Remote Control; General Operation - Sanyo DC-DA2000 Instruction Manual

Controls
/ON
1
1
2
5
9
3
4
5
n
SOUND
6
d
7
1. Power button (z/ON)
2. Number buttons (1-9, 0)
3. Volume buttons (VOLUME +, -)
4. Memory button (MEMORY)
5. CD player controls
REPEAT: Repeat button
n: Stop button
f, e: Skip/Search buttons (These buttons can also be use as
tuning buttons)
i: Play/Pause button
6. Sound preset button (SOUND)
7. Cassette deck controls :
n: Stop button
a: play button
d: Rewind button
c: Fast forward button
r: Record muting button
j: Record/Record pause button
8. Preset button (PRESET)
9. Tuner function/Band select button (TUNER/BAND)
10. Function button (FUNCTION)
11. FM mode button (FM MODE)
Turning the power on and off
Before use, be sure to press the AC power
button (rear of the unit) to "Z STANDBY". If
the unit is not to be used for a long period of
time, press the button again to "Y OFF".
To turn the power on, press the z/ON button on the front panel, the
STANDBY indicator goes out, and the display lights.
To turn the power off, press the z/ON again, the STANDBY indicator
lights and the display goes out.
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when
the z/ON button is set to the z position.
Selecting the function
Press the FUNCTION button to select the desired function as follows
display shows.
Cd v TAPE v TU v LInE v Cd v ...
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.

REMOTE CONTROL

11
FM MODE FUNCTION
10
2 3 4
6 7 8
TUNER 9
0 PRESET
/BAND
8
VOLUME
MEMORY REPEAT
CD
i
f e
- TUNE +
STOP PLAY
n a
REC MUTE
r c
REC/PAUSE
j
TAPE

GENERAL OPERATION

STANDBY
Z
Number buttons (1-9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is "CD", the buttons select the track numbers on a disc.
If the function is "TUNER", the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
1
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
Remote sensor
Within approx.
7 meters
Adjusting the volume
OFF
Turn the VOLUME control, (or press the + or - VOLUME button on the
Y
remote control). The volume level appears on the display. (VOL 0 ~ VOL
40)
Surround sound button
Press the SURROUND button, "SURR" appears on the display and a 3
dimensional sound effect is created.
Bass expander button
Press the BASS button to enhance the bass sound.
"BASS" appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
CLASSIC: Classical music, etc.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the i button on the unit for at least 60 seconds.
3. Connect the mains lead.
4. Operate the unit.
-3-
2
Two R03/HP16 batteries
(not supplied)
CD
TAPE