Table of Contents

Advertisement

QQ
3 7 63 1515 0

SERVICE MANUAL

Ver. 1.1 2005.11
HCD-FX10 is the amplifier, DVD/CD and
tuner section in DAV-FX10.
This system incorporates with Dolby*1 Digital and
Dolby Pro Logic (II) adaptive matrix surround decoder
and the DTS*2 Digital Surround System.
*1 Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D symbol are trademarks
of Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
TE
L 13942296513
"DTS" and "DTS Digital Surround" are trademarks of Digital
Theater Systems, Inc.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION:
Amplifier section
Surround mode (reference) music power output
* Depending on the sound field settings and the source ,
there may be no sound output.
www
.
Sony Corporation
9-879-623-02
Home Audio Division
2005K16-1
Published by Sony Engineering Corporation
© 2005.11
http://www.xiaoyu163.com
Inputs (Analog)
VIDEO 1, VIDEO 2
Inputs (Digital)
With 3 ohm loads, both
VIDEO 1 (Coaxial)
channels driven, from
VIDEO 2 (Optical)
200 – 20,000 Hz; rated
Phones
55 watts per channel
minimum RMS power,
with no more than 0.7 %
Super Audio CD/DVD system
total harmonic distortion
from 250 milli watts to
Laser
rated output.
Front: 143 W + 143 W
Signal format system
(with SS-TS43)
Frequency response (at 2 CH STEREO mode)
Center*: 143 W
(with SS-CT43)
Surround*: 143 W + 143
W
(with SS-TS43B)
Subwoofer*: 285 W
Tuner section
(with SS-WS42)
System
FM tuner section
Tuning range
Antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
x
ao
u163
y
Intermediate frequency
i
http://www.xiaoyu163.com
HCD-FX10
2 9
8
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
Q Q
3
6 7
1 3
1 5
SPECIFICATIONS
Sensitivity: 450 mV
Impedance: 50 kilohms
Impedance: 75 ohms
Accepts low-and high-
impedance headphones.
Semiconductor laser
(Super Audio CD/DVD: λ
= 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
NTSC
DVD (PCM): 2 Hz to 22
kHz (±1.0 dB)
CD: 2 Hz to 20 kHz (±1.0
dB)
PLL quartz-locked digital
synthesizer system
87.5 – 108.0 MHz
(100 kHz step)
FM wire antenna (aerial)
co
10.7 MHz
.
9 4
2 8
US Model
Canadian Model
NEW
CDM69EH-DVBU101
KHM-310CAB/C2NP
0 5
8
2 9
9 4
2 8
AM tuner section
Tuning range
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section
Outputs
Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
/C
, P
B
B
R
75 ohms
Input
VIDEO1, VIDEO2: 1 Vp-p
75 ohms
— Continued on next page —
m
DVD RECEIVER
9 9
9 9
/C
: 0.7 Vp-p
R

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-FX10

  • Page 1: Service Manual

    3 7 63 1515 0 SERVICE MANUAL US Model Canadian Model Ver. 1.1 2005.11 HCD-FX10 is the amplifier, DVD/CD and tuner section in DAV-FX10. This system incorporates with Dolby*1 Digital and Model Name Using Similar Mechanism Dolby Pro Logic (II) adaptive matrix surround decoder...
  • Page 2 LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 HCD-FX10 3 7 63 1515 0 Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the bottom exterior.
  • Page 4: Table Of Contents

    HCD-FX10 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTE 6-4. Printed Wiring Board – DMB10 Section (Side A) – ..35 ........... 5 6-5. Printed Wiring Board – DMB10 Section (Side B) – ..36 6-6. Schematic Diagram – DMB10 Section (1/4) – ....37 GENERAL ..............
  • Page 5: Servicing Note

    To prevent a malfunction, the system has performed the self- (xx is a number) diagnosis function. u163 ,Contact your nearest Sony dealer or local authorized Sony service facility and give the 5- character service number. Example: E 61 10 http://www.xiaoyu163.com...
  • Page 6: General

    HCD-FX10 SECTION 2 This section is extracted from instruction manual. 3 7 63 1515 0 GENERAL Index to Parts and Controls For more information, refer to the pages indicated in parentheses. Front panel A Disc slot (31) H x (stop) (32, 71)
  • Page 7 HCD-FX10 3 7 63 1515 0 D ./> PRESET –/+, TV CH –/+ (28, Remote 32, 68) E H (play) (31) button has a tactile dot.* F TOP MENU (36) G C/X/x/c/ENTER (27, 33, 45, 55, 58, 60, 67, 72) C/X/x/c have tactile dots.*...
  • Page 8: Disassembly

    HCD-FX10 SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
  • Page 9: Top Panel Sub Assy

    HCD-FX10 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. TOP PANEL SUB ASSY top panel sub assy 2 two flat head screws (TP) 1 two flat head screws (TP) 4 three screws 3 ×...
  • Page 10: Front Panel Assy

    HCD-FX10 3 7 63 1515 0 3-3. FRONT PANEL ASSY 2 three screws 3 × 8) (+BVTP MD cover screw 3 × 8) (+BVTP 4 wire (flat type) 19p(CN801) front panel assy L 13942296513 5 four screws 3 × 8) (+BVTP 3-4.
  • Page 11: Dmb10 Board

    HCD-FX10 3 7 63 1515 0 3-5. DMB10 BOARD 4 wire (flat type) 11p(CN4501) 7 two screws 5 connector (CN401) (+BV 8 two screws 3 wire (flat type) (+BV 13p(CN4802) DMB10 board 2 wire (flat type) 24p(CN101) 6 wire (flat type)
  • Page 12: Main Board, H/P Board

    HCD-FX10 3 7 63 1515 0 3-6. MAIN BOARD, H/P BOARD 9 two screws 7 wire (flat type) (+BV 23p(CN507) screw 8 wire (flat type) 3 × 14) (+BVTP 11p(CN504) 6 wire (flat type) 27p(CN502) heat sink 5 wire (flat type)
  • Page 13: Dvd Mechanism Deck (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 3-8. DVD MECHANISM DECK (CDM69EH-DVBU101) 3 DVD mechanism deck (CDM69EH-DVBU101) 1 two screws 2 two screws (+BV (+BV L 13942296513 3-9. BASE UNIT (DVBU101) 1 floating screw (DIA. 12) 2 boss 5 boss...
  • Page 14: Optical Pick-Up (Khm-310Cab/C2Np)

    HCD-FX10 3 7 63 1515 0 3-10. OPTICAL PICK-UP (KHM-310CAB/C2NP) 3 insulator screw optical pick-up (KHM-310CAB/C2NP) 8 insulator 2 insulator screw 4 insulator screw 7 insulator 9 insulator 1 insulator screw 6 insulator L 13942296513 3-11. SW BOARD, BRACKET (TOP) ASSY...
  • Page 15: Relay Board

    HCD-FX10 3 7 63 1515 0 3-12. RELAY BOARD 4 connector (CN710) – bottom view – 5 connector (CN703) RELAY board 2 four screws (+BVTP2.6) 6 RELAY board 1 Remove five solders. L 13942296513 3-13. MOTOR (STOCKER) ASSY (STOCKER)(M761) 3 two screws (+BVTP2.6)
  • Page 16: Motor (Roller) Assy (Roller)(M781)

    HCD-FX10 3 7 63 1515 0 3-14. MOTOR (ROLLER) ASSY (ROLLER)(M781) 3 two screws (+BVTP2.6) 2 Remove two solders. 4 ROLLER MOTOR board 5 motor (roller) assy (roller)(M781) 1 belt (roller V) L 13942296513 3-15. MOTOR (MODE) ASSY (MODE)(M771) 3 two screws (+BVTP2.6)
  • Page 17: Rubber Roller (Slider) Assy

    HCD-FX10 3 7 63 1515 0 3-16. RUBBER ROLLER (SLIDER) ASSY 5 step screw 8 step screw 1 step screw 9 tension 7 rubber roller spring 0 rubber roller (slider 1) assy (slider 2) (slider 4) assy 2 rubber roller...
  • Page 18: Cam (Gear)

    HCD-FX10 3 7 63 1515 0 3-18. CAM (GEAR) qf cam (gear) : Note 6 gear (mode 5) qd screw 5 screw (PTPWH2.6 × 8) 4 gear (mode 5) qs gear(mode cam) 3 screw (PTPWH2.6 × 8) qa screw (PTPWH2.6 ×...
  • Page 19: Assembly

    HCD-FX10 SECTION 4 3 7 63 1515 0 ASSEMBLY • This set can be assembled in the order shown below. 4-1. HOW TO INSTALL THE CAM (EJECT LOCK) 1 Rotate the cam (BU U/D) fully in the direction of arrow.
  • Page 20: How To Install The Gear (Mode C)

    HCD-FX10 3 7 63 1515 0 4-3. HOW TO INSTALL THE GEAR (MODE C) 1 Align the mark on the rotary encoder (S771) with the projection of the assy. 2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
  • Page 21: How To Install The Rotary Encorder (S702)

    HCD-FX10 3 7 63 1515 0 4-5. HOW TO INSTALL THE ROTARY ENCORDER (S702), GEAR (STOCKER COMMUNICATION) 4 gear 5 screw (PTPWH2.6 × 8) (stocker communication) 3 screw 7 two screws (PWH2 × 6) (PTPWH2.6 × 8) 1 rotary encoder...
  • Page 22: Test Mode

    HCD-FX10 SECTION 5 3 7 63 1515 0 TEST MODE 3. Disc Tray Lock Note 1: Regarding the notification symbol “R” The disc tray lock function for the antitheft of an demonstration Because the number of the operating buttons of this product disc in the store is equipped.
  • Page 23 HCD-FX10 Ver. 1.1 3 7 63 1515 0 4-4. MIRROR TIME ADJUSTMENT DVD SECTION [TEST DISC LIST] To enter Mirror Time Adjustment, press 5 “R” button on the remote Be sure to use the DVD disc that matches the signal standards of commander.
  • Page 24 HCD-FX10 3 7 63 1515 0 (3) Select “5. MIRR time Adjust”. (14) Confirm the same values are displayed. If it is not same, return to step 7. Drive Manual Operation MIRR time Adjust Menu 1. Servo Control 2. Track/Layer Jump 1.
  • Page 25 HCD-FX10 3 7 63 1515 0 4-5. EXECUTING IOP MEASUREMENT (5) Wait until a hexadecimal number appear. Manual Adjust In order to execute mirror time adjustment, the following standard procedures must be followed. 1. Track Balance Adjust: 2. Track Gain Adjust: (1) In standby mode, press three buttons x , A and VOLUME 3.
  • Page 26: Diagrams

    HCD-FX10 SECTION 6 3 7 63 1515 0 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams. For Printed Wiring Boards.
  • Page 27 HCD-FX10 3 7 6 3 1 5 1 5 0 MEMO • Circuit Boards Location I/O board MAIN board DMB10 board KEY board LED board H/P board FL board 1 3 9 4 2 2 9 6 5 1 3...
  • Page 28: Block Diagram - Rf Section

    HCD-FX10 6-1. BLOCK DIAGRAM – RF SECTION – 3 7 6 3 1 5 1 5 0 DVDRFIP DVDA DVDB DETECTOR DVDC DVDD 8 NA 9 NB IC102 (1/3) CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP DVD SYSTEM PROCESSOR OPTICAL PICK-UP...
  • Page 29: Video Section

    HCD-FX10 – VIDEO SECTION – 3 7 6 3 1 5 1 5 0 J601(1/2) VIDEO1 VIDEO IN VIDEO2 VIDEO IN IC201 IC204 VIDEO AMP, 75Ω DRIVER VIDEO SWITCH 14 2B OUT2 6 YIN YOUT YUV1 S VIDEO(DVD ONLY)
  • Page 30: Amp Section

    HCD-FX10 – AMP SECTION – 3 7 6 3 1 5 1 5 0 IC4501 BUFFER LRCK0 BCK0 IC506 IC507 DIGITAL AUDIO ALRCK SD-RAM PROCESSOR ABCK ACLK 7-10 72-75 13-16 77-80 18-21 ASDATA0 D0-D15 D0 – D15 98,99 IC4502...
  • Page 31: Audio Section

    HCD-FX10 – AUDIO SECTION – 3 7 6 3 1 5 1 5 0 IC301 IC108 HEADPHONE STREAM PROCESSOR J801 HPOUTL1 PHONES HPOUTL2 • Signal Path Q507 HPOUTR1 Q806 - 809 : AUDIO MUTING MUTING HPOUTR2 CONTROL IC101 POWER DRIVER SPEAKER D1 –...
  • Page 32: Power Section

    HCD-FX10 – POWER SECTION – 3 7 6 3 1 5 1 5 0 IC721 STOCKER MOTOR DRIVE OUT1 M761 (STOCKER) OUT2 IC711 ROLLER MOTOR DRIVE OUT1 M781 (ROLLER) OUT2 IC701 MODE MOTOR DRIVE OUT1 DC/DC M771 OUT2 (MODE)
  • Page 33: Printed Wiring Board - Changer Section

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-2. PRINTED WIRING BOARD – CHANGER SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SW(1) BOARD RELAY BOARD MAIN BOARD CN502 (Page 41) SW(2) BOARD...
  • Page 34: Schematic Diagram - Changer Section

    HCD-FX10 • See page 58 for IC Block Diagrams. 6-3. SCHEMATIC DIAGRAM – CHANGER SECTION – 3 7 6 3 1 5 1 5 0 RELAY BOARD CN751 CN702 R731 DIODE DIODE I C 7 5 1 D SENSE...
  • Page 35: Printed Wiring Board - Dmb10 Section (Side A)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-4. PRINTED WIRING BOARD – DMB10 SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually.
  • Page 36: Printed Wiring Board - Dmb10 Section (Side B)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-5. PRINTED WIRING BOARD – DMB10 SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC105 IC107...
  • Page 37: Schematic Diagram - Dmb10 Section (1/4)

    HCD-FX10 6-6. SCHEMATIC DIAGRAM – DMB10 SECTION (1/4) – 3 7 6 3 1 5 1 5 0 FL401 CN401 FB402 FB404 JL4601 JL4602 FL403 JL4603 JL4604 FB403 FB406 JL4605 JL4606 (Page 38, JL4607 JL4608 C402 C403 JL4609 JL4610 MAIN 6.3V...
  • Page 38: Schematic Diagram - Dmb10 Section (2/4)

    HCD-FX10 • See page 67 for IC Pin Function Description. • See page 58 for Waveforms. 6-7. SCHEMATIC DIAGRAM – DMB10 SECTION (2/4) – 3 7 6 3 1 5 1 5 0 (Page 37) (Page 39) (Page 37)
  • Page 39: Schematic Diagram - Dmb10 Section (3/4)

    HCD-FX10 6-8. SCHEMATIC DIAGRAM – DMB10 SECTION (3/4) – 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually. Replace it with DMB10 board assembly for service. (Page 38) (Page 38) C181...
  • Page 40: Schematic Diagram - Dmb10 Section (4/4)

    HCD-FX10 6-9. SCHEMATIC DIAGRAM – DMB10 SECTION (4/4) – 3 7 6 3 1 5 1 5 0 (Page 38) (Page 37, R225 R223 100k 100k R232 R234 R231 R221 C211 0.033 C209 R230 C233 0.033 0.0047 C212 R233 C215 0.01...
  • Page 41: Printed Wiring Board - Main Section (Side A)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-10. PRINTED WIRING BOARD – MAIN SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D503 D914...
  • Page 42: Printed Wiring Board - Main Section (Side B)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-11. PRINTED WIRING BOARD – MAIN SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SPEAKER FRONT:ONLY FOR SS-TS43 SURROUND:ONLY FOR SS-TS43B • Semiconductor...
  • Page 43: Schematic Diagram - Main Section (1/8)

    HCD-FX10 • See page 64 for IC Pin Function Description. • See page 58 for Waveform. 6-12. SCHEMATIC DIAGRAM – MAIN SECTION (1/8) – 3 7 6 3 1 5 1 5 0 CN509 FFC-S-1.0 ( 1 / 8 )
  • Page 44: Schematic Diagram - Main Section (2/8)

    HCD-FX10 6-13. SCHEMATIC DIAGRAM – MAIN SECTION (2/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (1/8) (Page 43) IC515 ( 2 / 8 ) IC TA7809LS TP517 C595 C596 C597 R704 47 35V 0.33...
  • Page 45: Schematic Diagram - Main Section (3/8)

    HCD-FX10 • See page 59 for IC Block Diagrams. 6-14. SCHEMATIC DIAGRAM – MAIN SECTION (3/8) – 3 7 6 3 1 5 1 5 0 ( 3 / 8 ) R345 R347 TP331 R317 R316 EB907 TERMINAL BOARD...
  • Page 46: Schematic Diagram - Main Section (4/8)

    HCD-FX10 • See page 59 for IC Block Diagrams. 6-15. SCHEMATIC DIAGRAM – MAIN SECTION (4/8) – 3 7 6 3 1 5 1 5 0 ( 4 / 8 ) R384 R480 R383 C137 IC106 R120 R128 25V F...
  • Page 47: Schematic Diagram - Main Section (5/8)

    HCD-FX10 • See page 59 for IC Block Diagram. • See page 58 for Waveform. 6-16. SCHEMATIC DIAGRAM – MAIN SECTION (5/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (3/8) (Page 45) ( 5 / 8 )
  • Page 48: Schematic Diagram - Main Section (6/8)

    HCD-FX10 • See page 59 for IC Block Diagrams. 6-17. SCHEMATIC DIAGRAM – MAIN SECTION (6/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (4/8) (Page 46) ( 6 / 8 ) IC103 Q106 Q108...
  • Page 49: Schematic Diagram - Main Section (7/8)

    HCD-FX10 6-18. SCHEMATIC DIAGRAM – MAIN SECTION (7/8) – 3 7 6 3 1 5 1 5 0 ( 7 / 8 ) MAIN BOARD (6/8) C938 D931 330P YG906C2R (Page 48) CN901 FH901 FH902 C963 HOLDER HOLDER 680P...
  • Page 50: Schematic Diagram - Main Section (8/8)

    HCD-FX10 • See page 58, 60 for IC Block Diagrams. • See page 58 for Waveform. 6-19. SCHEMATIC DIAGRAM – MAIN SECTION (8/8) – 3 7 6 3 1 5 1 5 0 R543 R528 R527 R538 L503 C541...
  • Page 51: Printed Wiring Board - Fl/Key Section

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-20. PRINTED WIRING BOARD – FL/KEY SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D801 D802 D803 D804...
  • Page 52: Schematic Diagram - Fl/Key Section

    HCD-FX10 • See page 58 for IC Block Diagrams. 6-21. SCHEMATIC DIAGRAM – FL/KEY SECTION – 3 7 6 3 1 5 1 5 0 R852 R855 R857 R858 R851 R853 R856 2.2k 2.2k 4.7k 2.2k 4.7k 2.2k TP833...
  • Page 53: Printed Wiring Board - Led / H/P Section

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-22. PRINTED WIRING BOARD – LED / H/P SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D811 PHONES...
  • Page 54: Schematic Diagram - Led / H/P Section

    HCD-FX10 6-23. SCHEMATIC DIAGRAM – LED / H/P SECTION – 3 7 6 3 1 5 1 5 0 R833 R867 TP843 4.7k R834 R835 R836 R837 R838 R839 R863 R866 TP841 2.2k 2.2k 4.7k L813 CN803 S815 S809...
  • Page 55: Printed Wiring Board - I/O Section (Side A)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-24. PRINTED WIRING BOARD – I/O SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC201 IC203...
  • Page 56: Printed Wiring Board - I/O Section (Side B)

    HCD-FX10 • See page 27 for Circuit Boards Location. 6-25. PRINTED WIRING BOARD – I/O SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 AUDIO IN MONITOR VIDEO 1 VIDEO IN COMPONENT...
  • Page 57: Schematic Diagram - I/O Section

    HCD-FX10 • See page 61 for IC Block Diagrams. • See page 58 for Waveform. 6-26. SCHEMATIC DIAGRAM – I/O SECTION – 3 7 6 3 1 5 1 5 0 CN101 R659 TP626 TP625 TP627 L601 IC603 TORX141L...
  • Page 58 HCD-FX10 • IC Block Diagrams • Waveforms 3 7 6 3 1 5 1 5 0 – DMB10 Board – IC102 6 (DVDRFIP) IC102 <xx. (XTALI) IC102 <z.v (YUV1) – RELAY Board – – FL Board – 1.3 Vp-p...
  • Page 59 HCD-FX10 3 7 63 1515 0 IC101-107 CXD9775M GVDD B GVDD GVDD B BST B DVDD DREG DREG GND 1 PVDD B GATE PWM BP 2 PVDD B RECEIVER DRIVE OUT B TIMING GND 3 OUT B CONTROL DGND &...
  • Page 60 HCD-FX10 3 7 63 1515 0 IC505 LC89056W-E AUDIO C BIT PA/PB DETECT DETECT EMPHA SAMPLING FREQUENCY MICROCOMPUTER INTERFACE XSEL XOUT LOCK CLOCK DETECT XMCK 19 DVDD MODE0 MODE 18 DGND SELECT MODE1 XSTATE DGND DATAO DVDD LRCK DOSEL0...
  • Page 61 HCD-FX10 3 7 63 1515 0 – I/O Board – IC203 NJM2235V (TE2) IC601 MC14052BDR2 IN 1 BUFFER SW 1 IN 2 BIAS SW 2 VIN 3 IC201 MM1623BFBE S-DC OUT VCC1 VCC2 S1/S2 L 13942296513 150kΩ BIAS 200Ω...
  • Page 62 HCD-FX10 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC506 CXD9862R (DIGITAL AUDIO PROCESSOR) Pin No. Pin Name Description — Ground terminal XRST System reset signal input from the system controller “L”: reset EXTIN Master clock signal input terminal (not used)
  • Page 63 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description WMD0 External memory wait mode setting terminal (fixed at “H” in this set) PAGE2 External memory page selection signal output terminal (not used) — Ground terminal 52, 53...
  • Page 64 HCD-FX10 3 7 63 1515 0 MAIN BOARD IC509 M30622MGP-A14FPUO (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP SCDT/ Digital amp (IC108 to 110) data output DIAT SDATA DAMP SHIFT/ Digital amp (IC108 to 110) data output DIAT SCLK...
  • Page 65 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description DRIVE_RST(EN) Driver signal reset DRIVE_OCP(DIAG) Digital amp (power driver) diag OVERFLOW1 Over flow status1 of digital amp (IC110) OVERFLOW2 Over flow status2 of digital amp (IC108 to 110)
  • Page 66 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description — Ground KEY0 Key input 0 VREF Reference Voltage (+3.3V) Power supply (+3.3V) M-ST/WMUTE WMUTE signal output (not used) L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 67 HCD-FX10 3 7 63 1515 0 DMB10 BOARD IC102 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Terminal Ground DVDA AC coupled input path A DVDB AC coupled input path B...
  • Page 68 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description Not Used Not Used Not Used MAMUTE MAMUTE signal output to System Controller (IC509) DVDD18 — Power Supply (+1.8V) 53 to 58 IOA 2 to 7 Address bus 2 to 7 output to PROM (IC101)
  • Page 69 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description DQMO DQM0 signal output to SD-RAM (IC104) DQS0 DQM signal input Data bus 7 from SD-RAM (IC104) DVSS — Terminal Ground 117, 118 RD 6, 5 Data bus 6, 5 from SD-RAM (IC104) DVSS —...
  • Page 70 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description LIMSW LIMSW signal output to Optical pick-up OCSW SEN signal input from System Controller (IC509) VCLK — Not Used CKSW — Not Used — Not Used TSDM TSDM signal output to Motor driver (IC201) DVDD3 —...
  • Page 71 HCD-FX10 3 7 63 1515 0 Pin No. Pin Name Description SDPIF — SPDIF output (not used) RFGND18 — Terminal Ground RFVDD18 — Power Supply (+1.8V) ZTALO Oscillator output signal ZTALI Oscillator input signal JITFO RF jitter meter output...
  • Page 72: Exploded Views

    HCD-FX10 SECTION 7 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 73: Q Q 7-2. Front Panel Assy Section

    HCD-FX10 3 7 63 1515 0 7-2. FRONT PANEL ASSY SECTION supplied supplied supplied L 13942296513 not supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-585-417-01 WINDOW (FL) 1-828-336-11 WIRE (FLAT TYPE) (15 CORE)
  • Page 74: Chassis Section-1

    HCD-FX10 3 7 63 1515 0 7-3. CHASSIS SECTION-1 not supplied not supplied not supplied not supplied chassis section-2 not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1074-640-A TUNER UNIT (DTP-005 UC)
  • Page 75: Chassis Section-2

    HCD-FX10 Ver. 1.1 3 7 63 1515 0 7-4. CHASSIS SECTION-2 DVD mechanism deck section not supplied F902 not supplied not supplied not supplied not supplied not supplied L 13942296513 not supplied Ref. No. Part No. Description Remark Ref. No.
  • Page 76: Dvd Mechanism Deck Section-1 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-5. DVD MECHANISM DECK SECTION-1 (CDM69EH-DVBU101) S702 M761 L 13942296513 DVD mechanism deck section-2 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-725-13 STOCKER MOTOR BOARD 4-239-699-01 PULLEY 3-087-053-01 +BVTP2.6 (3CR)
  • Page 77: Dvd Mechanism Deck Section-2 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-6. DVD MECHANISM DECK SECTION-2 (CDM69EH-DVBU101) DVD mechanism deck section-3 DVD mechanism deck section-4 L 13942296513 optical pick-up section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-727-13 SW (1) BOARD 3-087-053-01 +BVTP2.6 (3CR)
  • Page 78: Dvd Mechanism Deck Section-3 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-7. DVD MECHANISM DECK SECTION-3 (CDM69EH-DVBU101) not supplied supplied not supplied supplied supplied L 13942296513 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-040-01 SPRING (DISC STOPPER), TORSION 4-240-039-01 LEVER (DISC STOPPER) 4-992-069-01 SCREW (+PTPWH) (M2) (DIA.
  • Page 79: Dvd Mechanism Deck Section-4 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-8. DVD MECHANISM DECK SECTION-4 (CDM69EH-DVBU101) supplied L 13942296513 M781 DVD mechanism deck section-5 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4954-626-1 LEVER (ROLLER) ASSY 4-240-041-01 SPRING (SLIDER 2), TENSION 4-239-666-01 GEAR 3-087-053-01 +BVTP2.6 (3CR)
  • Page 80: Dvd Mechanism Deck Section-5 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-9. DVD MECHANISM DECK SECTION-5 (CDM69EH-DVBU101) L 13942296513 DVD mechanism deck section-6 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-020-01 GEAR (TIMING) 4-239-699-01 PULLEY 4-239-708-02 BELT (FRONT), TIMING...
  • Page 81: Dvd Mechanism Deck Section-6 (Cdm69Eh-Dvbu101)

    HCD-FX10 3 7 63 1515 0 7-10. DVD MECHANISM DECK SECTION-6 (CDM69EH-DVBU101) M771 not supplied L 13942296513 supplied S771 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-239-693-02 CAM (GEAR) 4-241-731-01 SHUTTER (A), LEVER 1-686-723-13 SENSOR BOARD...
  • Page 82: Optical Pick-Up Section (Khm-310Cab/C2Np)

    HCD-FX10 3 7 63 1515 0 7-11. OPTICAL PICK-UP SECTION (KHM-310CAB/C2NP) L 13942296513 not supplied Ref. No. Part No. Description Remark 0 601 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP) 3-087-599-01 INSULATOR SCREW 3-088-372-01 INSULATOR u163 http://www.xiaoyu163.com...
  • Page 83: Electrical Parts List

    HCD-FX10 Ver. 1.1 SECTION 8 DMB10 3 7 63 1515 0 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms.
  • Page 84 HCD-FX10 DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C206 1-164-230-11 CERAMIC CHIP 220PF FL401 1-234-494-21 FILTER, EMI REMOVAL (SMD) C208 1-162-970-11 CERAMIC CHIP 0.01uF FL402 1-233-893-21 FILTER, CHIP EMI...
  • Page 85 HCD-FX10 DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R155 1-216-805-11 METAL CHIP 1/10W R1150 1-216-827-11 METAL CHIP 3.3K 1/10W R160 1-216-805-11 METAL CHIP 1/10W R1151 1-216-827-11 METAL CHIP 3.3K...
  • Page 86 HCD-FX10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1104-753-A FL BOARD, COMPLETE < FERRITE BEAD > ****************** FB801 1-414-813-11 FERRITE, EMI (SMD) (2012) < CAPACITOR > FB802 1-414-813-11 FERRITE, EMI (SMD) (2012)
  • Page 87 HCD-FX10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > C210 1-126-925-91 ELECT 470uF C211 1-126-964-11 ELECT 10uF D824 8-719-988-61 DIODE 1SS355TE-17 D825 8-719-988-61 DIODE 1SS355TE-17 C212 1-162-921-11 CERAMIC CHIP...
  • Page 88 HCD-FX10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC602 8-759-649-89 IC MC4558CD R613 1-216-829-11 METAL CHIP 4.7K 1/10W R614 1-216-829-11 METAL CHIP 4.7K 1/10W IC603 6-600-014-01 IC TORX141L (OPTICAL DIGITAL IN)
  • Page 89 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > C117 1-164-346-11 CERAMIC CHIP C119 1-162-927-11 CERAMIC CHIP 100PF D811 8-719-079-89 DIODE SML-020MDT-T86 (DISC1) C120 1-126-947-11 ELECT...
  • Page 90 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C201 1-125-898-91 CERAMIC CHIP 0.22uF C286 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C202 1-125-898-91 CERAMIC CHIP 0.22uF C287 1-162-966-11 CERAMIC CHIP 0.0022uF 10%...
  • Page 91 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C367 1-164-156-11 CERAMIC CHIP 0.1uF C548 1-216-864-11 SHORT CHIP C368 1-165-908-11 CERAMIC CHIP C549 1-107-726-91 CERAMIC CHIP 0.01uF C551 1-107-726-91 CERAMIC CHIP 0.01uF...
  • Page 92 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 C912 1-113-907-51 CERAMIC 0.0022uF 20% 250V 0 C913 1-117-693-11 CERAMIC 100PF 250V D106 6-500-260-01 DIODE P6SMB39AT3 D107 6-500-260-01 DIODE P6SMB39AT3...
  • Page 93 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB511 1-216-295-91 SHORT CHIP L116 1-457-077-11 AIR-CORE COIL L121 1-456-680-11 INDUCTOR 10uH FB512 1-216-295-91 SHORT CHIP L122 1-456-680-11 INDUCTOR 10uH...
  • Page 94 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q901 8-729-140-04 TRANSISTOR 2SB1116A-L R191 1-220-942-11 METAL CHIP 1/4W Q921 8-729-142-51 TRANSISTOR 2SD1616A-TP-LK R192 1-220-942-11 METAL CHIP 1/4W R193 1-220-942-11 METAL CHIP...
  • Page 95 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R325 1-216-864-11 SHORT CHIP R400 1-216-845-11 METAL CHIP 100K 1/10W R326 1-216-864-11 SHORT CHIP R401 1-216-845-11 METAL CHIP 100K 1/10W...
  • Page 96 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R514 1-216-821-11 METAL CHIP 1/10W R581 1-216-809-11 METAL CHIP 1/10W R515 1-216-809-11 METAL CHIP 1/10W R582 1-216-809-11 METAL CHIP 1/10W...
  • Page 97 HCD-FX10 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R673 1-216-833-11 METAL CHIP 1/10W R775 1-216-841-11 METAL CHIP 1/10W R674 1-216-864-11 SHORT CHIP R789 1-216-809-11 METAL CHIP 1/10W R790...
  • Page 98 HCD-FX10 MAIN MODE MOTOR RELAY ROLLER MOTOR SENSOR 3 7 63 1515 0 ST ENCODER STOCKER MOTOR SW (1) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark RB505 1-233-576-11 RES, CHIP NETWORK 100 (3216) < CONNECTOR >...
  • Page 99 HCD-FX10 SW (2) SW (3) SW (4) 3 7 63 1515 0 Ref. No. Part No. Description Remark ************************************************************ 1-686-728-13 SW (2) BOARD ************ < SWITCH > S713 1-786-382-21 SWITCH, PUSH (1 KEY) (DISC IN (8/12cm)) S714 1-786-382-21 SWITCH, PUSH (1 KEY) (DISC IN (8cm))
  • Page 100 HCD-FX10 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 101 HCD-FX10 3 7 63 1515 0 US Model Canadian Model SERVICE MANUAL Ver. 1.1 2005.11 SUPPLEMENT-1 Subject : Addition of ELECTRICAL ADJUSTMENT L 13942296513 u163 9-879-623-81 http://www.xiaoyu163.com...
  • Page 102 HCD-FX10 ELECTRICAL ADJSTMENT 3 7 63 1515 0 Checking Location: DMB10 board (Side A) DVD SECTION When the base unit is replaced, perform the adjustment and the measurement as shown below in this order. 1) MIRROR TIME ADJUSTMENT (See page 23)
  • Page 103 HCD-FX10 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 104 HCD-FX10 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Table of Contents