appliance by its power supply
lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged leads, plugs or connections.
Immediately replace or have repaired by a qualified Electrician.
A U.K. 3 pin plug with ASTA/BS approval is fitted. In case
of damage, cut off and fit a new plug according to the following
instructions (discard old plug safely). (UK only - see diagram at
right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal 'E'.
b) Connect the brown live wire to live terminal 'L'.
c) Connect the blue neutral wire to the neutral terminal 'N'.
After wiring, check there are no bare wires, that all wires
have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN)
and neutral (BLUE) wires only. Double insulated products are
always marked with this symbol . Check you model carefully
to see which type of product your have. To re-wire, a double
insulated item, connect the brown and blue wires as indicated above. DO NOT connect brown or blue to
the earth terminal.
1.1.10. Cable extension reels. When a cable extension reel is used it should be fully unwound before
connection. A cable reel with an RCD fitted is recommended since any product which is plugged into the
cable reel will be protected. The section of the cable on the cable reel is important. We recommend
that at least 1.5mm² section cable but to be absolutely sure that the capacity of the cable reel is suitable
for this product and for others that may be used in the other output sockets, we recommend the use of
2.5mm² section cable.
Original Language Version
INSTRUCTIONS FOR:
ELECTRIC 4 IN 1 STAPLER & NAILER
AK7062
MODEL No:
Yellow & Green
Earth wire
Blue
Neutral
wire
Brown
Live
wire
wire
restraint
FUSE RATING
THIS PRODUCT MUST BE
FITTED WITH A:
5 Amp FUSE
AK7062 Issue: 2 - 23/10/09