Table of Contents
Advertisement
Quick Links
The HP 501 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED
n a c
a b
g
802.11a/b/g/n/ac product. The Wi-Fi CERTIFIED Logo is a
certification mark of the Wi-Fi Alliance.
This Quickstart shows you how to install and get started using the HP 501 (J9835A) 802.11ac Wireless Client Bridge, hereafter referred to as the HP 501.
The latest documentation, including the HP 501 802.11ac Wireless Client Bridge Configuration and Administration Guide, is available at www.hp.com/support/
manuals.
Hardware overview
Side view
1: Detachable antennas
2: Mounting bracket
HP 501 802.11ac Wireless Client Bridge Quickstart
1
2
In
3
4
5
3
Front view
3: Power cord cable tie points
4: AC/DC adapter socket
5: Status LEDs (left to right) Power, Ethernet, Radio
6: Ethernet port
7: Console port
8: Reset button
9: Antenna connectors
8
7
6
9
Advertisement
Table of Contents
Related Manuals for HP 501
Summary of Contents for HP 501
-
Page 1: Hardware Overview
HP 501 802.11ac Wireless Client Bridge Quickstart This Quickstart shows you how to install and get started using the HP 501 (J9835A) 802.11ac Wireless Client Bridge, hereafter referred to as the HP 501. The latest documentation, including the HP 501 802.11ac Wireless Client Bridge Configuration and Administration Guide, is available at www.hp.com/support/ manuals. -
Page 2: Package Contents
• An HP 1-Port Power Injector (J9407B). labeled as 8 on page 1. To reset the HP 501, insert a paper clip into the Reset button hole, and press and quickly release the button. To reset the HP 501 to •... -
Page 3: Installation
When mounting the HP 501 on a wall or ceiling, ensure that the surface to discharge or a lightning strike. which you attach the HP 501 and the fasteners you use can support at least 0.9 kg (2 lbs). Allow extra weight for cables. When mounting on a wall or ceiling,... - Page 4 The HP 501 can also be installed on a desktop using the mounting bracket. Slide Hold the mounting bracket against the wall or ceiling where it will be the HP 501 base onto the mounting bracket, and then place it on the desktop in installed. Mark two holes for the screws (wall anchors).
-
Page 5: Initial Configuration
HP 501 to an unused factory-default PoE switch port. • If using a PoE injector, use Ethernet cables to connect your computer to the data-in port of the PoE injector and the HP 501 to the data and power-out port of the PoE injector. - Page 6 SSID directly, be sure to configure the same name as on the private network AP. By default, the HP 501 operates as a DHCP client. This means that if the network has a DHCP server, the HP 501 automatically receives a new IP address in place of its default address of 192.168.1.1 upon connecting to the network.
-
Page 7: Technical Support
Re-launch the HP 501 management tool at https://<IP address> where interference, and 2) this device must accept any interference received, including <IP address> is the IP address that was obtained by the HP 501 from the DHCP interference that may cause undesired operation. -
Page 8: Industry Canada Notice
HP 501 802.11ac Wireless Client Bridge Quickstart Other regulatory information When this device is operated in 5.15~5.25 GHz frequency range, it is restricted The device for the band 5150-5250 MHz is only for indoor usage to reduce the to indoor use only. - Page 9 Product overview тел./факс: +7 (727) 355 35 50, +7 (727) 355 35 51 The HP 501 Wireless Client Bridge can bridge up to 15 Ethernet client devices • HP Russia: ЗАО “Хьюлетт-Паккард А.О.”, running a legacy networking protocol to the WLAN, extending wireless network 125171, Россия, г.
- Page 10 HP 501 802.11ac Wireless Client Bridge Quickstart Other regulatory information Radio Specification Description FCC Part 15.247; EN 300 328; FCC Part 15.407; MIC Notice No. 88, App. 43 & Channel bandwidth 20, 40, and 80 MHz 45; EN 301 893; RSS-210...