Sealey EH5001.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Indoor Use
Refer to
Only
instructions
THIS PRODUCT IS ONLY SUITABLE FOR WELL INSULATED AREAS OR OCCASIONAL USE.
EH5001
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! Electrical installation of the heater to a 3-phase 415volt supply or maintenance must only be carried out
‰
by a qualified electrician.
Make sure the power supply cable is correctly connected to the earth. It is the user's responsibility to read, understand and comply
9
with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
9
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation
of appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. You
must also read and understand the following instructions concerning electrical safety.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
9
electrician, using a Portable Appliance Tester (PAT), at least once a year.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
9
safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
Ensure insulation on all cables and the product itself is safe before connecting to mains power
9
supply.
Ensure that cables are always protected against short circuit and overload.
9
Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
9
especially power connections, to ensure that none are loose.
Important: Ensure the voltage marked on the product is the same as the electrical power supply to
9
be used. A three phase plug must be fitted to this machine.
DO NOT pull the powered appliance by the power cable.
8
DO NOT pull power plugs from sockets by the power cable.
8
DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired
8
by a qualified electrician.
This product must be fitted with a 3-phase plug according to the diagram, and will require a
9
minimum supply of, 16Amps per phase for EH5001 and EH9001, and 32Amps for EH15001.
You must contact a qualified electrician to ensure an appropriately fused supply is available.
Connect GREEN/YELLOW wire to earth (E) terminal.
Connect the live wires to live 1, 2 and 3.
When completed, check that there are no bare wires, that all wires have been connected correctly, that the cable external insulation
extends beyond the cable restraint and that the restraint is tight.
1.2. GENERAL SAFETY
WARNING! The appliance shall be disconnected from its power source during service and when replacing parts and, if the removal
‰
of the plug is foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any
of the points to which they has access that the plug remains removed.
WARNING: DO NOT use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own,
‰
unless constant supervision is provided.
Servicing or maintenance must only be carried out by an authorised service agent.
9
© Jack Sealey Limited
INDUSTRIAL FAN HEATERS:
BTU/HR: 17,000, 31,000, 51,000: OUTPUT 5KW, 9KW, 15KW
EH5001.V2, EH9001.V2, EH15001.V2
MODEL NO:
Do Not
Cover
Original Language Version
EH9001
EH15001.V2, EH9001.V2, EH5001.V2 Issue 1 01/06/23
EH15001