Advertisement
C
D
M
A
HAIN
IALING FROM
EMORY
CCESSING THE
Use this feature to make calls which require a sequence of numbers, for instance if you
PHONE
use a calling card for a frequently called long distance number. The following example
You can access your answering machine from a touch-tone phone by entering your 3-
shows how you can use chain dialing to make a call through a long distance service:
digit security code after you hear the outgoing announcement.
The Number For
Memory Location
1. Dial the phone number for the answering machine.
2. Enter the security code after you hear the tone.
Long distance access number
7
3. Follow the voice menu to use the answerer's remote functions.
Authorization code
8
The remote feature enables you to perform the following functions:
Frequently called long distance number
9
To
1. Make sure the phone is ON.
Review message
2. Press MEM and then press 7.
Play back messages
3. When you hear the access tone, press MEM and then press 8.
Stop message playback
4. At the next access tone, press MEM and then 9.
Erase message
TIP: Don't get in too big of a hurry. Wait for the access tones before pressing the next
memory button, or your call might not go through.
Skip message
Turn off answerer
T
T
EMPORARY
ONE
Review voice menu options
This feature enables pulse (rotary) service phone users to access touch-tone services
offered by banks, credit card companies, etc. Press the TONE button to temporarily
TIP: You can bypass the outgoing announcement by pressing any numbered key on the
make the phone touch-tone compatible. To get information about your bank account,
keypad while the announcement is playing. Then, you can enter your security code to
for example, you would:
access the answering machine.
1. Call the bank's information line.
2. Press the TONE key, denoted with (*) on the keypad, when your call is answered.
C
HANGING THE
3. Follow the voice menu instructions to get the information. When you hang up, the
phone goes back to pulse (rotary) service.
The default security code for accessing the answerer from another location is 1 2 3.
You must use the handset to change the security code. With the phone off, follow
R
A
EMOTE
CCESS
these steps:
1. Press ANSWER (the ANS. indicator comes on).
This section explains two types of remote access: using the handset to access the
answering machine and accessing the answering machine from another phone.
2. Press TONE (*).
3. Enter 3 numbers to be used as the new security code.
The handset contains integrated buttons that enable you access the answering
machine with the handset.
4. Press TONE (*) again.
You can also access your answering machine from any phone that is tone-dial
C
HANGING THE
compatible by entering a 3-digit security code after you hear the outgoing
announcement. A voice menu system guides you through all of the procedures.
Make sure the telephone is OFF before you replace battery.
1. Remove the battery compartment door.
U
H
SING THE
ANDSET
2. Disconnect the cord attached to the battery pack and remove
Press the ANSWER button to access the answering machine from the cordless
the battery pack from the handset.
handset.
3. Insert the new battery pack and connect the cord to the jack
After you access the answerer, use the marked handset keys just as if you were
inside the handset.
pressing the corresponding buttons on the base (see "Answering Machine Operation"
4. Put the battery compartment door back on.
for details on functions). To make it easy for you, the functions are listed on the handset
5. Place handset in the base to charge.
above each number. For example, to play messages:
Allow the handset battery to properly charge (for 12 hours)
1. Press the ANSWER button.
prior to first use or when you install a new battery pack. If
2. Press 2 (PLAY/STOP).
you don't properly charge the phone, battery performance will
be compromised.
3. When you are finished listening to your messages, press ANSWER again.
A
I
NSWERER
NDICATOR
CAUTION: To reduce the risk of fire or personal injury, use only the battery
You know the answerer is being accessed by the handset when the ANS. indicator
listed in the instruction book.
comes on.
B
S
C
H
ATTERY
CREENING
ALLS FROM THE
ANDSET
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type,
Use the handset to screen calls even when you can't hear the answering machine.
toxic materials could be released which can cause injury.
When the phone rings:
• To reduce the risk of fire or personal injury, use only the battery listed in the
1. Press the ANSWER button to gain access to the answering machine.
User's Guide.
2. Listen to the caller leaving a message.
• Keep batteries out of the reach of children.
3. Press the TALK button to talk to the person or press ANSWER to stop
• Remove batteries if storing over 30 days.
screening the call.
M
F
EMORY
ULL
When the memory is full, the system answers after 10 rings, beeps and waits for the
caller to enter the 3-digit security code. If you don't enter the security code within 10
seconds after the unit beeps, the phone hangs up.
You need to erase some of the messages in order for the system to record new
incoming messages.
NOTE: The unit also answers after the 10th ring if it is turned off. To access the answerer
from another location, enter your 3-digit security code after you hear the beep.
A
T
NSWERER FROM ANOTHER
ROUBLESHOOTING
C
P
ORDLESS
HONE
Problem
No dial tone
Press this Button
1
2
2
0 (during message
playback)
3
4
7
Handset does not ring
S
C
ECURITY
ODE
You experience static,
noise, or fading in and out
B
ATTERY
Unit beeps
Memory Dialing
doesn't work
A
M
NSWERING
ACHINE
Problem
Can't hear messages,
beep, etc.
Time/Day setting
S
P
AFETY
RECAUTIONS
stuck at 12 a.m Mon.
Answers on 10th ring
Incoming messages
are incomplete
Won't respond to
NOTE: The RBRC seal on the battery used in your ATLINKS USA product
remote commands
indicates that we are participating in a program to collect and recycle
Nickel Cadmium batteries throughout the United States. Please call 1-800-8-
BATTERY for information or contact your local recycling center.
G
H
S
S
UIDE
ANDSET
OUND
IGNALS
S
OLUTIONS
Signal
Solution
Three long beeps
A long warbling tone (with ringer on)
•
Check installation:
— Is the base power cord connected to
One short beep every few seconds
a working outlet?
— Is the CHARGE indicator on?
A
S
I
— Is the telephone line cord connected
NSWER
TATUS
NDICATORS
to wall jack?
•
Connect another phone to the same
The following indicators show the status of the answerer.
jack; the problem might be your wiring
0-59
Total number of messages.
or local service.
•
Is the handset out of range of the base?
CL (blinking)
The voice time/day stamp needs set.
•
Make sure the battery is properly
charged (12 hours).
- -
Answerer off.
•
Is the battery pack installed correctly?
•
Did the handset beep when you pressed
An (blinking)
Currently answering a call.
the TALK button? Did the IN-USE
indicator come on? The battery may
F (blinking)
Memory is full.
need to be charged.
Six bars (blinking)
Recording a memo or announcement.
•
Place the handset in the base for at least
20 seconds.
C
P
R
AUSES OF
OOR
ECEPTION
•
Make sure the RINGER switch on the
handset is turned to ON.
• Aluminum siding
•
Move closer to the base. The handset
• Foil backing on insulation
may be out of range.
• Heating ducts and other metal construction that can shield radio signals.
•
You may have too many extension
• You're too close to appliances such as microwaves, stoves,
phones on your line. Try unplugging
computers, etc.
some phones.
•
Check for dial tone.
• Atmospheric conditions, such as strong storms
• Base is installed in the basement or lower floor of the house.
•
Change channels.
• Base is plugged into AC outlet with other electronic devices.
•
Move closer to base (handset might be
out of range).
• Baby monitor is using the same frequency.
•
Does the base need to be relocated?
• Handset battery is low.
Make sure base is not plugged into an
• You're out of range of the base.
outlet with another household
appliance.
G
P
C
ENERAL
RODUCT
•
Charge battery.
•
Place handset in base for 20 seconds; if
To keep your telephone working and looking good, follow these guidelines:
it still beeps, charge battery for 12
• Avoid putting the phone near heating appliances and devices that generate
hours.
electrical noise (for example, motors or fluorescent lamps).
•
Clean charging contacts on handset and
base with a soft cloth, or an eraser.
• DO NOT expose to direct sunlight or moisture.
•
See solutions for "No dial tone. "
• Avoid dropping the handset, as well as other rough treatment to the phone.
•
Replace battery.
• Clean the unit with a soft cloth.
•
Did you program the memory location
• Never use a strong cleaning agent or abrasive powder because this will damage the
keys
finish.
correctly?
• Retain the original packaging in case you need to ship the phone at a later date.
•
Did you follow proper dialing sequence?
• Periodically clean the charge contacts on the handset and base with a soft cloth
S
S
OLUTIONS
ERVICE
Solution
FCC requires this product be serviced only by the manufacturer or its authorized
service agents. In accordance with FCC requirements, changes or modifications not
•
Adjust speaker volume.
expressly approved by ATLINKS USA, Inc. could void the user's authority to operate
this product. For instructions on how to obtain service, refer to the warranty included in
•
Set the time clock.
this guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
ATLINKS USA, Inc.
•
Make sure answerer is turned on.
Manager, Consumer Relations
•
Memory may be full.
P O Box 1976
•
Was an extension phone picked up?
Indianapolis, IN 46206
•
Memory is full.
Attach your sales receipt to the booklet for future reference or jot down the date this
•
Accidentally pressed PLAY button
product was purchased or received as a gift. This information will be valuable if
during playback and stopped message.
service should be required during the warranty period.
•
Must use tone-dial phone.
Purchase date ________________________________________________
•
Must enter correct security code.
•
Did unit hang up? If you take no action
Name of store ________________________________________________
for a period of time, it automatically
hangs up.
L
W
IMITED
ARRANTY
What your warranty covers:
Meaning
• Defects in materials or workmanship.
Page signal
For how long after your purchase:
• One year, from date of purchase.
Incoming call signal
(The warranty period for rental units begins with the first rental or 45 days from date
Battery low
of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The exchange unit is
under warranty for the remainder of the original product's warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were originally provided
with the product. We recommend using the original carton and packing materials.
• "Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the product is within the warranty period, must be presented to obtain
warranty service." For rental firms, proof of first rental is also required. Also print
your name and address and a description of the defect. Send via standard UPS or its
equivalent to:
ATLINKS USA, Inc.
c/o Thomson multimedia Inc.
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by
the warranty.
• Insure your shipment for loss or damage. Atlinks accepts no liability in case of
damage or loss.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner's Manual provides information regarding
operating instructions and user controls. Any additional information, should be
obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
ARE
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit. It
will make it easier to contact you should it ever be necessary. The return of the card
is not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A
GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights
that vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
DESCRIPTION
CATALOG NUMBER PRICE* QUANTITY TOTAL
To order, call 1-800-338-0376 (for accessories only) or complete this order form.
Advertisement
