Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DW433-XE
Summary of Contents for DeWalt DW433-XE
- Page 1 INSTRUCTION MANUAL DW433-XE VARIABLE SPEED BELT SANDER 75 mm x 533 mm (3" x 21")
-
Page 3: Definitions: Safety Guidelines
CALL US AT: 1800 444 224 (Aust) or 0800 339 258 (NZ). period. Technical Data Identify additional safety measures to protect the operator from the effects of DW433-XE vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. Voltage... -
Page 4: Work Area Safety
SAVE ALL WARNINGS AND INSTRUCTIONS FOR under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. FUTURE REFERENCE b) Use personal protective equipment. Always wear eye protection. Protective The term “power tool”... -
Page 5: Extension Cords
Additional Specific Safety Instructions for Sanders e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s • Hold power tools by insulated gripping surfaces when performing an operation operation. -
Page 6: Precautions To Take When Sanding Paint
• Avoid prolonged contact with dust from power sanding, sawing, grinding, b. A dust mask or respirator should be worn by all persons entering the work area. drilling, and other construction activities. Wear protective clothing and wash The filter should be replaced daily or whenever the wearer has difficulty breathing. exposed areas with soap and water. -
Page 7: Intended Use
COMPONENTS (Fig. 1, 2) INTENDED USE This variable speed belt sander is designed for professional sanding applications. WARNING: Never modify the power tool or any part of it. Damage or personal DO NOT use under wet conditions or in presence of flammable liquids or gases. injury could result. -
Page 8: Operation
Replacing the Sanding Belt Switch Operation • To start the belt sander, depress the trigger switch (D). Allow the belt sander to TO REMOVE SANDING BELT (FIG. 1) reach operating speed before touching the work surface (Fig.1). 1. Rotate the belt release lever (A) up until the top front wheel of the sander retracts •... -
Page 9: Proper Hand Position
TO PROPERLY TRACK THE SANDING BELT (FIG. 1) 3. Push the dust collector from the rear of the bag until the ejection chute snaps into the dust chute collar and the locks onto the belt cover (N). 1. Grasp the rear handle (H) of the unit firmly and flip the sander so that the belt is facing the operator. - Page 10 An accidental start-up can cause injury. Two accessories are offered for your D Walt belt sander, DW433-XE, at extra cost from your local service centre. They are the DW4050-Vacuum Adapter and DW4055- Integrated Sanding Frame and Inversion Stand.
-
Page 11: Maintenance
To Remove the Brushes FIG. 10 WARNING: If the belt sander in the The brushes on your belt sander may require replacement at some point during the inversion stand is in the horizontal life of the tool. Contact your local D Walt authorized service centre to obtain additional position, be sure guard (Y) is covering brushes. - Page 12 Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by certified service centres or other qualified service organizations, always using identical replacement parts. Accessories WARNING: Since accessories, other than those offered by D WALT, have not been tested with this product, use of such accessories with this tool could be hazardous.
- Page 16 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (MAR12) Part No. N173928 DW433-XE Copyright © 2003, 2004, 2005, 2012 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...