Table of Contents
Advertisement
ADJUSTING THE CLOCK
The clock display
blinks when the mains
lead is connected
to the AC
5
outlet for the first time.
Example:
To set "7:30PM",
1, Press the CLOCK
switch for 1 or more seconds.
,[
$
C)
K
7':
0
AM
The "CLOCK'
and hours displays
blink.
If nothing further is done, the time setting mode will be released
-
after 30 seconds.
2.
Press the UP and DOWN
switches
to set the "hours."
3.
Press the MEMORY
switch.
The minutes display
blinks.
4.
Press the UP and DOWN
switches
to set the "minutes."
BEFORE OPERATION
Press the POWER
switch.
To turn off the power, press it again.
'iP.OFF"
appears
on the tuner/timer
display for 5 seconds.
The clock display
remains
lit.
When the power is switched ON:
Tuner/Timer:
"Frequency
display"
appears
on the display.
Amplifier:
One of the function indicators
lights. The volume
level will increase to
the previous
level.
CD player:
Ifthefunction
is "CD","-
-" blinks, then "Cd" appears
on the display.
If a disc has been placed
on the disc tray, its total number
of tracks
appears.
— djusting the volume
Press the UP or DOWN
VOLUME
CONTROL
or "+"
or" - " VOL control
on the remote control.
The VOL. level meter shows the volume
set level.
To reduce the volume temporarily
(muting)
Press the MUTE (audio muting) switch on the remote control. [M] appears
on thetuner/timer
display
and the VOL. level meter blinks. (If the volume
level is too low, the VOL. level meter goes out.)
The muting function
will be retained
for a few days, even
if the unit is
turned off or the mains lead is disconnected.
The volume
is restored to its previous
level by pressing
the same switch
again.
Adjusting the left/right speaker
balance
Use the BAIANCE
control to adjust the Ieftlright speaker
balance.
Press the MEMORY
switch. The clock starts.
r
CLOCK
7:30
PM
.J
The time can be set accurately
by pressing
the MEMORY
switch
when a time signal is heard.
These operations
can be done, even if the power is off.
The
UP and DOWN
PRESH/APT
switches
can also be used for
setting the clock.
The clock operation
and memory
are backed
up even with a power
failure lasting 30 seconds
or less.
When
a power failure
lasts for more than 30 seconds,
the memory
contents
will be retained
for several
days but the clock display
will
blink.
Reset the time when the display
blinks
because
of a power
failure.
Reset the timer ON/OFF
times as well.
Adjusting the sound quality
The 5 BAND GRAPHIC
EQUALIZER
controls
(1 OOHz/300Hz/l
kHz/3kHz./
12kHz) allow the sound to be tailored to individual
musical preferences
or
to fit the acoustics
of the room. Moving the control will adjust the sound
level in a narrow range of musical frequencies.
Selecting the function
The function
is automatically
selected
when tape playback
is started, or
when any of the function switches
(except the FM MODE
switch) on the
tuner have been operated.
For CD operation,
press the CD function
switch. If any other function
is
selected,
the CD player will not operate.
When the function selection
is changed,
tape playback
or CD play is
automatically
stopped,
(except during tape dubbing.)
Press the PHONO
or VIDEO
function
switch for turntable
or video
equipment
operation.
Level meter (LEVEL METER)
Shows the amplifier
input levels which are being monitored.
Bass expander system
Press the BASSXPANDER
switch to enhance
the bass sound.
WHAT TO DO IF ...
If the operation
of the unit or display
is not normal, turn off the POWER
switch on the main unit and then turn it on again.
If the power
is not turned
off even
by pressing
the POWER
switch,
disconnect
the mains lead from the AC outlet. Then connect
the lead to
the AC outlet and resume the operation.
In this case, reset the clock and
memory
contents.
-6-
Hide quick links:
Advertisement
Table of Contents
