Philips 7100 Instructions

Features
ENGLISH
IMPORTANT
SAFETY
A
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
B
the following:
Read all instructions before using this
appliance.
DANGER
C
To reduce the risk of electric shock:
D
1. Do not reach for a clipper that has fallen into
E
water. Unplug immediately.
2. Use clipper only in dry condition. Do not use
while bathing or in a shower.
3. Do not submerge clipper in water.
F
4. Do not place or store clipper where it can
fall or be pulled into a tub or sink. Do not
G
place in or drop into water or other liquid.
5. Always unplug this clipper from the electrical
outlet immediately after using, except when
clipper is (re)charging.
6. Unplug clipper before cleaning. A Hair Clipping Comb
7. When discarding clipper, unplug clipper to
B Cutting Unit
remove rechargeable battery. See Battery
C Adjustable Wheel Hair Length
Removal instructions.
Setting Selector
8. The batteries used in this device may present
D On/Off Button
a fire or chemical burn hazard if mistreated.
E Turbo Button
Do not disassemble, heat above 100°F
F Charging Light
(212°F) or incinerate.
G Socket for Appliance Plug
WARNING
H Cleaning Brush
I Adaptor
To reduce the risk of burns, fire, electric J Appliance Plug
shock or injury to persons:
K Storage Case
Full Two-Year Warranty
1. Close supervision is necessary when
45-Day Money-Back Guarantee
this appliance is used by, on, or near children
or invalids.
2. Use this clipper for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into water. For assistance visit our
website www.philips.com/norelco or call
1-800-243-3050.
4. Do not rinse or immerse the clipper handle
in water or any other liquid.
5. Keep the clipper, cord and any attachments
away from heated surfaces.
6. Never drop or insert any object into any
opening.
15 mm
14 mm
7. Do not operate, charge or plug in clipper
mm
13
mm
outdoors or where aerosol (spray) products 12
mm
11
are being used or where oxygen is being
administered.
8. Always check cutters, cutting unit and comb
before using the clipper. Do not use the
clipper if cutters, cutting unit or comb are
damaged, as injury may occur.
9. Always attach plug to clipper first, then to
outlet. To disconnect, switch Clipper OFF,
then remove plug from outlet.
10. To prevent possible damage to the cord, do
not wrap cord around the clipper.
11. Use only the cord provided to charge and
(re)charge clipper.
12. Never put clipper in direct sunlight or store
at a temperature above 140°F.
13. This clipper is for use on human hair only.
Do not use this clipper for any other
purpose.
14. Only use the power plug and other
accessories supplied with the clipper.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
1
Registration
Congratulations on your purchase and welcome
to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
Put It To The Test
Like many new products, your Philips Norelco Hair
Clipper may take a little getting used to. If you are
using an electric Clipper for the first time, or if
you've been using a different brand, take the time
H
to acquaint yourself with your new Hair Clipper.
Your Hair Clipper features a double-sharpened
cutting element with reduced friction as well as
I Turbo power to boost cutting speed for a perfect
cut even on the thickest hair.
Throw your scissors away and put your new
J
Hair Clipper to the test. We guarantee precise
results or Philips Norelco will refund you the full
purchase price as long as the request is received
within 45 days of purchase.
To Charge/Recharge
Fully charge Clipper before using for the first
w
time or after non-use for a long period of time.
K
Charging, recharging or using Clipper at
w
temperatures below 40˚F or higher than 95˚F
adversely affects lifespan of the battery.
1 Be certain Clipper is OFF.
2 Insert the appliance plug directly into the
Clipper (fig. 1) and plug the adapter into any
120V AC outlet. Use only the cord provided.
3 The Charging Light on the appliance will
blink green to indicate the Clipper is charging
(fig. 2).
It will take approximately 1 hour to fully
w
charge the Clipper for a cordless clipping
time of up to 120 minutes.
4 When the battery is fully charged, the
charging light lights up green continuously
for 30 minutes and then turns off (fig. 3).
1 2 3
5 Disconnect the cord and unplug from
electrical outlet.
Turbo Power
Simply press the Turbo Button for a turbo
w
power boost for fast results, even on the
4 5 6
thickest hair. The memory function will
remember the last used setting.
Corded Hair Clipping
Clipper does not recharge during corded
w
7 8 9
clipping.
1 Connect cord provided to Clipper (fig. 1) and
plug Clipper into electrical outlet.
2 If battery is completely empty, wait a few
minutes before switching clipper ON.
10 11 12
2
3 Turn Clipper ON to begin clipping (fig. 4).
4 When finished clipping, switch Clipper OFF
1
and unplug.
13 14 15
1
Cordless Hair Clipping
2
1 Charge according to directions. Unplug
Clipper from outlet and remove cord.
2 Turn Clipper ON to begin clipping (fig. 4).
16 17 18
2
3 If the charge runs low while clipping, the
charging light will blink orange (fig. 2).
1
4 If the charge runs out while clipping, simply
connect cord provided to Clipper and outlet
to continue clipping.
19 20 21
2
Hair Clipping
Use this Clipper for its intended household
w
use as described in this manual.
Make sure that the appliance is fully charged
w
before you start clipping hair.
Before you start clipping, make sure that the
w
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
Only use the appliance on clean, dry hair.
w
Do not use on freshly washed hair.
w
Before you begin, comb the hair in the direction
w
of growth (fig. 5).
To achieve optimal clipping results, always move
w
the appliance slowly through the hair against
the direction of hair growth.
Clipping with hair clipping comb
1 Be certain the Clipper is in the OFF position.
2 Slide the hair clipping comb into the guiding
grooves on both sides of Clipper and push
until you hear it 'click' into place (fig. 6).
Make sure the comb locks properly into position.
3 Turn the Adjustable Wheel Hair Length After Each Use:
Setting Selector to the desired setting (fig. 7).
1 Make sure the Clipper is switched OFF
The Clipper can cut hair up to 24 different
and disconnected from the electrical outlet.
lengths. See table below.
2 Remove the hair clipping comb by pressing
4 The remaining hair length is indicated in
and sliding the comb off the Clipper (fig. 9).
millimeters on the adjustable wheel.
When you are clipping for the first time,
3 Clean the comb with the brush supplied or
start at the maximum clipping length setting
rinse under warm water (fig. 11).
(23mm/7/8 in.) to familiarize yourself with the
appliance and prevent accidentally trimming
Press the release button (1) and remove the
4
hairs too short. As you become familiar with the
cutting unit (2) (fig. 12).
settings, adjust the Hair Length Selector to desired
trimming length.
5 Clean the cutting unit with the brush
Trimming Length Settings Table
supplied or rinse under warm water (fig. 13).
1mm – 3/64 in. 13mm – 1/2 in.
6 Clean the inside of the Clipper with the
brush supplied (fig. 14).
2mm – 5/64 in. 14mm – 9/16 in.
3mm – 1/8 in. 15mm – 5/8 in.
7 Shake off any excess water and allow to
4mm – 5/32 in. 16mm – 21/32 in. air dry.
5mm – 3/16 in. 17mm – 11/16 in.
8 Reattach cutting unit by inserting the notch
6mm – 1/4 in. 18mm – 23/32 in.
of the cutting unit into the guiding slot.
7mm – 9/32 in. 19mm – 3/4 in.
9 Push the cutting unit back onto the Clipper.
8mm – 5/16 in. 20mm – 25/32 in.
10 Clean the handle and the adapter with a
9mm – 3/8 in. 21mm – 13/16 in.
soft, dry cloth.
10mm – 13/32 in.
22mm – 55/64 in.
NOTE: The Clipper does not need any lubrication.
11mm – 7/16 in. 23mm – 7/8 in.
12mm – 15/32 in.
Replacing the Cutting Unit
If your cutters become damaged or worn, do
5 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain not continue using the Clipper. Replace cutters
immediately.
an even result (fig. 8).
1 Press the release button (1) and remove the
6 Since all hairs do not grow in the same
cutting unit (2) (fig. 12).
direction, move the appliance slowly over the
crown from different directions (i.e. upwards,
2 Place the notch of the new cutting unit in
downwards and across) to achieve an even
the guiding slot (1) and push the cutting unit
result.
onto the Clipper (2) (fig. 15). You will hear
a ‛click'.
7 Always move the appliance against the
direction of hair growth.
This Clipper has no other user-serviceable parts.
For assistance call 1-800-243-3050.
8 Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
Assistance
For assistance, call toll free:
9 For best results with curly, sparse or long
hair, use a styling comb to guide the hair
1-800-243-3050
towards the Clipper.
or visit our website:
www.philips.com/support
10 Switch the Clipper off regularly during
clipping and remove the hair clipping comb
Online information is available 24 hours a day,
to blow and/or shake out hair that has
7 days a week.
accumulated.
TIP: Write down the settings you have used to create
Storage
a certain hairstyle as a reminder for future clipping
Be sure Clipper is switched OFF. Remove cord
sessions.
w
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
Clipping without hair clipping comb
banged, or subject to damage.
Use the Clipper without a comb to clip hair Do not wrap cord around Clipper when
w w
storing.
very close to the skin (0.5mm/1/32 inch) or to
contour the neckline and area around the ears. Store cord in a safe location where it will not
w
be cut or damaged.
1 Remove the hair clipping comb by pressing Do not place or store Clipper where
w
it can fall or be pulled into a tub or sink, water
and sliding the comb off the Clipper (fig. 9).
or other liquid while plugged in.
Be careful when you are clipping without comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
Battery Removal
This Philips Norelco Clipper contains a
2 To contour the hairline around the ears,
w
rechargeable Lithium-Ion battery which must
comb the hair ends over the ears.
be disposed of properly (fig. 16).
Battery should only be removed when
3 Tilt the Clipper in such a way that only
w
Clipper is to be discarded.
one edge of the cutter blades touches the
hair ends when you shape the contours For assistance, visit our website,
w
www.philips.com/support or call
around the ears.
Only cut the hair ends. The hairline should be toll free: 1-800-243-3050.
close to the ear.
1 Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
4 To contour the nape of the neck or
sideburns, turn the Clipper and make
2 Allow Clipper to run until the battery is
downward strokes (fig. 10).
empty/depleted.
5 Move the Clipper slowly and smoothly
following the natural hairline. 3 Switch Clipper OFF.
4 Remove the hair clipping comb and cutting
Cleaning
unit from the handle.
Clean the attachments after each use.
w
5 Press the release button (1) and remove the
Always switch Clipper OFF, unplug and remove
w
power supply cord from Clipper before cutting unit (2) (fig. 17).
cleaning.
Do not use compressed air, abrasive cleaning 6 Insert the screwdriver between the motor
w
unit and the back panel of the appliance.
agents, scourers or aggressive liquids such as
alcohol, benzene, bleach or acetone to clean Press down the screwdriver as far as it will
go (fig. 18).
the Clipper and attachments.
Never clean, replace or remove Clipper
w
7 Tilt the handle of the screwdriver
attachments with motor ON.
Never rinse or immerse the Clipper in water downwards (1) and separate the back panel
w
from the appliance (2) (fig. 19).
or any other liquid.
Do not apply pressure to cutters.
w
8 Remove the back panel. Pull the bottom
Do not touch cutters with hard objects as this
w
part of the printed circuit board with the
may damage them.
rechargeable batteries attached from the
appliance (fig. 20).
During Use:
If cut hairs have accumulated in the comb 9 Cut the wires to separate the rechargeable
w
area, remove hairs by shaking, blowing or using batteries from the appliance (fig. 21).
cleaning brush provided.
S E R I E S 7 0 0 0
HAIRCLIPPER 7100
HC7452
Rechargeable
Cordless/Cord
Always here to help you
Question? Question?
Contact
Contact
Register your product and get support at
Philips Philips
Norelco Norelco
www.norelco.com/register
4222 002 8400 2
10 Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
11 Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
12 Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Philips
Norelco product, Model HC7452 (except cutters and comb) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product's nameplate means it is
listed by Underwriters' Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
© 2013 Philips Electronics North America Corporation. All Rights Reserved.
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper, send the product back and we'll refund you the
full purchase price. The Clipper must be shipped
prepaid by insured mail, insurance prepaid, have
the original sales receipt, indicating purchase
price and date of purchase, and the money-back
guarantee return authorization form enclosed.
We cannot be responsible for lost mail.
The Clipper must be postmarked no later than
45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6–8 weeks AFTER
receipt of returned product.