Philips SNV6520 Quick Start Manual

SNV6520_Belga_ENG 04-08-2005 11:29 Pagina 1
Philips SNV6520
ADSL Modem Multiservices PSTN Voice
Before You Start
This Before You Start card will help you to get your ADSL Modem Multiservices set up and connected to
the Internet quickly and easily. Just follow these steps:
Step 1: Check your package contents
Step 2: Set up your ADSL Modem Multiservices
Step 3: Configure your PC for Dynamic Addressing
Step 4: Configure your Wireless Modem Multiservices
Step 5: Configure your Telephone Settings
Step 6: Configure Wireless Security (optional)
> > > Before you install the unit, check that your ADSL line is working correctly on the phone socket where you plan
to connect your ADSL Modem Multiservices. Make sure that you have properly installed a splitter (not included, refer
to your Service Provider documentation).
1
Step 1
Check your package contents
You should have all of these:
ADSL Modem Multiservices Manual on CD Power Supply
Black RJ-11 Before You Start Card Grey RJ-45
Telephone Cable Ethernet Cable
If you don 't have everything, contact your supplier immediately.
2
Step
2
Set up your ADSL Modem Multiser vices PSTN Voice
1. Select a location for your ADSL Modem Multiservices
Install the ADSL Modem Multiservices near your PC or another location where you have easy access.
Keep ethernet cables away from power cords and other sources of electrical interference. Place the
ADSL Modem Multiservices, with the antenna in upright position, in a location where air can circulate
freely around it.
2. Plug the Power Supply into an appropriate electrical outlet.
Connect the other end to the Power Input on the backside of the ADSL Modem Multiservices. Turn
the power ON with the Off/On Switch.The LED light (PWR) should come on solid green.
3. Connect the ADSL Modem Multiservices to your ADSL RJ11 wall jack.
Plug one end of the black RJ-11 Telephone Cable into the port labeled "ADSL" on the ADSL Modem
Multiservices back panel until you feel it click. Insert the other end of the telephone cable into the
telephone jack (or filter/ splitter) connected to your ADSL service.
The ADSL light should blink for up to two minutes and then come on solid green.
4. Connect the ADSL Modem Multiservices to your computer
Connect one end of the Gray RJ-45 Ethernet Cable to your PC's Ethernet port and the other end to
one of the LAN ports of the ADSL Modem Multiservices.The LAN indicator light should come on
solid green for the port where you connected your Ethernet cable and your PC is on.
5. Connect the ADSL Modem Multiservices to your Telephone
Plug one end of the black RJ-11 Telephone Cable into the port labeled "Phone1" on the ADSL
Modem Multiservices back panel until you feel it click. Insert the other end of the telephone cable
into the telephone jack of your telephone.
SNV6520 Rear View
ADSL LAN1 LAN2 LAN3 LAN4 PWR RESET USB Phone1 Phone2
ON/OFF
Connect each computer or other device in your network to the ADSL Modem Multiservices with an
Ethernet cable or wirelessly.
A maximum of four computers or devices may access the Internet via the ADSL Modem Multiservices at
one time
SNV6520 LED Indicator Lights
1 8
2 7
3 6
4 5
1. Phone2, 1 • ON: When Phone is OFF-Hook talking on a Call
• Blinking Green: On an Incoming Telephone Call when it rings the phone or in
call waiting stage
• Off: When modem is having no communication on ADSL or Internet Telephony
2.TEL • Solid Green: When Telephone registration is successful
• Off: When there is no connection
3. USB • Solid Green: When USB device is up and connected
• Off: When there is no connection
4. LAN 1, 2, 3, 4 • Green when connected to each port on the LAN
• Blinking green when there is activity on each port
5. WL • Off = Wireless disabled
• On = Wireless enabled
• Blinking = Wireless traffic
6. ON LINE • Green when Link is Up
• Blinking when sending and receiving data
7. ADSL • Blinking green when initializing
• Green when initialized
8. PWR • Green when power is on
3
Step 3
Configure your PC for Dynamic Addressing
Repeat these steps for each computer that you want to connect to your ADSL Modem Multiservices.
A maximum of four computers or devices may access the Internet via the ADSL Modem Multiservices at one
time
Microsoft Windows:
Step 1: Go to the TCP/ IP Properties settings on your computer by:
a). for Window 98, ME, and 2000 : Start menu > Settings > Control Panel > Network
(or Network and Dial-up Connections > Local Area
Connection > Properties) > TCP/IP [your network card]
or Internet protocol [TCP/IP] > Properties
b). for Window XP Click Start menu > Control Panel > Network and Internet
Connections > Network Connection > Local Area
Connection > Properties > Internet protocol [TCP/IP]
> Properties
Configure Your PC for Dynamic Addressing
Step 2: Select "Obtain an IP address automatically".
Step 3: Select "Obtain DNS server address automatically", if available.
Step 4: Remove any previously configured Gateways, if available.
Step 5: Click OK. Restart if prompted.
Proceed to the next section 'Step 4: Configure Your Philips ADSL Modem Multiservices'.
Macintosh Mac OS 9.2 and higher or Mac OS X 10.1.5 or higher :
Step 1: Access the TCP/ IP or Network control panel.
a. Mac OS 9 follows a path like this: Apple Menu > Control Panels > TCP/IP Control Panel
b. Mac OS X follows a path like this: Apple Menu > System Preferences > Network
Step 2: Select Built- in Ethernet.
Step 3: Select Configure Using DHCP.
Step 4: Close and Save, if prompted.
4
Step
4
Configure your ADSL Modem Multiser vices PSTN Voice
1. Open your Web browser (e.g. Netscape or Internet Explorer) from the computer that is
connected to the ADSL Modem Multiservices.
Enter http://192.168.1.1 in the URL Address text box and press the Enter key. In case the Philips ADSL
Modem Multiservices displays the Login Screen, click the "Login" button (leave the Password field blank) to
proceed to the Quickstart page.
2.The ADSL Modem Multiservices displays the Quickstart Web page.
Enter the Username and Password supplied by your Internet Service Provider.