Sony RCD-W10 Service Manual

Compact disc recorder

Hide thumbs Also See for RCD-W10:

Operating instructions manual (32 pages)

Manual (51 pages)

Operating instructions manual (35 pages)

Table Of Contents

100

page of 100

/ 100
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Summary of Contents for Sony RCD-W10

Page 1 20 Hz - 20,000 Hz (±0.5 Wavelength: 660 nm Output level: –18 dBm PHONES (Phono jack) Load impedance: 32 ohms Output level: 12mW COMPACT DISC RECORDER Sony Corporation 9-874-152-02 2003L16-1 Home Audio Company © 2003.12 Published by Sony Engineering Corporation...
Page 2 DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 4-238-401-6π Canadian CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
RCD-W10 TABLE OF CONTENTS Unleaded solder 1. SERVICING NOTE ····················································· Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. 2. GENERAL ··································································· (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
Page 4: Servicing Note
RCD-W10 SECTION 1 SERVICING NOTE Self-diagnosis Function NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT When the self-diagnosis function is activated to The laser diode in the optical pick-up block may suffer electrostatic prevent the player from malfunctioning, three...
Page 5: General
RCD-W10 SECTION 2 GENERAL POWER button PLAY MODE button H button TIME button OPEN/CLOSE A button DISPLAY button CD SYNCHRO NORMAL button YES button l AMS L knob CD SYNCHRO HIGH button OPEN/CLOSE A button CLEAR button H button MENU/NO button...
Page 6: Disassembly
RCD-W10 SECTION 3 DISASSEMBLY Note : Disassemble the unit in the order as shown below. CASE (409538) LOADING PANEL (1CD) LOADING PANEL (CDR) FRONT PANEL SECTION DISPLAY BOARD CDR MECHANISM DECK (CDM65-RBD1) TRAY MOTOR ASSY (LOADING) (M201) CDR BOARD OPTICAL PICK-UP (KRM-220CAA)
Page 7: Case (409538)
RCD-W10 Note : Follow the disassembly procedure in the numerical order given. 3-1. Case (409538) 4 case (409538) 2 two screws 3 two screws (case 3 TP2 3 x 8) (case 3 TP2 3 x 8) 1 two screws (case 3 TP2 3 x 8) 3-2.
Page 8: Loading Panel (Cdr)
RCD-W10 3-3. Loading Panel (CDR) 3 two hooks 5 l oading panel (CDR) CD mechanism deck (CDM65-RBD1) 1 Slide the lever to the direction of arrow. front panel side lever 3-4. Front Panel Section 4 connector 1 c onnector (2 core) (CN920)
Page 9: Display Board
RCD-W10 3-5. DISPLAY Board 8 Remove the soldering. HARNESS PROCESSING 7 c law 2 two knobs (AMS) POWER-SW board 5 three screws (+BVTP 2.6 × 8) 9 CD-EJECT board 3 four screws (+BVTP 2.6 × 8) 4 CD-SW board 1 knob (AMS)
Page 10: Tray
RCD-W10 3-7. Tray 2 Pull the tray while pressing the claw of 1 Slide the lever (cam (CH)) to the direction of arrow. the chassis in the direction of the arrow. claw front panel side lever (cam (CH)) chassis 4 t ray 3 Pull the tray while pressing the claw of the chassis and the claw of the tray in the direction of the arrow.
Page 11: Holder (Mg) Sub Assy, Dust Cover
RCD-W10 3-9. Holder (MG) Sub Assy, Dust Cover 4 three s crews (+BVTP 2.6 × 8) 5 dust cover 3 holder (MG) sub assy 1 two claws 2 two claws 3-10. Optical Pick-Up (KRM-220CAA) 2 two screws 1 two step screws...
Page 12: Motor Assy (Loading)(M201)
RCD-W10 3-11. Motor Assy (Loading)(M201) 1 Slide the cam (CH) to the direction of arrow. 2 Remove the belt (loading) from the pulley of the motor assy. 3 t wo claws 4 m otor assy (loading) (M201) 3-12. Cam (CH) q;...
Page 13: Cd Mechanism Deck (Cdm66C-30B61B)
RCD-W10 3-13. CD Mechanism Deck (CDM66C-30B61B) 3 three screws (+BVTP 3 × 8) 4 CD mechanism deck (CDM66C-30B61B) 1 connector (5P) (CN680) 2 flexible flat cable (23core) (CN101)
Page 14: Tray (66)
RCD-W10 3-14. Tray (66) 1 Turn the cam to the direction of arrow. 3 hook 4 hook 7 hook 8 tray (66) 6 hook...
Page 15: Bd Board
RCD-W10 3-15. BD Board 1 Remove soldering from the four points. 2 flexible flat cable (16core) 3 BD board 3-16. Optical Block Section 4 optical block section 1 floating screw shaft (BU holder) cam (66) Rotate the cam (66) in the direction of 2 to move...
Page 16: Main Board
RCD-W10 3-17. MAIN Board qs four screws (+BVTT 3 × 6) qa two screws (+BVTT 3 × 6) qf power transformer 7 flexible flat cable (23core) (CN660) qd Remove the soldering. connector (5core) (CN680) qg MAIN board 5 flexible flat cable...
Page 17 RCD-W10 MEMO...
Page 18: Test Mode
RCD-W10 SECTION 4 TEST MODE Setting the Test Mode BU Test Mode (Deck A) Procedure: Procedure: 1. Press the POWER button to POWER on. 1. Enter the test mode, then turn the l AMS L (DECK B) 2. Press the l AMS L (DECK A), [SBM] and l AMS knob to display “BU Test”, and press the l AMS L...
Page 19 RCD-W10 FL ALL OFF Mode CDR History Display Procedure: Procedure: 1. Enter the test mode, then turn the l AMS L (DECK B) 1. Enter the test mode, then turn the l AMS L (DECK B) knob to display “FL ALL OFF”, and press the l AMS L knob to display “CDR History”, and press the l AMS L...
Page 20 RCD-W10 3 Operation mode 5 Write POWER (integer of mW x 10, available during write bit 7: Speed processing) 0: normal speed examples: 00 means unavailable 1: x4 speed (when 3 operation mode is not recording) bit 6 to bit 0: Number of inner condition : A3 means 163(decimal), i.e.
Page 21: Electrical Adjustments
RCD-W10 SECTION 5 ELECTRICAL ADJUSTMENTS Note: A clear RF signal waveform means that the shape “◊” can be CD SECTION (DECK A) clearly distinguished at the center of the waveform. Note : 1. CD Block is basically designed to operate without adjustment.
Page 22: Cd-R/Rw Section
RCD-W10 CD-R/RW SECTION The following is the method of locating the faulty point and (w/ Serial I/F) electrical adjustment. Connection and Setting of Programs COM1 1-1. Connection RCD-W10 RS-232C Cable Oscilloscope MPXOUT 0-756-358-11 CDM65-RBD1 SERVICE RESET CONTROL FIRM Cables for Jig connecting...
Page 23 RCD-W10 Ver 1.1 2003.12 1-2. Equipments to prepare Test Object Both RBD1 and CDM65-RBD1 shall be tested. RBD1 : Flash Memory Writing of of Circuit Test by Self-diagnostics CDM65-RBD1 : Electrical Adjustment Performance Test (With 9 Cables, Parts No.J-2501-223-A) Windows95/98/2000/Me with COMport (RS-232C)
Page 24 RCD-W10 1-3. Setting of Programs (Tera Term Pro and Service macro) Confirmation of System (Windows 98 is used in this explanation) Preparation for Terminal software 1) Set up the serial port from OS. Select Start → Settings → Control Panel and select System →...
Page 25 RCD-W10 Ver 1.1 2003.12 Press “Advanced...” button (see Fig.1-2) Remove the check “Use FIFO buffers ...” (see Fig.1-3) 4 Fig. 1-3 Unzip the file “ttermp23.zip” by PC. (The file “ttermp23.zip” is distributed together with the service manual.) After unzip the files, you can find setup.exe.
Page 26 RCD-W10 b) Terminal setup Set the parameters as below. New-line receive : CR transmit : CR After settings, press “OK” button. (see Fig.1-6) 4 Fig. 1-6 General setup Select the language and press “OK” button. (see Fig.1-7) 4 Fig. 1-7 d) Saving the setup Select Setup →...
Page 27 RCD-W10 Repair Works That Require Electrical Adjustment In the case of repair works as shown below, electrical adjustment is required. Locating the faulty point KRM-220CAA is replaced. RBD1 is replaced. The parts shown in the List (1) is replaced. Electrical adjustment is not required.
Page 28 RCD-W10 Locating the Faulty Point 3-1. Laser Power Check 1) Select the menu as follows. Control → Macro, and select LDPtestL_S.ttl. Press “Open”. (Fig. 3-1, 3-2) 4 Fig. 3-1 4 Fig. 3-2 2) Press the “RESET” button (SW101) of the jig as prompted by the display.
Page 29 RCD-W10 When the display shown in Fig. 3-4 appears, set the Range of a laser power meter to “1 mW” and press “OK”. 4 Fig. 3-4 Check that the laser power meter reading satisfies the following requirement. When the laser power satisfies the required specification, press “OK”.
Page 30 RCD-W10 9) Check that the message “Power Check End” appears on display. (Fig. 3-9) If the measurement result is outside the specification value, either perform Section 4. CDM65-RBD1 Electrical Adjustment, or locate the cause of the error by performing the Laser Deterioration Judgment.
Page 31 Connect the CDM65-RBD1 (abbreviated as CDM65 hereafter) that is going to be repaired, the jig and a PC following the Connection Diagram as shown in section 1-1. Turn on the power of the RCD-W10 in which the CDM65 is installed. Start up the TeraTermPro that is installed in PC. Set the switch S510 on the jig to “CONTROL”.
Page 32 RCD-W10 6) Type diagno [Enter] from keyboard of PC. Note 6-1 : When the KRM-220CAA is connected, the spindle motor rotates at a high speed. If the message “Diagnosis END!” appears, press the “RESET” button and stop the spindle. Note 6-2 : When the KRM-220CAA is connected (i.e. when the FFC for optical laser unit is connected to CN101 is connected), ignore the message “AK8567 (w/o OP)
Page 33 RCD-W10 Type the filename in which result of electrical adjustment is going to be saved. Press “OK”. (Fig. 3-19) 4 Fig. 3-19 Confirm that the message “completed!” appears. The EEPROM data is backed up. (Fig. 3-20) 4 Fig. 3-20 Perform step 1) through step 6) of section “3-3. Use of Self Diagnosis Function-1”.
Page 34 RCD-W10 8) Confirm that the message “completed!” appears. The EEPROM data is recovered. (Fig. 3-23) 4 Fig. 3-23 9) Perform the operation check. 3-5. Acquisition of Error History and Acquisition of Elapsed Operating Hours Check if error has occurred or not by performing the following steps. If error has occurred, it is interpreted and saved in the specific directory.
Page 35 RCD-W10 Press the “RESET” button (SW101) of the jig as prompted by the display. When there is no error, the display as shown in Fig. 3-26 appears. 4 Fig. 3-26 When error has occurred, the display as shown in Fig. 3-27 appears showing error history.
Page 36 RCD-W10 CDM65-RBD1 Electrical Adjustment 4-1. Laser Power Adjustment 1) Start up the TeraTermPro and set the switch S510 on the jig to “CONTROL”. 2) Select the menu as follows. Control → Macro, and select 01ldp_S.ttl. Press “Open”. (Fig. 4-1) 4 Fig. 4-1 3) Press the “RESET”...
Page 37 RCD-W10 When the display as shown in Fig. 4-6 appears, place the probe of the laser power meter on top of the optical laser unit, and press “OK”. (See Fig. 3-3-a, page 28) 4 Fig. 4-6 When the display as shown in Fig. 4-7 appears, set the Range of a laser power meter to “1 mW”...
Page 38 RCD-W10 10) Adjust the laser output power as follows. The laser output power (i.e., laser power meter reading) should satisfy the specification shown below. LEADER LPM-8001 : 4.6 +/- 0.1 mW (4.5 to 4.7 mW) To increase the laser output power Press [Yes] of the “Up?”...
Page 39 RCD-W10 12) When the display shown in Fig. 4-18 appears, remove probe of the laser power meter and press OK. 4 Fig. 4-18 13) Check that the message “Laser Power CAL completed!” appears. (Fig. 4-19) NG Judgment Result Indication 4 Fig. 4-19 4-1-1.
Page 40 RCD-W10 Note :The clear RF signal waveform means that the shape “ ” can be clearly distinguished at the center of the waveform. RF signal waveform VOLT/DIV : suitable value TIME/DIV : 500ns 4 Fig. 4-22 5) As prompted by the message shown in Fig. 4-24, check that the waveform as shown in Fig.
Page 41 RCD-W10 4-3. CD-RW Playback Adjustment Select the menu as follows. Control → Macro, and select 03cdr_S.ttl. Press “Open”. Place the test CD TCD-W091W on the tray as prompted by the display and press “OK”. (Fig. 4-27) 4 Fig. 4-27 Press the “RESET” button (SW101) of the jig as prompted by the display.
Page 42 RCD-W10 7) Check that the message “CDRW PB-CAL completed!” appears. (Fig. 4-34) NG Judgment Result Indication 4 Fig. 4-34 4-3-1. Playback Measurement NG! Contents: This message appears when the BLER (Block Error Rate) during playback is outside the specification. Measure : Check if there is any abnormality in RBD1.
Page 43 RCD-W10 Press the H button of Deck A. After playback starts, press “OK”. (Fig. 4-37) 4 Fig. 4-37 When the message as shown in Fig. 4-38 appears some seconds later, select 4x of the test mode (refer to page 19, Play Speed Selection Mode (Deck A)) PLAYBACK SPEED.
Page 44 RCD-W10 4-5. CD-RW Recording Adjustment and Self Record/Playback Check 1) Select the menu as follows. Control → Macro, and select 05cdrw_S.ttl. Press “Open”. 2) Place the test CD disc PATD-012 on the Deck A. Place the recording CD-RW disc (see Note: 4-5-1) on the tray (Deck B) as prompted by the display and press “OK”.
Page 45 RCD-W10 As prompted by the message shown in Fig. 4-48, check that the waveform as shown in Fig. 4-47 appears on an oscilloscope. RF signal waveform VOLT/DIV : suitable value TIME/DIV : 500ns 4 Fig. 4-47 4 Fig. 4-48 As prompted by the message shown on display, check that the waveform as shown in Fig. 4-49 appears on an oscilloscope.
Page 46 RCD-W10 4-6. VWDC Check 1) Select the menu as follows. Control → Macro, and select 06vwdc_S.ttl. Press “Open”. 2) As prompted by the message shown in Fig. 4-51, remove the disc from the tray and press “OK”. 4 Fig. 4-51 3) Because this step saves the result of electrical adjustment in a file, there can be a case that the dialog as shown in Fig.
Page 47 RCD-W10 4-7. NG Message List Message Cause Tray OPEN NG! The tray has not opened within the specified time. Tray Close NG! The tray has not closed within the specified time. SLEDIN NG! The sled has not moved toward inner circumference within the specified time.
Page 48 RCD-W10 Operation Check 5-1. Erasing the Error History 1) Select the menu as follows. Control → Macro, and select ErrHistClear.ttl. Press “Open”. (Fig. 5-1, 5-2) 4 Fig. 5-1 4 Fig. 5-2 2) Press the “RESET” button (SW101) of the jig as prompted by the display.
Page 49 RCD-W10 5-2. Playback Check using TCD-W032W Install the CDM65 in the equipment and install the TCD-W032W in Deck B. Rotate the l AMS L (Deck B) knob to select the track 16. Start playback by pressing the same knob or by pressing the H (Deck B) button.
Page 50 RCD-W10 Supplementary Information Method to Erase the CD-RW Disc * Erase it in the following procedure, to reuse the CD-RW disc to electrical adjustment, or to use a disc other than blank. * Be sure to erase it in the following procedure, to use the disc used for electrical adjustment for other uses.
Page 51 RCD-W10 Check that the time display as shown by the arrow mark in Fig. A-4 is updated after a while. 4 Fig. A-4 When update of time display is stopped and rotation of spindle is stopped, press the STOP button (SW501) of the Jig, and then press the...
Page 52 RCD-W10 MEMO...
Page 53: Diagrams
RCD-W10 SECTION 6 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING • Waveform • Circuit Board Location BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in IC103 qg (RFAC) each block.) For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. p : pF. 50 WV or less are not indicated except for electrolytics and tantalums.
Page 54: Block Diagrams - Cd-R Section
RCD-W10 6-1. Block Diagrams – CD-R Section – OPTICAL RF AMP CD DEC/ENC PICK-UP BLOCK IC101 IC201 (KRM-220CAA) EQRF EFM IN LD-VCC +5V A µ COM SLCO0 PD-VCC IC501 (1/2) PD-VC RRFVC(1V) MPXOUT FPD-VC HAVC MPXOUT IO15 IC103 IC502 +2.5V-2...
Page 55: Cd Section
RCD-W10 – CD Section – IC104 SELECTOR OPTICAL PICK-UP BLOCK DIGITAL SERVO RF AMP (A-MAX.3) DIGITAL SIGNAL PROC. IC103 D/A CONV. IC101 IC105 DOUT CD & SYSTEM CONTROL RFAC RFAC IC1 (1/2) I5-10 DATA DATA RFDCO RFDC I1-6 CLOK Q101 XLAT •...
Page 56: Power/Display Section
RCD-W10 – POWER/DISPLAY Section – TR900 CD & SYSTEM CONTROL FL DRIVER IC1 (2/2) IC760 FL750 SEG01 RV780 FLUORESCENT SEG35 IC460 FL-LD-DT DISPLAY TUBE REC LEVEL D461 -36V FL-LD-CLK COM2 -36V FLCS COM23 Q761,762 IC430 FL-LED-RST RESET S921 COM1 GRID...
Page 57: Printed Wiring Board - Bd Section
RCD-W10 6-2. Printed Wiring Board – BD Section – • : Uses unleaded solder. • See page 53 for Circuit Boards Location. (A-MAX.3) IC201 IC103 IC101 MAIN (RFAC) IC105 (Page 65) IC104 (TE) (FE) (DVC) IC102 • Semiconductor Location Ref. No. Location...
Page 58: Schematic Diagram - Bd Section
RCD-W10 6-3. Schematic Diagram – BD Section – • See page 53 for Waveform. • See page 71 for IC Block Diagrams. TP39 TP49 (RFAC) IC104 TC74HC4052 AFT(EL) TP28 CN102 IC103 TP26 C210 CXA2581N-T 820p C107 R120 120k C112 C118...
Page 59: Printed Wiring Board - Cd-R Section (Side A)
RCD-W10 6-4. Printed Wiring Board – CD-R Section (Side A) – • See page 53 for Circuit Boards Location. NOT USED (LASER POWER METER) (TO JIG) IC 104 IC 150 • Semiconductor Location IC 102 Ref. No. Location IC102 IC104...
Page 60: Printed Wiring Board - Cd-R Section (Side B)
RCD-W10 6-5. Printed Wiring Board – CD-R Section (Side B) – • See page 53 for Circuit Boards Location. IC 103 IC 204 IC 110 • Semiconductor Location Ref. No. Location IC 302 D101 D102 IC 101 IC101 IC103 IC 301...
Page 61: Schematic Diagram - Cd-R Section (1/4)
RCD-W10 6-6. Schematic Diagram – CD-R Section (1/4) – • See page 53 for Waveform. • See page 78 for IC Pin Function. (TO JIG) NOT USED CN115 CN121 C126 C123 C125 2200p 4700p C122 680p C140 6.3V R157 C139...
Page 62: Schematic Diagram - Cd-R Section (2/4)
RCD-W10 6-7. Schematic Diagram – CD-R Section (2/4) – • See page 53 for Waveform. • See page 82 for IC Pin Function. CN112 CN111 CN110 R556 R555 TP531 TP534 C512 XREQI SDATAI 1000p C511 1000p IC504 TC7SET08FU TP532 TP533...
Page 63: Schematic Diagram - Cd-R Section (3/4)
RCD-W10 6-8. Schematic Diagram – CD-R Section (3/4) – • See page 71 for IC Block Diagrams. IC103(1/4) NJM2902V R131 C133 TP356 2.5V-2 C132 C130 C158 R140 6.3V R111 IC103(3/4) IC103(2/4) C157 NJM2902V C134 NJM2902V 6.3V TP355 2.5V-1 C131 R112...
Page 64: Schematic Diagram - Cd-R Section (4/4)
RCD-W10 6-9. Schematic Diagram – CD-R Section (4/4) – • See page 53 for Waveform. • See page 78 for IC Pin Function. R201 C248 C257 R294 C233 R225 C206 C203 C205 C226 C216 TP297 C289 6.3V C258 C210 L202 (3225) 6.3V...
Page 65: Printed Wiring Board - Main Section (Side A)
RCD-W10 6-10. Printed Wiring Board – MAIN Section (Side A) – • : Uses unleaded solder. • See page 53 for Circuit Boards Location. C802 D805 IC 100 IC 1 • Semiconductor Location Ref. No. Location D181 IC 480 D310...
Page 66: Printed Wiring Board - Main Section (Side B)
RCD-W10 6-11. Printed Wiring Board – MAIN Section (Side B) – • : Uses unleaded solder. • See page 53 for Circuit Boards Location. LOADING BOARD S272 LOADING CN151 S271 LOADING M151 (LOADING) IC 800 1-645-721- CN680 (21) C805 • Semiconductor Location Ref.
Page 67: Schematic Diagram - Main Section (1/2)
RCD-W10 6-12. Schematic Diagram – MAIN Section (1/2) – • See page 53 for Waveform. • See page 73 for IC Block Diagrams. • See page 74 for IC Pin Function. CN671 CN630 C100 R107 IC100 BR24C02FV-W IC800 M54641L RB68...
Page 68: Schematic Diagram - Main Section (2/2)
RCD-W10 6-13. Schematic Diagram – MAIN Section (2/2) – CN631 4P(PH) CN660 C465 R461 C460 R462 C463 100k D461 11ES2-TB2 R310 R463 R464 2.2k Q310 D310 2SD2144S-TP-UVW 1SS355 D462 MA8062 R311 RY310 IC310(1/2) R115 NJM4558V TR900 C311 C312 IC460 C113...
Page 69: Printed Wiring Board - Display Section
RCD-W10 6-14. Printed Wiring Board – DISPLAY Section – • : Uses unleaded solder. • See page 53 for Circuit Boards Location. IC 760 IC 781 • Semiconductor Location Ref. No. Location Ref. No. Location D775 Q761 Q762 IC760 Q775...
Page 70: Schematic Diagram - Display Section
RCD-W10 6-15. Schematic Diagram – DISPLAY Section – • See page 73 for IC Block Diagrams. CN700 CN1780 CN710 R1701 S1701 CN921 S921 R791 C791 470p J790 CN920 C921 2200p L799 CN790 WIRE(3P) RV790 R796 C796 20k/20k 470p S723 ENCODER...
Page 71: Ic Block Diagrams
RCD-W10 6-16. IC Block Diagrams IC101 CXD3068Q (BD Board)
Page 72 RCD-W10 IC171 BA5937AFP-E2 (CDR Board) OUT1- SGND OUT1+ OUT4- IN1-1 26 OUT4+ LEVEL SHIFT IN1-2 25 IN4-1 LEVEL SHIFT 24 IN4-2 23 VREFIN MUTE MUTE 22 VCC1 ch1,4 VCC3 LEVEL SHIFT VCC2 VCC(ch2) LDIN OUT3+ OUT2+ OUT3- VOLTAGE OUT2- CTRL...
Page 73 RCD-W10 IC500 CXD9692R (MAIN Board) 33 R-OUT TST2 L-OUT A_LRCK D_LRCK A_BICK D_BICK DATT DATT IPGA A_DATA D_DATA VCOM SMUTE A_MCLK D_MCLK S_LRCK AUDIO S_BICK INTERFACE S_DATAI PDOWN 29 M/S S_DATAO R_LRCK T_LRCK INT0 LRCK R_BICK T_BICK R_DATA T_DATA R_MCLK...
Page 74: Ic Pin Function Description
RCD-W10 6-17. IC Pin Function Description • IC1 µPD70F3033AYGF-M02-3BA CD & SYSTEM CONTROL (MAIN Board) Pin No. Pin Name Description FL-LD-DT Data output to the FL driver FL-LD-CLK Clock output to the FL driver DA-DATA-IN Data input from the AD/DA converter (IC500)
Page 75 RCD-W10 Pin No. Pin Name Description OUT_SW Tray open/close detection switch signal input IN_SW Tray open/close detection switch signal input LOD_POS Loading motor control signal output LOD_NEG Loading motor control signal output CLP_POS Elevator up/down motor control signal output Not used...
Page 76 RCD-W10 • IC101 AK8567 S/H & MATRIX, MPX (CDR Board) Pin No. Pin Name Description AVDD3 — Power supply (analog) BCENT Center signal output β signal top level signal output PHBETA β signal bottom level signal output BHBETA PHBTC Extrenal capacitor teminal for PHBETA droop rate setting...
Page 77 RCD-W10 Pin No. Pin Name Description DVDD — Power supply (digital) FOK signal output RF zero cross detection signal output Not used (open) MPDSH Sampling pulse input for main beam signal “H” : sample, “L” : hold SPDSH Sampling pulse input for side beam signal “H” : sample, “L” : hold RFPDSH Sampling pulse input for read APC “H”...
Page 78 RCD-W10 • IC201 LC89587-UK1-E CD DEC/ENC (CDR Board) Pin No. Pin Name Description DVSS — Ground terminal (digital) 2 to 6 RA4 to RA8 Address signal output to the buffer RAM for audio data delay Address signal output to the buffer RAM for audio data delay Not used (open) DVDD —...
Page 79 RCD-W10 Pin No. Pin Name Description DVDD — Power supply +5V (digital) DVSS — Ground terminal (digital) DVDD — Power supply +3.3V (digital) DVSS — Ground terminal (digital) AVDD — Power supply +3.3V (analog) for slice level setting AVSS —...
Page 80 RCD-W10 Pin No. Pin Name Description DVSS — Ground terminal (digital) ATIPSYNC ATIP sync signal output BIDATA ATIP demodulator input/output (fixed at “L”) BICLK ATIP demodulator input/output (fixed at “L”) WOBBLE ATIP demodulator input/output JITERR Clock jitter suppressor error signal output Not used (open)
Page 81 RCD-W10 Pin No. Pin Name Description DVDD — Power supply +5V (digital) DVSS — Ground terminal (digital) ADCSTBY ADC standby signal output AUXTX DIT data input Not used (fixed at “L”) DITOUT DIT data output TEST3 Used as EXTDACEMP input (fixed at “L”) SBDATA Sub-code I/F serial data input/output (fixed at “L”)
Page 82 RCD-W10 HD64F3064BFBL25 µCOM (CDR Board) • IC501 Pin No. Pin Name Description — Capacitor connection terminal for the internal power supply XCSCDR Chip select signal output to the IC201 3 to 5 — Not used (fixed at “H”) XRSTRFP Register reset signal output to the IC101...
Page 83 RCD-W10 Pin No. Pin Name Description BCENT Center signal input from the IC101 β signal top level signal input from the IC101 PHBETA β signal bottom level signal input from the IC101 BHBETA VREF Reference voltage input terminal Monitor multiplexer signal input from the IC101...
Page 84: Exploded Views
RCD-W10 SECTION 7 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one. in the exploded views are not supplied.
Page 85: Front Panel Section
RCD-W10 7-2. Front Panel Section supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4954-532-1 PANEL ASSY, FRONT 3-931-378-51 KNOB (F10) 4-977-358-11 CUSHION 1-683-868-11 HP BOARD 4-238-396-11 KNOB (AMS) 1-685-605-11 CD-EJECT BOARD 4-238-396-01 KNOB (AMS)
Page 86: Chassis Section
RCD-W10 7-3. Chassis Section CD mechanism deck section (CDM66C-30B61B) T900 supplied supplied CDR mechanism deck section (CDM65-RBD1) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4953-448-1 FOOT ASSY 4-238-401-51 PANEL, BACK (US) 4-977-358-11 CUSHION 4-238-401-61 PANEL, BACK (CND) 4-232-237-01 FOOT (DIA.
Page 87: Cdr Mechanism Deck Section (Cdm65-Rbd1)
RCD-W10 7-4. CDR Mechanism Deck Section (CDM65-RBD1) supplied supplied M201 not supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-823-651-11 CABLE, FLEXIBLE FLAT (32 CORE) 4-999-537-01 BELT (LOADING) 4-237-168-01 SCREW, STEP 4-237-176-02 PULLEY (CG)
Page 88: Cd Mechanism Deck Section (Cdm66C-30B61B)
RCD-W10 7-5. CD Mechanism Deck Section (CDM66C-30B61B) supplied M151 base unit section (BU-30BBD61B) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-238-370-02 LEVER (SW) X-4954-474-1 PULLEY ASSY, CHUCKING 4-238-371-01 LEVER (STP) A-4604-363-A MOTOR (L) ASSY (LOADING)
Page 89: Base Unit Section (Bu-30Bbd61B)
RCD-W10 7-6. Base Unit Section (BU-30BBD61B) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-4727-463-A BD BOARD, COMPLETE A-4735-885-A BU-30B ASSY 1-782-817-11 WIRE (FLAT TYPE) (16 CORE)
Page 90: Electrical Parts List
RCD-W10 SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS • Abbreviation parts list may be different from the parts All resistors are in ohms. CND : Canadian model specified in the diagrams or the components METAL: metal-film resistor used on the set.
Page 91 RCD-W10 CD-EJECT Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > < VARIABLE RESISTOR > R102 1-216-835-11 METAL CHIP 1/16W RV101 1-223-997-21 RES, CARBON ADJ VAR 47K R103 1-216-845-11 METAL CHIP 100K 1/16W R104...
Page 92 RCD-W10 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C135 1-162-959-11 CERAMIC CHIP 330PF C224 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C136 1-126-391-11 ELECT CHIP 47uF 20.00% 6.3V C225 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C226 1-107-826-11 CERAMIC CHIP 0.1uF...
Page 93 RCD-W10 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C521 1-164-156-11 CERAMIC CHIP 0.1uF < TRANSISTOR > C526 1-164-156-11 CERAMIC CHIP 0.1uF Q170 8-729-900-53 TRANSISTOR DTC114EKA-T146 < CONNECTOR > Q501 8-729-900-53 TRANSISTOR DTC114EKA-T146 CN101 1-784-894-11 CONNECTOR, FFC/FPC 32P <...
Page 94 RCD-W10 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R192 1-216-864-11 METAL CHIP 1/16W R269 1-216-817-11 METAL CHIP 1/16W R193 1-220-810-11 RES-CHIP 0.39 1/2W R270 1-218-847-11 METAL CHIP 0.5% 1/10W R194 1-216-864-11 METAL CHIP 1/16W R271 1-218-865-11 METAL CHIP 5.6K...
Page 95 RCD-W10 CD-SW DISPLAY Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R533 1-216-864-11 METAL CHIP 1/16W < RESISTOR > R534 1-216-829-11 METAL CHIP 4.7K 1/16W R725 1-249-417-11 CARBON 1/4W F R535 1-216-864-11 METAL CHIP 1/16W R726 1-249-419-11 CARBON 1.5K...
Page 96 RCD-W10 DISPLAY LOADING MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > 1-683-868-11 HP BOARD ********* R701 1-249-409-11 CARBON 1/4W F R702 1-249-411-11 CARBON 1/4W < CAPACITOR > R703 1-249-413-11 CARBON 1/4W F...
Page 97 RCD-W10 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C211 1-136-356-11 MYLAR 470PF 5.00% 50V C621 1-164-156-11 CERAMIC CHIP 0.1uF C630 1-216-864-11 METAL CHIP 1/16W C212 1-128-551-11 ELECT 22uF 20.00% 25V C670 1-164-156-11 CERAMIC CHIP 0.1uF...
Page 98 RCD-W10 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks IC440 8-759-605-00 IC AN7807 R113 1-216-849-11 METAL CHIP 220K 1/16W IC450 8-759-400-66 IC AN7808 R115 1-216-805-11 METAL CHIP 1/16W R170 1-216-845-11 METAL CHIP 100K 1/16W IC460...
Page 99 RCD-W10 MAIN POWER-SW Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R544 1-216-864-11 METAL CHIP 1/16W MISCELLANEOUS R550 1-216-864-11 METAL CHIP 1/16W ************** R611 1-216-817-11 METAL CHIP 1/16W 1-783-531-32 CORD, POWER (CND) R636 1-216-864-11 METAL CHIP...
Page 100 RCD-W10 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2002.09...

Sony RCD-W10 Service Manual

1 Servicing Note

2 General

3 Disassembly

4 Test Mode

5 Electrical Adjustments

6 Diagrams

7 Exploded Views

8 Electrical Parts List

Quick Links

Related Manuals for Sony RCD-W10

Summary of Contents for Sony RCD-W10

Table of Contents