Sony cdx-4170r fm/mw/lw compact disc player (45 pages)
Summary of Contents for Sony CDX-454RF
Page 1
Approx. 262 × 90 × Dimensions 185 mm × 3 × 7 in.) (w/h/d) Mass Approx. 2.1 kg (4 lb. 10 oz.) COMPACT DISC CHANGER SYSTEM Sony Corporation 9-873-373-02 2002C0500-1 e Vehicle Company C 2002.03 Published by Sony Engineering Corporation...
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CDX-454RF/454XRF Ver 1.1 SECTION 1 SERVICING NOTES JIG ON REPAIRING NOTES ON HANDLING THE OPTICAL PICK- When repairing this set, connect the jig (cord) for RF output ex- UP BLOCK OR BASE UNIT tract (Part No. J-2502-058-1) and power supply (Part No. J-2502- 058-2) as the figure shown below.
CDX-454RF/454XRF SECTION 2 This section is extracted from instruction manual. GENERAL Location of controls Refer to the pages for details. Wired remote (RM-X82RF) 1 DISC (disc select) buttons 5, 6, 8 2 AMS (Automatic Music Sensor/manual search) control 6 3 D-BASS indication 7...
CDX-454RF/454XRF Installation Installation Instalaci n CD changer Changeur de CD Cambiador de discos compactos •Choose the mounting location carefully, observing the following: •Elija cuidadosamente el lugar de montaje teniendo en cuenta lo •Choisir l’emplacement de montage en tenant compte des —...
Page 6
CDX-454RF/454XRF Wired remote Mando a distancia al mbrico •Avoid mounting it where it may: •Evite montarlo donde pueda: — hinder normal driving activities. — estorbar las operaciones normales de — block the airbag (especially passenger-side) conducción. in operations. — bloquear el funcionamiento del “airbag”...
CDX-454RF/454XRF Connections Conexiones Conexiones Caution Pr cautions Precauciones •This unit is designed for negative ground 12 V DC operation only. •Cet appareil est uniquement conçu pour fonctionner sur 12 V CC •Esta unidad está diseñada para emplearse solamente con negativo a •Before making connections, turn the car ignition off to avoid short...
CDX-454RF/454XRF SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.
CDX-454RF/454XRF 3-6. ELJ MOTOR ASSY (ELEVATOR) (M104) 1 screw (PTT2 × 4) 2 bracket (EVM.S) 3 ELJ motor assy (elevator) (M104) 3-7. ESCUTCHEON (T) 3 two claws 2 Remove the claw in the direction of arrow A . 4 Remove the ditch in the direction of arrow B .
CDX-454RF/454XRF 3-8. CHASSIS (U.S) SUB ASSY 2 Remove the edge in the direction 1 three screws of arrow A . (PTT2 × 4) 1 two screws (PTT2 × 4) 5 chassis (U.S) sub assy 1 screw (PTT2 × 4) 4 spring (SUT) 3-9.
CDX-454RF/454XRF 3-10. RF BOARD 3 two screws (PS2 × 4) 4 RF board 3 two screws (PS2 × 4) 2 Remove four solders of the LSW board leads and spindle motor leads (M102). 2 Remove two solders of the sled motor leads 1 OP flexible board (CN102).
CDX-454RF/454XRF 3-12. LSW BOARD, SPINDLE MOTOR (S) SUB ASSY (M102) 8 two precision screws (P1.7 × 2.2) 3 spring (chucking) 6 retainer (disc) 1 precision screw (P2 × 2.5) 4 precision screw (P2 × 2.2) 5 bracket (CP) 2 LSW board 9 Remove the spindle motor (S) sub assy (M102) in the direction of the arrow.
CDX-454RF/454XRF 4-3. GEAR (LOMINI)/(LOAD 1) ASSY gear (LOAD 2) 2 Attach the gear (LOMINI) at the position shown in Fig. A. gear (LOMINI) shaft (rotary prevention C) chuck plate 1 Move the lever (LOCK 3A) fully in the direction of arrow B to move the chuck plate up.
CDX-454RF/454XRF SECTION 5 MECHANICAL ADJUSTMENTS • Elevator Height (Address) Adjustment Adjustment Method: Note: This adjustments is necessary when the system controller (IC201), variable resistor (RV201), slider (R), slider (L), or chassis (ELV) 1. Load a disc magazine, and place the set vertically as shown was replaced for any repair.
CDX-454RF/454XRF SECTION 6 ELECTRICAL CHECK Note: Focus Bias Check 1. This adjustment is performed with the set placed horizontally. 2. Power supply voltage: DC14.4 V (more than 3 A). Connection: 3. Be sure to use the disc “YEDS-18” parts code: 3-702-101-01, but only –...
Page 19
CDX-454RF/454XRF Tracking Offset Check Connection: – RF Board (Component Side) – oscilloscope (DC range) – TP (VC) IC101 TP (TE) Procedure: 1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF board. 2. Put the set into play mode by loading the disc (YEDS-18).
CDX-454RF/454XRF 7-2. BLOCK DIAGRAM – MAIN Section – RV701 TRANSMITTER MODULATION CN703 SENSITIVITY L, R PRE-EMPHASIS L. P. F. & LIMITER OUTPUT RF IN RF OUT (Page 21) MUTING RF AMP L. P. F. PRE-EMPHASIS L. P. F. BUFFER, AMP...
CDX-454RF/454XRF 7-3. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location Note on Printed Wiring Board: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
CDX-454RF/454XRF 7-5. SCHEMATIC DIAGRAM – RF/LSW Boards – • • See page 32 for Waveforms. See page 32 for IC Block Diagrams. (Page 28) The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety.
CDX-454RF/454XRF 7-10. PRINTED WIRING BOARD – FM Board – • See page 23 for Circuit Boards Location. FROM CAR ANTENNA RELAY BOX BATT MASTER UNIT REMOTE COMMANDER FM BOARD CN703 RM-X82RF OUTPUT FM BOARD (CONDUCTOR SIDE) (COMPONENT SIDE) CN302 CN303...
Page 35
CDX-454RF/454XRF – FM Board – IC701 BH1415F-E2 SHIFT REGISTER – L. P. F. PRE-EMPHASIS MUTE & LIMITER L. P. F. – PROGRAM COUNTER PHASE DETECTOR...
CDX-454RF/454XRF 7-12. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC201 CXP740056-011R (SYSTEM CONTROLLER) Pin No. Pin Name Description 1 to 3 — Not used AMUTE Audio line muting on/off control signal output “H”: muting on CDXLT Serial data latch pulse signal output to the DSP...
Page 37
CDX-454RF/454XRF Pin No. Pin Name Description CH.F Motor drive signal (save direction) output to the chucking motor drive “L” active CH.R Motor drive signal (chucking direction) output to the chucking motor drive “L” active ELVR Motor drive signal (elevator down direction) output to the elevator motor drive “L” active ELVF Motor drive signal (elevator up direction) output to the elevator motor drive “L”...
CDX-454RF/454XRF 8-2. GENERAL SECTION-2 MG-251A-137 RV202 not supplied not supplied not supplied supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-047-852-01 DAMPER (T) 3-041-218-21 ESCUTCHEON (T) X-3381-478-1 CASE (LOWER. T) ASSY...
CDX-454RF/454XRF 8-6. MECHANISM DECK SECTION-4 (MG-251A-137) not supplied M102 not supplied M101 not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.
CDX-454RF/454XRF SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 45
CDX-454RF/454XRF MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R310 1-216-841-11 METAL CHIP 1/16W C102 1-164-360-11 CERAMIC CHIP 0.1uF R311 1-216-839-11 METAL CHIP 1/16W C103 1-164-360-11 CERAMIC CHIP 0.1uF R312 1-216-841-11 METAL CHIP 1/16W C104 1-162-970-11 CERAMIC CHIP 0.01uF...
Page 46
CDX-454RF/454XRF MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C416 1-126-382-11 ELECT 100uF R141 1-216-834-11 METAL CHIP 1/16W R142 1-216-834-11 METAL CHIP 1/16W < CONNECTOR > R143 1-216-834-11 METAL CHIP 1/16W R144 1-216-834-11 METAL CHIP...
CDX-454RF/454XRF REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.11...