Sealey LED112.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. ELECTRICAL

WARNING! It is the user's responsibility to read, understand and comply with the following:

WARNING! THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads
and all electrical connections for wear and damage.

You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.

You must also read and understand the following instructions concerning electrical safety.

Ensure the light is connected to an appropriate electrical on/off switch.

Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.

Ensure that cables are always protected against short circuit and overload.

Regularly inspect power supply, leads and all electrical connections for wear and damage, especially power connections, to ensure
that none are loose.

Ensure the voltage marked on the product is the same as the electrical power supply to be used.

DO NOT pull power cable once installed.

DO NOT use worn or damaged leads, or connections. Immediately replace or have repaired by a qualifi ed Electrician.

Ensure the unit is correctly earthed and wired according to the following. (Installation should be undertaken by a qualifi ed electrician)
a) Connect the green/yellow earth wire to the earth terminal 'E'.
b) Connect the brown live wire to live terminal 'L'.
c) Connect the blue neutral wire to the neutral terminal 'N'.

After wiring, check there are no bare wires, that all wires have been correctly connected.
1.2. GENERAL SAFETY

WARNING! Turn off the mains power supply before servicing or performing any maintenance.

Maintain the light in good condition (Repairs must only be undertaken by a qualifi ed electrician).

Replace or repair damaged parts. Use genuine parts only, non authorised parts may be dangerous and will invalidate the warranty.

Ensure the light is installed correctly in accordance with these instructions.

Only install the light on a vertical surface.

DO NOT fi x the light on any horizontal surface i.e. ceiling, or overhang.

Ideally the Installation should be away from fl ammable or combustible materials such as wood, cloth, paper etc.
▲
DANGER! DO NOT direct the light into a persons eyes. This unit has a very intensive light output, which if incorrectly used could
cause eye damage.

DO NOT install the light where it is likely to be knocked or hit.

DO NOT install in bathrooms, shower rooms, sauna or such locations.

DO NOT install near an exhaust outlet. i.e. boiler fl ue, dryer outlet, etc.

DO NOT use the light without the front glass shield fi tted.
2. INTRODUCTION
Mounted in die-cast powder coated aluminium extra slim housing with wall bracket. SMD LED technology allows ultra-bright illumination whilst
still keeping costs lower than traditional halogen tubes. Even spread of light across a 110° angle. Supplied with power cable at 75cm only and
suitable for outdoor mounting.
3. SPECIFICATION
Model No: .......................................... LED112.V2 ........................... LED113.V2 ............................ LED115.V2
Colour Temperature: .................................. 6500K ...................................6500K ....................................6500K
Dimensions (W x D x H): ........ 157 x 56 x 101mm ................195 x 57 x 152mm .................235 x 57 x 191mm
IP Rating: ..................................................... IP65 ......................................IP65 .......................................IP65
LED Type: ................................................... SMD ..................................... SMD ...................................... SMD
Lumen Output:..........................................1900lm ................................. 5200lm ............................... 10,000lm
PIR Motion Sensor: .........................................No ........................................ No ......................................... No
Power: .......................................................... 20W ......................................50W .....................................100W
Supply: ........................................................ 230V .....................................230V ......................................230V
© Jack Sealey Limited
SMD LED EXTRA SLIM FLOODLIGHT WITH
WALL BRACKET
LED112.V2, LED113.V2, LED115.V2
MODEL NO'S:
Original Language Version LED112.V2, LED113.V2, LED115.V2 Issue 1 23/12/21