Sealey PDME160B Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
It is the responsibility of the owner and the operator to read, understand and comply with the following:
p
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
also read and understand the following instructions concerning electrical safety.
1.1.1 The
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The
and the safety of the appliance operators.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1 and 1.1.2
and use a Portable Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6 Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7 pull or carry the appliance by the power cable.
1.1.8 pull the plug from the socket by the cable.
1.1.9 use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and
Fit a new plug according to the following instructions (UK only).
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above -
1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
p
3 Maintain the drill in good condition (use an authorised service agent).
p
3 Check alignment of moving parts and check for possible broken parts.
3 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
3 Ensure the set screws of the head frame are screwed tight before using the drill.
3 Secure the drill to the bench/floor to avoid it tipping, sliding or walking.
3 Drill is designed for use with drill bits only.
3 Ensure the chuck is securely fastened to the spindle.
3 Remove adjusting keys, chuck key and wrenches from the machine and working area before switching on.
3 Use clamps or a vice (not included, but available from your Sealey dealer) to secure the workpiece.
workpiece by hand.
3 Refer to speed chart for recommended drilling speeds.
p
p
3 Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
3 Keep the work area as childproof as possible by using padlocks and master switches.
3 Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
MODEL NO:
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
makes owners of electrical appliances responsible for the safe condition of those appliances
connect either wire to the earth terminal.
INSTRUCTIONS FOR:
Blue
Neutral
Wire
, are fitted with live (brown) and neutral (blue) wires only.
Yellow & Green
Earth Wire
Brown
Live
Wire
Cable
Restraint
attempt to hold the
PDME160B-PDME200F - 1 - 151204