Listening To The Radio; Presetting Stations Automatically; Listening/Confirming The Preset Channels; Manual Tuning - Panasonic S-XH55 Operating Instructions Manual

Listening to the radio

Presetting stations automatically

Up to 30 stations can be set.
1
Press [RADIO]4 to select "FM".
2
Press [MENU]C.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
CURRENT:
To begin auto preset with the current frequency.
§ To change the frequency, refer to "Manual tuning" (
3
Press and hold [OK]8.
Release the button when "FM AUTO" is displayed.
The tuner starts to preset all the stations it can receive into the
channels in ascending order.
≥ "SET OK" is displayed when the stations are set, and the radio tunes to
the last preset station.
≥ "ERROR" is displayed when auto presetting is unsuccessful. Preset the
stations manually ( below).

Listening/confirming the preset channels

1
Press [RADIO]4 to select "FM".
2
Press the numbered buttons to select a channel.
≥ To select a 2-digit number
e.g. 12: [S10]2
Alternatively, press [X, W]@.
≥ The FM setting is also shown on the TV display.
If noise is excessive
Press and hold [PLAY MODE]9 to display "MONO".
To cancel the mode, press and hold the button again until "AUTO ST" is
displayed.
≥ The mode is also cancelled when you change the frequency.

Manual tuning

1
Press [RADIO]4 to select "FM".
2
Press [SEARCH6, SEARCH5]? to select the
frequency.
≥ To start auto tuning, press and hold [SEARCH6,
SEARCH5]? until the frequency starts scrolling. Tuning stops
when a station is found.
Presetting stations manually
Up to 30 stations can be set.
1 While listening to the radio broadcast
Press [OK]8.
2 While the frequency is flashing on the display
Press the numbered buttons to select a channel.
≥ To select a 2-digit number
e.g. 12: [S10]2 [1]
Alternatively, press [X, W]@, and then press [OK]8.
A station previously stored is overwritten when another station is stored in
the same channel preset.
10
§
[1] [2]
[2]

Using the START menu

You can select desired source, change the settings, access playback/
menus, etc., by using the START menu.
1
Press [START]B to show the START menu.
≥ When using VIERA Link "HDAVI Control", the TV also turns on
when the START menu is displayed.
e.g.
below).
2
Press [3, 4]8 to select an item and press [OK]8.
≥ To exit, press [START]B.
3
Press [3, 4, 2, 1]8 to make the setting and press
[OK]8.
When "Input Selection" is selected
You can select a desired source from the menu.
≥ DVD/CD ( 12), FM RADIO (
( below), USB (
§ "(TV)" will appear beside "AUX" or "ARC", indicating the TV audio
setting for VIERA Link "HDAVI Control" (
When "Setup" is selected
You can change the settings for this unit. (
Other selectable items
The items that are displayed will vary depending on the media and
source.
When a disc is loaded or an USB device is connected, you can also
access playback or menus from the START menu.
e.g. [DVD-V]
DVD/CD
When the on-screen control panel appears
e.g. [DVD-V] (when "Playback Disc" is selected from the START menu)
You can operate the playback with the indicated controls.

Selecting the source using the remote control

Press To select
[DVD]4 DVD/CD
[RADIO]4 FM (
[EXT-IN]4 Each time you press the button:
AUX:
ARC:
USB:
Confirm the audio connection to the AUX or HDMI AV OUT terminal on the
main unit when you select the corresponding sources (
volume on the TV to its minimum, and then adjust the volume of the main unit.
D V D / C D H o m e C i n e m a
Input Selection
Setup
left), AUX (
§
16)
15).
16)
Home Cinema
P l a y b a c k D i s c
TOP MENU(DVD)
MENU(DVD)
Input Selection
Setup
left)
For audio input through the AUX terminal.
For audio input through the HDMI AV OUT terminal.
( 16)
below), ARC
§
Playback/menu access
8). Reduce the