Specifications - Hitachi C 10FCB Handling Instructions Manual

PRECAUTION FOR COMPOUND SAW
1. Never use the compound saw with its safety cover
locked in the open position.
2. Ensure that the safety cover moves smoothly.
3. Do not use the saw without guards in position.
4. Always keep the saw blade sharp.
5. Do not use saw blades which are damaged or
deformed.
6. Use only saw blades recommended by HITACHI.
7. Select saw blades in relation to the material to be
cut.
8. Never operate the compound saw with the saw
blade turned upward or to the side.
9. Ensure that the workpiece is free of foreign matter
such as nails.

SPECIFICATIONS

Max. Cutting
Capacity
Height × Width
Saw Blade Diameter
Miter Cutting Angle
Bevel Cutting Angle
Voltage (by areas)*
Power Input*
No-Load Speed
Weight (Net)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) 255 mm TCT Saw blade ............................................ 1
(2) Dust bag ..................................................................... 1
(3) 10 mm Box wrench ................................................... 1
(4) Vise Assembly ........................................................... 1
(5) Collar (A) (D30) .......................................................... 1
(6) Collar (B) (D25.4) (mount on tool) ............................ 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Extension Holder and Stopper
(2) Saw blade 255 mm TCT Saw blade for fine surface
(Total teeth: 60)
(3) Saw blade 255 mm TCT Saw blade for normal cut
(Total teeth: 70)
Optional accessories are subject to change without notice.
APPLICATION
Cutting various types of aluminium sash and wood.
0°
Miter 45°
Bevel 45°
Miter + Bevel 45°
10. Replace table insert when worn.
11. Do not use the saw to cut other than aluminium,
wood or similar materials.
12. Connect compound saw to a dust collecting device
when sawing.
13. Take care when slotting.
14. When transporting or carrying the tool, do not grasp
the holder. Grasp the handle instead of the holder.
15. Start cutting only after motor revolution reaches
maximum speed.
16. Promptly cut OFF the switch when abnormality
observed.
17. Shut off power and wait for saw blade to stop
before servicing or adjusting tool.
18. During a miter or bevel cut the blade should not be
lifted until it has stopped rotation completely.
59 mm × 144 mm (89 mm × 101 mm)
59 mm × 102 mm (89 mm × 70 mm)
41 mm × 144 mm
41 mm × 102 mm (44 mm × 89 mm)
Right 0° – 60°, Left 0° – 45°
Left 0° – 45°
(110V, 220V, 230V, 240V)
4900/min
UNPACKING
Carefully unpack the power tool and all related items
(standard accessories).
Check carefully to make certain all related items
(standard accessories) are present.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. When the power tool is prepared for shipping, its
main parts are secured by a locking pin.
Move the handle slightly so that the locking pin can
be disengaged.
During transport, lock the locking pin into the gear
case (Fig. 1).
255 mm
1640 W
14 kg
3