1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Laptop
  5. LifeBook S6110
  6. User manual

Fujitsu s6110 User Manual

Hide thumbs Also See for s6110:
Table of Contents

Advertisement

Quick Links

Download this manual
Copyright
Fujitsu Limited has made every effort to ensure the accuracy and completeness of this document. However, as
ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the
accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.
LifeBook is a trademark of Fujitsu Limited.
Microsoft, Windows, MS, MS-DOS, and Windows NT are registered trademarks of the Microsoft Corporation of the
United States in the United States and other countries.
Intel is a registered trademark of the Intel Corporation of the United States.
Macrovision :-
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093
licensed for limited viewing uses only.
Dolby :-
Manufactured under license from Dolby Laboratories. "DOLBY", "PRO LOGIC" and the double-D symbol are
trademarks of Dolby Laboratories. Copyrights 1992-1999 Dolby Laboratories, All rights reserved.
Phoenix is a registered trademark of Phoenix Technologies Corporation of the United States.
K56flex is a trademark of Rockwell International Corporation and Lucent Technologies Corporation.
Other product names are trademarks or registered trademarks of their respective companies.
Other products are copyrighted by their companies.
Copyright© 1981-2001 Microsoft Corporation, All rights reserved.
Copyright© 2001 Phoenix Technologies, Ltd., All rights reserved.
All other products are trademarks or registered trademarks of their respective companies.
Explanations of the adjustments for the track pad cursor control are taken in part from the ALPS GlidePoint Driver
User's Guide, copyright by LCS/Telegraphics in 1996.
© Copyright 2002 Fujitsu Limited. All rights reserved. No part of this publication may be copied, reproduced, or
translated, without the prior written consent of Fujitsu Limited. No part of this publication may be stored or transmitted
in any electronic form without the written consent of Fujitsu Limited.
Wesbite: www.fujitsu-pc-asia.com
DECLARATION OF CONFORMITY
according to FCC Part 15
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device must not be allowed to cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
i

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu s6110

Summary of Contents for Fujitsu s6110

  • Page 1 © Copyright 2002 Fujitsu Limited. All rights reserved. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu Limited. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu Limited.
  • Page 2 CAUTION Changes or modification not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 3 Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu PC Corporation or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.
  • Page 4 Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu PC Corp., ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.
  • Page 5 AVERTISSEMENT Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’é lectricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs ne doivent pas tenter d’é tablir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien.

  • Page 6: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Read these instructions carefully. Save these instructions for future reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water.
  • Page 7 High Safety Required Use This Product is designed, developed and manufactured as contemplated for general use, including without limitation, general office use, personal use, household use and ordinary industrial use, but is not designed,developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury,severe physical damage or other loss (hereinafter ‘High Safety Required Use’), including without limitation, nuclear power reactioncore control in nuclear atomic facility, airplane automatic aircraft...
  • Page 8 Product returned to Fujitsu or its service providers for Warranty Service or other repair, including but not limited to the costs of recovering such programs, data or other information.
  • Page 9 AUSTRALIAN WARNINGS WARNING FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS COMPLIANCE LABEL. THIS INCLUDES CUSTOMER EQUIPMENT PREVIOUSLY LABELLED PERMITTED OR CERTIFIED. Connection of Non Certified/Approved peripherals may result in the equipment operating outside the Australian EMI Standards. Modems connected to the Australian telecommunications network must be operated in accordance with the Labelling Notice.
  • Page 10 NEW ZEALAND WARNINGS The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services.
  • Page 11 Note: Modem setting in Windows 98 / Windows Me The default modem setting in Windows 98 / Windows Me operating system is United States of America. If you are residing in Australia or New Zealand, please choose the appropriate country where you are located.
  • Page 12 Note: Modem setting in Windows XP A. If you are located in Australia 1. Click Start select Control panel select “Phone and Modem Options”. 2. Double click New Location. 3. Choose “Australia” in Country/region pull down menu bar. 4. Select Phone system as “Tone Dialing”. 5.
  • Page 13 NOTATION IN THIS DOCUMENT Warnings This manual uses a variety of icons as visual marks so that you can use this computer safely and correctly and avoid damage and danger to yourself and to others. These icons and their meanings are as follows. Please learn these icons before reading this manual. Learning these icons will be useful for understanding this manual.
  • Page 14 Notation in text Here is what symbols in text mean. Symbol Meaning Critical Point Indicates a point necessary for correctly operating the Critical Points hardware or software. Column Gives the meaning and brief explanation of a term. Column → Indicates the page to see elsewhere in this manual. Command input (key input) Within the text of this manual, command input (giving commands to the computer by pressing keys) is indicated as follows.
  • Page 15 Configuration of this Manual SECTION 1 This section explains basic operations and basic items for using this computer, including the names of the parts and their functions, flat point operation methods, floppy disk unit handing, and battery operation. SECTION 2 This section explains installation of options for this computer.

  • Page 16: Table Of Contents

    CONTENTS SECTION 1 1 Names of the Parts and their Functions ......2 Exterior features: Front/top view ............2 Exterior features: Side view .............. 4 Exterior features: Bottom view of the computer ........ 7 Exterior features: Rear/top view of the computer ......8 Exterior features: Operating Status indicator LCD ......
  • Page 17 9 About the built-in Modem ..........55 10 LifeBook Security/Application Panel ......57 LifeBook Security / Application Panel ..........57 Setting up your LifeBook Security Panel ........57 Passwords ..................58 Operating your LifeBook Security/Application Panel ...... 59 Precautions ..................60 Uninstalling the security Panel Application ........
  • Page 18 SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION 1 1 1 1 1 1 1 1 1 1 This section explains basic operations and basic items for using this computer, including the names of the parts and their functions, Flat point operation methods, floppy disk unit handing, and battery operation.

  • Page 19: Names Of The Parts And Their Functions

    SECTION 1 1 Names of the Parts and their Functions Exterior features: Front/top view (Your computer or situation may not look exactly like this illustration.) LCD panel Displays images output by the computer. Critical Points About the properties of LCD screens The phenomena below are inherent in the properties of LCD screens and do not indicate that LCD screens are faulty.
  • Page 20 LifeBook Security/Application Panel The LifeBook Security/Application Panel provides hardware security and one-touch application launch capability. Power and Suspend/Resume Button The Power and Suspend/Resume button is always used to Power On your LifeBook notebook from its Off state. It is also used as the Suspend/Resume button. This allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on your LifeBook notebook when it has been shut down.

  • Page 21: Exterior Features: Side View

    Exterior features: Side view Right view of the computer Headphone jack/Optical digital audio output terminal • Headphone jack Used to connect commercially available headphones with a f3.5 mini plug. This jack is incompatible with some types of cable connectors, so you should consult a salesperson before purchasing headphones.
  • Page 22 Microphone jack Used to connect a commercially available monaural microphone with a f3.5 mini plug. This jack does not support some types of microphones (e.g., dynamic microphone), so you should consult a salesperson before purchasing a microphone. Air outlet Provide to discharge heat from the computer. When you turn on the computer, the cooling fan rotates for a few seconds.
  • Page 23 Left view of the computer (Your computer or situation may not look exactly like this illustration.) Antitheft lock Used to connect a commercially available antitheft cable. Critical Points The antitheft lock supports Kensington Micro Saver Security System. - When connecting the antitheft lock, you cannot remove the mobile multi-purpose bay unit. Mobile multi-purpose bay Your computer came with an internal optical disk drive, which may vary between countries.Please check with your local distributor for actual configuration.You may change the unit installed in this...

  • Page 24: Exterior Features: Bottom View Of The Computer

    Exterior features: Bottom view of the computer (Your computer or situation may not look exactly like this illustration.) 1. Built-in wireless LAN antenna A wireless LAN antenna is built in here. Expansion RAM module slot Accommodates the memory of your computer. Internal battery pack bay Accommodates an internal battery pack.

  • Page 25: Exterior Features: Rear/Top View Of The Computer

    Exterior features: Rear/top view of computer Modem port Used to connect the computer to a phone line via the supplied modular cable when using a Online service or navigating the Internet. Infrared Port The fast IrDA compatible port allows you to communicate with another IrDA compatible infrared device without a cable.
  • Page 26 IEEE*1394 (DV) port (*: Pronounced “ai triple-e”) Used to connect a peripheral device, such as a digital video camera (DV), to the computer via a DV cable. USB ports Used to connect USB-compliant peripheral devices, such as an optionally available USB floppy disk drive and a USB printer.

  • Page 27: Exterior Features: Operating Status Indicator Lcd

    Exterior features: Operating status indicator LCD Critical Points When you turn off your computer, all indicators on the operating status indicator LCD will go off, except when the battery in your computer is being charged. SUS/RES Indicator ( Lights when the computer is in operation and blinks when it is on standby. AC Adapter Indicator ( Lights when the computer is powered from the AC adapter.
  • Page 28 Hard Disk Access Indicator ( Lights when the hard disk is being accessed. Critical Points To prevent the corruption of data recorded on the hard disk, do not press the power button when the hard disk access indicator is lit. Floppy Disk Drive Access Indicator ( The Floppy Disk Drive Access indicator states whether the floppy disk drive is being accessed.

  • Page 29: Port Replicator

    SECTION 1 2 Port Replicator The port replicator is described here. Port Replicator back panel. Back Panel Components The following is a brief description of the Port Replicator back panel cpmponents. 1. DC Power Jack The DC Power Jack allows you to plug in the AC Adaptor to power on your notebook. 2.
  • Page 30 ❑ Port Replicator front panel. Front Panel Components The following is a brief description of the optional Port Replicator front panel components. 1. Docking Port The docking port connects the Port Replicator to your notebook. IMPORTANT • Certain peripheral devices connected to the port replicator may operate unstably if the port replicator is installed/removed while the PC power is on.

  • Page 31: Installing The Port Replicator

    Installing the Port Replicator This section describes how to install the port replicator. If any peripheral device is connected to the PC rear side, remove it beforehand. CAUTION INJURY • Be careful not to catch your fingers in the space between the PC and the port replicator when installing it.

  • Page 32: Removing The Port Replicator

    Removing the Port Replicator This section describes how to remove the port replicator. If any peripheral device is connected to the port replicator, switch the power off. Release the port replicator lock. Release the lock by sliding the port replicator removal lever. Removal lever Remove the port replicator.

  • Page 33: Pointing Device

    SECTION 1 3 Pointing Device About the Flat Point The Flat Point is a handy pointing device that enables you to move the mouse pointer freely with your finger. It consists of a touch-pad, left and right buttons on this side of the touch-pad, and the scroll button between the left and right buttons.

  • Page 34: How To Use The Flat Point

    How to use the Flat Point • Click “Click” means quickly pressing the left button once or tapping the touch-pad once. Pressing the right button once is called “right-click.” • Double-click “Double-click” means pressing the left button twice in a row or tapping the touch-pad twice in a row.
  • Page 35 Critical Points You can change the functions assigned to the right and left buttons and also adjust the mouse speed, using the Mouse Properties dialog box. To display this dialog box, click the Printers and other hardware icon in the Control Panel window and select Mouse. When tapping the touch-pad, tap it quickly with the tip of a finger but not strongly.

  • Page 36: Keyboard

    SECTION 1 4 Keyboard Keyboard Names and functions of the principal keys Keys that can be used as ten-keys Insert Delete Pause Num Lk Prt Sc SysRq Break Scr Lk < > 17 18 19 Esc (Escape) key Used to cancel the current task and return to the previous task. Function keys Functions assigned to these keys vary from application to application.
  • Page 37 Delete key Used to delete the character on the right of the cursor. With this key, you can also delete the file or icon you selected. By pressing the [ ] key while holding the [ ] and [ ] keys down, you can forcibly terminate the out-of-control application or computer.
  • Page 38 FUNCTION KEYS Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. The [FN] key provides extended functions for the notebook and is always used in conjunction with another key. •...
  • Page 39 End key/Cursor keys Used to move the cursor to the end of the line on which it is currently placed. To do so, press the ] key while holding the [ ] key down. Pressing the [ ] key while holding the [ ] and ] keys down causes the cursor to move to the end of the text.

  • Page 40: Changing The Internal Battery Pack

    SECTION 1 5 Changing the Internal Battery Pack WARNING ELECTRIC SHOCK • Before changing the internal battery pack, be sure to turn off your computer and disconnect the AC adapter from it. To avoid shock hazards and damage to your computer, be careful not to touch internal components of the computer, including the battery connector.
  • Page 41 Install a new battery pack. With the slits in the battery pack aligned with the projections on the computer, place the battery pack in the battery bay and push it down until it clicks into place. Internal battery pack lock IMPORTANT •...

  • Page 42: Running The Computer On Its Battery

    SECTION 1 6 Running the computer on its battery Recharging the battery Connect the AC adapter to your computer. When you connect the AC adapter to your computer, the AC adapter automatically starts to charge the internal battery pack, and the charging status indicator ( ) and the battery life remaining at that time are displayed on the operating status indicator LCD.

  • Page 43: Checking The Remaining Battery Life

    Disconnect the AC adapter from your computer and press the power button. Power button (Your computer or situation may not look exactly like this illustration.) Critical Points The battery runs down in a relatively short time when it is used in a cold place. The chargeability of the battery degrades over time and its life shortens accordingly after it has been used over an extended period of time.

  • Page 44: Low Battery Condition

    Indication of a battery problem Indicates that the battery cannot be charged for some reason or other. Critical Points is displayed, turn off your computer, remove and install the battery all over again. If this persists, your might have to replace the battery pack with a new one because it is most likely defective.
  • Page 45 • Do not take the battery apart. Taking the battery apart or touching its internal components could result in an electric shock or fire. • Electrical discharge – It is good practice to always recharge the battery before use since it is discharged spontaneously.

  • Page 46: Using A Lan

    SECTION 1 7 Using a LAN IMPORTANT • Items you need to set up, such as TCP/IP, for network connections, vary depending on which type of network you want to use: wired LAN or wireless LAN. Set up your computer according to the situation in which you will use your network.

  • Page 47: Connecting A Lan Cable

    Connecting a LAN cable WARNING ELECTRIC SHOCK • Before connecting a LAN cable to your computer, always turn off the computer and disconnect the AC adapter from it to avoid shock hazards. • When it thunders, turn off the computer and disconnect the AC adapter and the LAN cable from it as soon as possible.
  • Page 48 Setting up network connections IMPORTANT • If you have already set up wireless LAN connections, set up network connections with care so that they will not conflict with the wireless LAN connections already set up. A conflict between a wireless LAN connection and a wired LAN connection prevents your computer to carry out communications over your LAN.

  • Page 49: About The Integrated Wireless Lan (For Selected Model)

    (For selected model) Before Using This Device Thank you for purchasing a Fujitsu LifeBook with an Integrated Wireless LAN. This manual describes the basic operating procedures for the Wireless LAN (referred to as the “device” in this manual) and how to set up a wireless LAN network. Before using this device, read this manual carefully to ensure correct operation of the device.
  • Page 50 How to Handle This Device The Integrated Wireless LAN device is already installed in your LifeBook computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The LAN has been configured to support the operating system with which your system shipped. Critical Points The default BIOS setting for Wireless LAN is disabled.

  • Page 51: Connecting Windows 2000 Systems

    SECTION 1 Connecting Windows 2000 Systems This chapter describes how to set the wireless LAN connection for computers running Windows 2000. Critical Points When you receive your LifeBook, the integrated wireless LAN device and drivers have already been installed. This procedure outlines the steps for setting the device parameters. Workflow The proper setup of the wireless LAN requires several steps which must be performed in the proper order.
  • Page 52 Set the encryption items in accordance with Table 2. • AdHoc Network: Specify the same value for all the computers for which the encryption key is used for connection. • Infrastructure Network: Specify the identical encryption keys to the encryption keys set for the access point.
  • Page 53 When you finish your entry, click [Apply]. Click [OK]. [PRISM Wireless Settings] closes. You have completed the parameter settings. Critical Points When you are using ADSL (PPPoE) with the infrastructure network to connect to the Internet, you need to change the MTU size set for the computer. To change the MTU size, refer to the manual that comes with the access point.

  • Page 54: Network Connection

    Network Connection The section describes how to set the network connection for a computer with Windows 2000. Network Settings In this section, you set “TCP/IP Settings,” and complete Double-click the [Network and Dial-up Connections] icon. The [Network and Dial-up Connections] window appears. Right click the [Local Area Connection], then click [Properties] from the menu that appears.
  • Page 55 Checking the full computer name and workgroup Click [Start] → 2 [Settings] → 3 [Control Panel]. Check [Full computer name] and [Workgroup]. Ask your network administrator and check the setting. Item Description Full A name to identify the computer on the network. You can specify any name Computer to each computer.

  • Page 56: Sharing

    Sharing In this section, you set sharing of the drive, folder, and printer. You only need to set this when you are sharing files or a printer with other computers on the network. When you share a drive, folder, or printer, you can use them from any computer on the network. Setting [File and Printer Sharing for Microsoft Networks] Click [Start] →...
  • Page 57 Sharing Files The following example shows how to set sharing the “ Work” folder on the c: drive. On the desktop, double-click [My Computer] → C: drive. Right-click the “ Work” folder, then click [Sharing] from the menu. The [Work Properties] window appears.

  • Page 58: Checking The Connection

    Checking the Connection After the network setting is completed, access the shared drive on another computer to check the connectivity of the wireless LAN network. Accessing Another Computer Double-click the [My Network Places] icon on the desktop. [My Network Places] appears. Double-click [Computers near me].

  • Page 59: Connecting Windows Xp Systems

    SECTION 1 Connecting Windows XP Systems This chapter describes how to set up the wireless LAN connection for computers that are running Windows XP. Critical Points When you receive your LifeBook, the integrated wireless LAN device and drivers have already been installed.

  • Page 60: Network Connection

    Critical Points Be sure to specify the encryption keys. If you do not specify the keys, any computer with a wireless LAN card can be connected. This presents a risk that other users may steal or destroy your data. Description Item Enter the network name to which you want to connect.
  • Page 61 Critical Points If [Wireless Network Connection 2 Properties] is not displayed, click [Start] → [Settings] → [Control Panel], and double-click the [Network Connection] icon. Right click the [Wireless Network Connection], and then click [Properties] from the menu that appears. Perform the following steps. •...

  • Page 62: Sharing

    Item Description Computer A name to identify the computer on the network. You can specify any name Name to each computer. Use up to 15 single-byte characters. For easier identification, use the model name or user name. A name of the network group. Use up to 15 single-byte characters. Workgroup AdHoc Network : Specify the same name to all computers within the same network.
  • Page 63 Sharing Files The following example shows how to set sharing the “ Work” folder on the c: drive. Click [Start] → [My Computer]. Double-click the [Local Disk (c:)] icon. Right click the “ Work” folder, and then click [Sharing and Security] from the menu that appears.

  • Page 64: Checking The Connection

    Checking the Connection After the network setting is completed, access the shared drive on another computer to check the connectivity of the wireless LAN network. Accessing Another Computer Click [Start] → [My Computer]. From the left menu in [Other Places], click [My Network Places]. From the left menu in [Network Tasks], click [View workgroup computers].

  • Page 65: Troubleshooting

    SECTION 1 Troubleshooting This chapter contains troubleshooting information, including causes and actions, for problems you may find while using this device. Troubleshooting Table Problem Possible Cause Possible Solution An exclamation mark (!) A failure to recognize the Restart the computer. or cross (x) is attached device.
  • Page 66 Problem Possible Solution Possible Cause Other computers If the TCP/IP protocol is installed, do the The TCP/IP protocol is are not displayed when following to check the IP address: not installed, or, the IP the [Network Computer] address is not set 1.
  • Page 67 Problem Possible Solution Possible Cause IP packet isn’t reaching Perform the following steps to run the PING Run the PING command command to check if the IP packet is correctly its destination to check the connection delivered to the destination. To run the PING command, the TCP/IP protocol must be installed.
  • Page 68 Problem Possible Solution Possible Cause Cannot connect to The following causes are possible. Check There are several each one of them. the network possible causes, • The network name or encryption key is not right. as listed to the right. •...
  • Page 69 Problem Possible Solution Possible Cause I want to remove the Windows XP: driver When removing the driver, make sure (Windows XP) that the device is attached to the computer. If you try to remove the driver while the device is detached from the computer, the driver is not removed.

  • Page 70: About Ip Addresses

    SECTION 1 About IP Addresses SETTING IP ADDRESSES If you are not sure how to set the IP address, refer to the following procedure. If you have an access point (DHCP server) on the network, set the IP address as follows: Windows 2000: [Obtain an IP address automatically] Windows XP: [Obtain an IP address automatically] Critical Points...

  • Page 71: Specifications

    SECTION 1 Specifications Technical Specifications for Integrated Wireless Lan Device Item Description Network Type IEEE 802.11b Transfer Rate 11/5.5/2/1Mbps (auto change) Frequency Range 2,400 - 2,483 MHz Channels One of 13 channels is used Card Type Non-intelligent Class B Security Network name, encryption key Supported Operating Systems Windows 2000, Windows XP...

  • Page 72: About The Built-In Modem

    SECTION 1 9 About the built-in Modem CAUTION ELECTRIC SHOCK • To avoid shock hazards, do not put your finger into a phone jack (for modular cables) on the wall. CAUTION BREAKAGE • To avoid damage to your computer, do not plug a modular cable in any port other than the modem port.
  • Page 73 IMPORTANT If a rosette type phone jack is used, it needs be changed to a modular type. Changing a phone jack from rosette type to modular type must be done by an authorized technician or under his or her supervision. So, if you need to change the phone jack, you will have to ask your local Telephone system office or branch.

  • Page 74: Lifebook Security/Application Panel

    SECTION 1 10 LifeBook Security/Application Panel LifeBook Security / Application Panel (1) Application A Button (2) Application B Button (3) Internet Button (4) E-mail Button Enter Button Sus/Res Button A unique feature of your LifeBook is the Security/Application Panel that allows you to secure your LifeBook from unauthorized use.

  • Page 75: Passwords

    Passwords The user and supervisor password may be set on this LifeBook. A supervisor password is typically the same for all LifeBooks in a working group, office, or company to allow for system management. Individual LifeBooks in a group environment should not use a common password.

  • Page 76: Operating Your Lifebook Security/Application Panel

    Setting User Password 1. Go to the Start menu. 2. Click on Programs. 3. Click on Security Panel Application and Set User Password. 4. Follow the on-screen instructions to set the User password. Critical Points You may change or remove the supervisor or user password by repeating the steps defined above.

  • Page 77: Precautions

    Critical Points Remember the user password you specified on the Security Panel Application. If you forget the password you will not be able to use your computer. The supervisor password can override the user password. Precautions Opening and Closing the Cover Closing the cover automatically places the LifeBook into suspend mode.
  • Page 78 Novena Square Tower A Singapore 307684 Note: The authorised Fujitsu Service Center will not be able to reset the password. Please remember to keep your password in a safe place. There is a service charge for unlocking the password restricted LifeBook. You will bear all the cost returning the LifeBook to our service centre to unlock the password.

  • Page 79: Configuring Your Lifebook Application Panel

    Configuring your LifeBook Application Panel When you start Windows, the LifeBook Application Panel is automatically activated. As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature.
  • Page 80 The Application Panel Setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your notebook, these buttons are configured to launch specific applications. Below is the example of applications associated with each button.
  • Page 81 The button will now launch the new application. If you want to return to launching your Windows default Internet browser with this button, you need only click on “Default Internet Browser” from the Internet browser box. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application”...

  • Page 82: Configure Your E-Mail Account Settings

    Configure your E-mail Account Settings Critical Points The E-mail Notification LED is available on select LifeBook notebook models only. To use the E-mail LED notification, you must have access to a POP3 Server with no Security Password Authentication. Contact your service provider to determine if they support POP3 without Security Password Authentication.
  • Page 83 • If LAN: Click on LAN. Enter the POP3 Server name, your account name and password for that account. Consult your Service provider if you do not know or are unsure of the information requested. • If Dial Up: Click on Dial Up. Choose the Dial up configuration (as previously set in Dial Up Networking) you wish to retrieve mail from.
  • Page 84 To configure Auto Mail Check This function allow you to specify day and time for checking new mail. Only applicable when the PC stays Standby. To configure Mail Check Interval This function allow you to specify an interval (minutes) for checking for a new mail during you use the computer.
  • Page 85 To configure Special recipient This function allow you to add a special recipient on the Address List. You have to specify from the Mail Check Interval to check the check box of Periodically check for New Mail from the menu Mail Check Interval. There is an icon like envelop appear on the taskbar.
  • Page 86 To configure Important Mail (Only applicable for CoolView Panel model) This function allow you to change the icon color on the taskbar to notifies you that an important mail comes. To configure Sound This allow you to change the LifeBook Application icon’s color on the taskbar and beeps each time you receive a new message.

  • Page 87: Desktop Control Panel

    Desktop Control Panel Your LifeBook notebook includes a CD Player control panel. You may use this panel to operate the Disc Player. To use the desktop control panel: 1. Click on Start. 2. Click on All Programs. 3. Click on LifeBook Application Panel. 4.
  • Page 88 You can change the CD Player design by selecting the setting from the pull down menu from the CD Player options. Grey (High Color) Circle (High Color) Stick (High Color) Basic (16 colors) You can move the CD Player to anywhere on your desktop. Drag it by clicking on the track number display, holding it down, and dragging the control panel.
  • Page 89 SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION 2 2 2 2 2 2 2 2 2 2 This section explains installation of options for this computer.

  • Page 90: Options

    SECTION 2 1 Options Options You can expand the functions of this computer by connecting various options. FDD unit Numerical keypad USB mouse (USB) External display Printer Mouse PC card Combo drive unit (DVD/CD-R/RW) Memory Battery CD-R/RW drive unit PC Card Slot unit (Optional) 2nd Battery (Optional)

  • Page 91: Peripherals

    Peripherals Below explanation is necessary for your knowledge before connecting your peripherals. Some setting up works are required for a certain peripherals You cannot use some PC peripherals just by connecting it to a PC. Those peripherals require some setting up work after connection. For example, printers and PC cards require “driver installation”...

  • Page 92: Using A Pc Card

    SECTION 2 2 Using a PC Card Precautions for PC Cards Observe the following points when using PC cards to prevent breakdown. Do not place PC cards in high- Do not subject PC cards to Avoid rubbing PC cards and temperature locations and strong shocks.

  • Page 93: Cautions In Using A Pc Card

    Cautions in using a PC card CAUTION BREAKAGE • A PC card is composed of static-sensitive parts, and it is easily broken by static discharged from a human body. Before touching a PC card, always touch an appropriate metal object to discharge static from your body. To avoid damage, take the following precautions when using PC cards.

  • Page 94: Inserting A Pc Card

    Inserting a PC card CAUTION INJURY • When inserting a PC card into a PC card slot, be careful not to put your finger into the slot, otherwise you could injure your finger. Critical Points Before using a PC card, you might need to turn off your computer or to install the device driver, depending on the type of PC card used.

  • Page 95: Removing A Pc Card

    Removing a PC card Critical Points When removing a PC card with a cord, do not pull its cord to avoid damage to it. To remove a PC card when your computer is turned on, always follow the steps below. Failure to do so could damage your computer or PC card.
  • Page 96 When the Remove Hardware dialog box appears, press the PC card eject button. The PC card eject button springs out. PC card eject button (Your computer or situation may not look exactly like this illustration.) Remove the PC card. Press the PC card eject button again and pull out the PC card that came out a little. PC card PC card eject/lock button...

  • Page 97: Using The Cd/Dvd Drive

    SECTION 2 3 Using the CD/DVD drive In this manual, CD-ROMs, audio CDs and CD-R/RW discs are collectively referred to as CDs, and DVD-ROMs and DVD-Videos as DVDs. Also, CDs and DVDs are sometimes referred to simply as discs. CAUTION INJURY •...
  • Page 98 Supported discs CD-ROM, audio CD, DVD-ROM, CD-R CD-RW video CD, DVD-VIDEO photo CD Reading (playback)*1 Writing Rewriting *1: Some discs may be incompatible with your drive or may require a playback program. *2: DVD-ROMs refer to DVDs containing information intended for use with a computer, such as programs. DVD-Videos refer to DVDs containing audio and video files.

  • Page 99: Inserting A Disc

    1. Click the Start button and select Control Panel. 2. Click Performance and Maintenance, and then System. 3. Click the Hardware tab and select Device manager. 4. Click the plus sign [+] beside DVD/CD-ROM drive, and then double-click the CD/DVD drive that is displayed under it.
  • Page 100 Press the CD eject button. The tray springs out a little. CD eject button Pull out the tray gently. Tray Critical Points If the tray will not comes out – If Windows is shut down, turn your computer back on and press the CD eject button again. –...

  • Page 101: Removing A Disc

    Push the tray gently into the drive. It is about 10 seconds before the CD gets ready for use. Tray Critical Points If a message appears, asking what you want Windows to do each time you insert a disc or connect a device, click Do nothing, and then click OK.
  • Page 102 Tray Critical Points If the tray will not comes out – If Windows is shut down, turn your computer back on and press the CD eject button again. – If the computer is turned off, turn it on, and then press the CD eject button. You can press the eject button at any time, even when on the operating status indicator LED blinks.
  • Page 103 Critical Points If the disc cannot be ejected 1. Click the Start button and select My Computer. 2. In the My Computer window, right-click E drive in the Drives with Removable Storage area. 3. Click Eject. The tray springs out abit. 4.

  • Page 104: Adding Memory

    SECTION 2 4 Adding Memory Where to install memory Your computer has an expansion RAM module slot (slot 2) so that memory can be added. Your computer came with 256/512 MB of memory installed in slot 1. (depends the model you have) The memory capacity of your computer can be increased to a maximum of 1GB (512 MB of memory x 2).

  • Page 105: Installing Memory

    - Model with 512MB as standard memory. Total capacity Slot 1 Slot 2 512 MB (Installed as standard) 512 MB 640 MB 512 MB 128 MB 768 MB 512 MB 256 MB 1 GB (Maximum) 512 MB 512 MB Installing memory To install memory, perform these steps.
  • Page 106 CAUTION • Some components around the memory slot are very hot immediately after use. To avoid burns, do not install or remove memory immediately after turning off the computer but wait for a while until its internal components cool down. BREAKAGE •...
  • Page 107 Install memory. Insert the memory module into the slot with the notch in the memory module aligned with the projection on the connector, and turn it down until it clicks into place. Notch in the module Attach the expansion RAM module slot cover and secure it with the screws. Attach the cover removed in step 3.

  • Page 108: Changing Memory

    Check whether the circled numeric value in the figure below has increased by the size of the memory you have added. Memory capacity In this example, 256 MB of memory is added. * The memory capacity displayed is 8 MB less than the actual memory capacity, since your computer uses 8 MB of memory exclusively for graphics.
  • Page 109 Remove the memory. Remove the hook on each side from the memory module. The memory comes up slightly. Then, pull the memory diagonally up to detach it from the slot. Hook (Slot 2 (upper slot)) Hook (Slot 1 (lower slot)) Install a new memory module.

  • Page 110: Using A Mobile Multi-Purpose Bay Unit

    Never use a mobile multi-purpose bay unit if a foreign object, such liquid or metal chips, has gotten in it. If a foreign object has gotten into your multi-purpose bay unit, consult Fujitsu Customer Support Center or your retailer. •...
  • Page 111 IMPORTANT • Before changing the unit in the multi-purpose bay, be sure to exist all programs. Removing the unit from the mobile multi-purpose bay Steps you need to perform here vary depending on the situation and the kind of mobile unit you want to remove.
  • Page 112 If your computer is in Suspend mode, press the SUS/RES button to resume operation. Click the icon (Safely Remove Hardware) in the lower right corner of the screen (notification area where a clock is displayed). Select the device you want to unplug or eject and then click Stop. XXX refers to the name of the mobile multi-bay unit currently in use.
  • Page 113 After that, be sure to install a unit in the mobile multi-purpose bay. The use of your computer with the multi-purpose bay left empty could result in damage to your computer. Installing a unit in the mobile multi-purpose bay To install the new device into the Mobile bay for Win XP or W2K, you have to press the Sus/Res button and let the system in standby/hibernate.

  • Page 114: Connecting A Usb Device

    SECTION 2 6 Connecting a USB Device Preparing necessary items USB devices Devices that can be plugged in USB ports on your computer. Prepare USB device that meets your needs. • Digital camera • Mouse • Printer • Scanner • Keyboard Used to connect a USB device to your computer.

  • Page 115: Connecting A Usb Device

    Connecting a USB device Plug a USB cable in the connector of your USB device. Plug the cable from the USB device in a USB port on the back of your computer. Insert the connector with the face marked with USB port (Your computer or situation may not look exactly like this illustration.) Install the driver.

  • Page 116: Connecting A Mouse

    SECTION 2 7 Connecting a Mouse Connecting a USB mouse Plug a mouse in the USB port on the back of your computer. Insert the plug with the face marked with USB port (Your computer or situation may not look exactly like this illustration.) Critical Points A USB mouse can be connected to and disconnected from your computer at any time without shutting down the computer.
  • Page 117 Critical Points Even though Flat Point is disabled by pressing the [ ] and [ ] keys at the same time, it will be enabled automatically when your computer is restarted or when it resumes operation. If you want to disable Flat Point again, press the [ ] key again while holding down the Fn key.

  • Page 118: Connecting An External Monitor

    SECTION 2 8 Connecting an External Monitor Preparing necessary items External monitor Your computer supports PC/AT-compatible and DOS/V-compatible monitors. Monitor cable Used to connect an external monitor to your computer. Most external monitors come with this cable, as a separate part for some monitors and already connected for others.
  • Page 119 The external monitor port has a trapezoidal cross-section. (1) Insert the connector straight into the external monitor port with the right side up, and (2) secure it with the screws on both sides of the connector. External monitor port Monitor cable Connect the other end of the cable to the CRT monitor.
  • Page 120 SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION SECTION 3 3 3 3 3 3 3 3 3 3 This section explains what to do when trouble occurs with this computer and when messages are displayed. Read this section as the necessity arises.

  • Page 121: When This Happens

    SECTION 3 1 When This Happens When you are having trouble with this computer, there is something you think is strange, or there is something you want to do, but do not know how. This section is divided into related items.
  • Page 122 Checkpoint Cause and Solution Have you been pressing any On this computer, if the power management functions are set of the keys? and no key is pressed for a certain period of time, the CPU stops and the LCD panel backlight goes out. (In this state, pressing any key lights up the backlight again.) If the computer stops too frequently, change the BIOS setup settings.
  • Page 123 The remaining battery charge indicator does not stop flashing. Checkpoint Cause and Solution Is the battery connected Check that the battery is connected correctly. If it is connected correctly? correctly, there is an abnormality in the battery pack, so replace the battery pack.
  • Page 124 No sound or minimal sound from speaker Checkpoint Cause and Solution Is the volume control Turn the volume control for the correct volume. If this does not correctly adjusted? change the volume, double click the task bar sound indicator and adjust the volume. Check also whether the sound driver is installed correctly.
  • Page 125 Data cannot be read from the CD-ROM drive. Checkpoint Cause and Solution Is the CD-ROM correctly set? Set the CD-ROM correctly with its label facing upwards. Is there any dirt, Wipe it from the center outwards with a dry, soft cloth. condensation or water on the CD-ROM? Is the CD-ROM scratched or...

  • Page 126: Care And Maintenance

    SECTION 3 2 Care and Maintenance If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. Caution: Electrical equipment may be hazardous if misused. Operations of this product or similar products, must always be supervised by an adult.
  • Page 127 Storing your LifeBook Notebook • If storing your notebook for a month or longer, turn your LifeBook notebook off and remove all Lithium Ion batteries. • Store your LifeBook notebook and batteries separately. If you store your notebook with a battery installed, the battery will discharge, and battery life will be reduced.

  • Page 128: Floppy Disks And Drives

    • When travelling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel.
  • Page 129 Caring for your Floppy Disk Drive • To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.
  • Page 130 Caring for your DVD/CD-RW/CD-ROM Drive Your DVD/CD-RW/CD-ROM drive is durable but you must treat it with care. Please pay attention to the following points: • The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.

  • Page 131: Glossary

    SECTION 3 3 Glossary Glossary of Terms Used in This Document AdHoc A name of a wireless LAN configuration. It is a type of communication using wireless cards only. Another type of communication is called Infrastructure (using a wireless card and an access point). ADSL Asymmetric Digital Subscriber Line Technology for transporting high bit-rate services over ordinary phone lines.
  • Page 132 Channel A radio frequency band used for communication between wireless cards and access points. Cache Memory A block of memory built into the micro-processor which ins much faster to access than your system RAM and used in specially structured ways to make your overall data handling tine faster. CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.
  • Page 133 Direct Memory Access. Special circuitry for memory to memory transfer of data which do not require CPU action. Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems hardware and software components, and peripherals.
  • Page 134 Electro-Static Discharge. The sudden discharge of electricity form a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get form brushing hair on a dry day. Extended Memory All memory more than the 640KB recognized by MS-DOS as system memory.
  • Page 135 Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. An abbreviation for infrared. IrDA Infrared Data Association.
  • Page 136 MAC Address Media Access Control Address A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards.
  • Page 137 PPPoE Point to Point Protocol over Ethernet A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line. Protocol Procedures and rules use to send and receive data between computers. - Method of sending and receiving data - Process used to handle communication errors Conditions required for communication are organized in procedures for correct transfer of information.
  • Page 138 PS/2 An IBM series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors. Random Access Memory. A hardware component of your notebook that holds binary information (both program and data) as long as it has the proper power applied to it. RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.
  • Page 139 SMART Self-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides near-term failure predictions for hard drives. When SMART is enabled the hard drive monitors predetermined drive attributes that are susceptible to degradation over time. If a failure is likely to occur.
  • Page 140 Video Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers. VRAM Video Random Access Memory. A memory dedicated to video display data and control. Wi-Fi Compatible Wi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guarantees the interoperability of wireless IEEE 802.11 LAN products.

Table of Contents