Makita EM2651LH Instruction Manual
Petrol brushcutter
Hide thumbs
Also See for EM2651LH:
- Original instruction manual (256 pages) ,
- Instruction manual (188 pages) ,
- Technical information (14 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Makita EM2651LH
Summary of Contents for Makita EM2651LH
- Page 1 Petrol Brushcutter EM2650UH EM2651UH EM2650LH EM2651LH INSTRUCTION MANUAL EM2650UH EM2650LH EM2651UH EM2651LH Important: Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully!
-
Page 2: Table Of Contents
English (Original instructions) Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are Table of Contents Page pleased to recommend to you the MAKITA Petrol Brushcutter which is the Symbols .................2 result of a long development programme and many years of knowledge and Safety instructions ............3... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS General Instructions – To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol Brushcutter. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. - Page 4 Start the Petrol Brushcutter only in accordance with the instructions. – Do not use any other methods for starting the engine! – Use the Petrol Brushcutter and the tools only for such applications as specified. – Only start the Petrol Brushcutter engine, after the entire assembly is done. Operation of the device is only permitted after all the appropriate accessories are attached! –...
-
Page 5: Maintenance Instructions
Cutting Tools Employ only the correct cutting tool for the job in hand. EM2650UH, EM2651UH, EM2650LH, EM2651LH with cutter blade, Nylon cutting head For cutting thick materials, such as weed, high grass, bushes, shrubs, underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work by swinging the Petrol Brushcutter evenly in half-circles from right to left (similar to using a scythe). - Page 6 Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by MAKITA. Use of non-approved accessories and tools means increased risk of accidents. MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools, or accessories.
-
Page 7: Technical Data
TECHNICAL DATA EM2650UH, EM2650LH EM2650UH EM2650LH Model Bike handle Loop handle Dimensions: length x width x height (without cutting blade) 1,765 x 620 x 474 1,765 x 330 x 264 Mass (without plastic guard and cutting blade) Volume (fuel tank) Volume (oil tank) 0.08 Engine displacement... - Page 8 TECHNICAL DATA EM2651UH, EM2651LH EM2651UH EM2651LH Model Bike handle Loop handle Dimensions: length x width x height (without cutting blade) 1,765 x 620 x 474 1,765 x 330 x 264 Mass (without plastic guard and cutting blade) Volume (fuel tank) Volume (oil tank) 0.08...
-
Page 9: Designation Of Parts
DESIGNATION OF PARTS EM2650LH EM2650UH EM2651LH EM2651UH ⑤ ⑤ ④ ⑫ ④ ⑨ ⑦ ⑦ ⑫ ⑨ ⑩ ⑧ ⑪ ⑪ ⑩ ⑯ ⑬ ⑬ ⑭ ⑭ ⑮ ⑮ ⑰ ⑱ DESIGNATION OF PARTS Fuel tank Rewind starter Air cleaner... -
Page 10: Mounting Of Handle
MOUNTING OF HANDLE CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely. -
Page 11: Mounting Of Protector
MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA cutter blades or nylon cutting head. Protector for metal blades Metal blade –... -
Page 12: Mounting Of Cutter Blade Or Nylon Cutting Head
MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily. – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench. -
Page 13: Before Start Of Operation
BEFORE START OF OPERATION Inspection and refill of engine oil – Perform the following procedure, with the engine cooled down. – Set the engine level, remove oil cap (Fig. 1), and check to see whether or not there is oil in the range between the upper limit and lower limit marks of the oil pipe (Fig. - Page 14 Note ● Do not replace oil with the engine in a tilted position. ● Filling with oil while engine is tilted leads to overfilling which causes oil contamination and/or white smoke. Point 2 in Replacement of oil: “If oil spills out” –...
-
Page 15: Correct Handling Of Machine
NOTE: Be careful not to trap clothing, etc., in the buckle. EM2650UH EM2651UH Detachment For EM2650LH, EM2651LH – In an emergency, push the notches (1) at both sides, and you can detach the machine from you. Be extremely careful to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity. - Page 16 3) Primer pump Primer Pump Continue to push the primer pump until fuel enters into the primer pump. (In general, fuel enters into the primer pump by 7 to 10 pushes.) If the primer pump is pushed excessively, an excess of gasoline returns to the fuel tank.
-
Page 17: Resharpening The Cutting Tool
STOP immediately and allow it to slow down fully. STOP EM2650LH EM2650UH EM2651LH EM2651UH ADJUSTMENT OF LOW-SPEED ROTATION (IDLING) When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw. CHECKUP OF LOW-SPEED ROTATION Carburetor –... - Page 18 Replacing the nylon cord – First, stop the engine. – Press on the housing latches inward to lift off the cover, then remove the Cover spool. Latches Press Press – Hook the center of new nylon cord into the notch in the center of the spool, Spool 80 mm (3 - 1/8”) with one end of the cord extending about 80 mm (3 - 1/8”) more than the...
-
Page 19: Servicing Instructions
SERVICING INSTRUCTIONS CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the plug cap off the spark plug (see “checking the spark plug”). Always wear protective gloves! To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular intervals. - Page 20 5) Set the engine level, and gradually fill up to upper limit mark with new oil. External mark (upper limit) 6) After filling, tightly secure oil cap, so that it will not loosen and cause leaks. If oil cap is not tightly secured, it may leak. External mark Internal stepped (lower limit)
- Page 21 SUPPLY OF GREASE TO GEAR CASE – Supply grease (Shell Alvania 2 or equivalent) to the gear case through the Gear case grease hole every 30 hours. (Genuine MAKITA grease may be purchased from your MAKITA dealer.) Grease hole CLEANING OF FUEL FILTER...
-
Page 22: Storage
STORAGE WARNING: When draining the fuel, be sure to stop the engine and confirm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire. ATTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the fuel tank and carburetor, and keep it at a dry and clean place. - Page 23 Operating time Before After Daily Shutdown/ Corres- 200h Item operation lubrication (10h) rest ponding P Inspect/clean Engine oil Replace Tightening parts Inspect (bolt, nut) Clean/inspect — Fuel tank Drain fuel Throttle lever Check function — Stop switch Check function Cutting blade Inspect Low-speed rotation Inspect/adjust...
-
Page 24: Troubleshooting
TROUBLESHOOTING Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership. State of abnormality Probable cause (malfunction) Remedy... - Page 28 Makita Corporation Anjo, Aichi, Japan www.makita.com 884951A229...