NEC MultiSync LCD195WXM User Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Monitor
  5. MultiSync LCD195WXM
  6. User manual
NEC MultiSync LCD195WXM User Manual

NEC MultiSync LCD195WXM User Manual

Nec monitor user's manual
Hide thumbs Also See for MultiSync LCD195WXM:
Table of Contents

Advertisement

Quick Links

See also: User Manual
MultiSync LCD195WXM
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for NEC MultiSync LCD195WXM

Summary of Contents for NEC MultiSync LCD195WXM

  • Page 1 MultiSync LCD195WXM User’s Manual...

  • Page 2: Declaration Of The Manufacturer

    Therefore, it should be read carefully in order to avoid any problems. Caution: When operating the MultiSync LCD195WXM with a 220-240V AC power source in Europe, use the power cord provided with the monitor. In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.

  • Page 3: Canadian Department Of Communications Compliance Statement

    Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950-1. FCC Information Use the attached specified cables with the MultiSync LCD195WXM colour monitor so as not to interfere with radio and television reception.

  • Page 4: Quick Start

    Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt base • Audio Cable • Power Cord • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) • Video Signal Cable (DVI-D to DVI-D) •...

  • Page 5: Raise And Lower Monitor Screen

    3. To attach the Cable management cover: Insert the tabs of the Cable management cover into the holes of Stand neck and slide the Cable management cover downward into place (Figure A.4). NOTE: Please confirm that the tabs are completely secure. 4.

  • Page 6: Remove Monitor Stand For Mounting

    Remove Monitor Stand for Mounting To prepare the monitor for alternative mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Figure R.1). 3. Remove the 4 screws connecting the monitor to the stand and remove the stand as indicated (Figure R.2). The monitor is now ready for mounting in an alternative manner.
  • Page 7 Controls OSD (On-Screen-Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key SELECT Button At No OSD Showing OSD. showing At OSD showing Go to Adjustment stage. (Icon selection stage) At OSD showing Go to Icon selection stage.
  • Page 8 AUDIO Control the sound volume of speakers and headphone. To mute the speaker sound, press the 1<->2/RESET key. BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST (Analog Input only) Adjusts the image displayed for non-standard video inputs.

  • Page 9: Monitor Info

    OSD LOCK OUT This control completely locks out access to all OSD control functions without Brightness and Contrast. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are locked out. To activate the OSD Lock Out function, press “1<->2/ RESET”, then “+” key and hold down simultaneously.

  • Page 10: Recommended Use

    As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.

  • Page 12: Specifications

    NOTE: Technical specifications are subject to change without notice. MultiSync LCD195WXM Monitor Horizontal sync. Positive/Negative Vertical sync. Positive/Negative 500mV rms Input Impedance 14 Kohm...
  • Page 13 Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another. Colour Control System: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards.

  • Page 14: Troubleshooting

    As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 15 TCO’03 Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy •...

  • Page 16: Energy Saving

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

This manual is also suitable for:

L195h0

Table of Contents