CONTENTS Chapter 1: General Information 1-1. Document Information ................3 1-2. General Guidelines ................3 1-3. Important Notice ..................3 1-3-1. Follow the regulations and warnings ............. 3 1-3-2. Be careful to the electrical shock ............3 1-3-3. Electro static discharge (ESD) ............... 3 1-3-4.
Service Manual Model No.: HL22F2a Chapter 1: General Information 1-1. Document Information Document format: Adobe PDF Author: WangHaiyan Compiler: Bao Qinghong 1-2. General Guidelines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
Service Manual Model No.: HL22F2a components commonly are called Electrostatically Sensitive (ES) Devices. The following electros static discharge (ESD). Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
Page 6
Service Manual Model No.: HL22F2a 1. Always unplug the receiver AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c.
Service Manual Model No.: HL22F2a 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
Page 8
Service Manual Model No.: HL22F2a Caution: A “caution” is used when there is danger that the reader, through incorrect restart(part of) a procedure. Warning: A “warning” is used when there is danger of personal injury. Reference: A “reference” guides the reader to other places in this binder or in this manual, where...
Page 9
Service Manual Model No.: HL22F2a HL22FW2a HL22FP2a Model HL22F2a HL22F2a 21.6 inch 21.6 inch Screen Size 21.6 inch 21.6 inch 21.6 inch 21.6 inch 16:9 16:9 Aspect Ratio 16:9 16:9 16:9 16:9 1366x768 1366x768 Resolution 1366x768 1366x768 1366x768 1366x768 5 (GRAY TO 5 (GRAY TO 5 (GRAY TO 5 (GRAY TO...
Service Manual Model No.: HL22F2a Chapter 4. Location of Controls and Components 4-1. Board Location B Board A Board Parts number Description A Board DC14C0E0D00M Main Board(0090724734) B Board 094001244B Power Board 4-2. Main Board...
Service Manual Model No.: HL22F2a 4-2-1 Function Description: Main Board Main board connector Power connectors (CN3) Pin number Signal name +12V +12V Notes: CN1-Pin 3: Backlight on/off: The system can turn on or turn off the backlight of TFT LCD Panel through the power supply unit path.
Page 16
Service Manual Model No.: HL22F2a LVDS Connector (CN4) Pin number Signal name Description LVDS_D0E_N LVDS EVEN 0 - Signal LVDS_D0E_P LVDS EVEN 0 + Signal Ground LVDS_D1E_N LVDS EVEN 1 - Signal LVDS_D1E_P LVDS EVEN 1 + Signal Ground LVDS_D2E_N LVDS EVEN 2 - Signal LVDS_D2E_P LVDS EVEN 2 + Signal...
Service Manual Model No.: HL22F2a 4-3. Power Board 4-3-1. Function description: To supply power for Panel and Main Board. INPUT CONNECTOR (CN10) Power supply and Inverter Connector CN10 number Signal name Description Ground Ground Power Power Other Connector Power supply for panel (CNC2) 4-4.
Page 18
Service Manual Model No.: HL22F2a Panle LVDS Connector (CNC4) PIN # SIGNAL NAME DESCRIPTION No contact (For AUO internal use) No contact (For AUO internal use) No contact (For AUO internal use) Power Ground RXIN0- Negative LVDS differential data input (0) RXIN0+ Positive LVDS differential data input (0) Power Ground...
Service Manual Model No.: HL22F2a Connection Option 1 Note Set VCR output switch to channel 3 or 4 and then tune If your DVD player does not have the TV to the same channel number. component video output, use S-Video. Connection Option 2 L -AUDIO- R Connect the audio and video cables from the VCR’s...
Service Manual Model No.: HL22F2a How to use VIDEO L -AUDIO- R ANT IN Turn on the computer and the TV. Use INPUT on the remote control to select VGA or HDMI source. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in VGA mode.
Service Manual Model No.: HL22F2a How To Use If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p. If the source device does not support Auto HDMI, you need to set the output resolution appropriately.
Service Manual Model No.: HL22F2a Analog Audio Cable (Stereo to RCA type) (not supplied with the product) Connecting Headphones You can connect a set of headphones to your set if you wish to watch a TV programmer without disturbing the other people in the room. Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set.
Service Manual Model No.: HL22F2a 6. Operation Instructions 6-1 Front panel controls INPUT MENU VOL- VOL+ POWER 1 POWER Press to turn on and off the TV. Press to access the input source mode. Press repeatedly to change the source to the one 2 INPUT you want to watch.
Service Manual Model No.: HL22F2a Battery loading 1. Slide open the cover of the battery compartment on the back of the remote controller. 2. Load two 7# (AAA) alkaline batteries in the compartment, (plus and minus poles to respective mark) 3.
Service Manual Model No.: HL22F2a Chapter 8. Measurements and Adjustments 8-1. Service Mode 8-1-1.How to enter into Service Mode The way to the factory mode menu: Step 1: Press Menu, Step 2: Input 8893, Step 3: Press “OK” System will be into the factory mode menu when 3 steps above are done. 8-1-2.How to exit If you want to exit this factory menu, please press the button ”Exit”...
Service Manual Model No.: HLC22F2a 8-2-2. Video Auto Color The option could only be used in the VGA and Component model. When we found the color in the two models was abnormal. Then we can use the function to adjust it automatically. Color Temperature The function could adjust the Color Temperature, used when debugging...
Service Manual Model No.: HL22F2a 8-2-3. Audio Dolby Banner: When turn it “ON”, the model will be in Dolby authentication state. Compression: Compression style. RF atv line AV/S-Video/YPbPr/VGA Compression Factor: Compression state. Downmix: output model. MTS System: used when debugging. The parameters only used when 8-2-4.
Page 44
Service Manual Model No.: HL22F2a Factory Scan: According to ANTENNA-ANALOG---ANTENNA-DIGITAL---CABLE- ANALOG---CABLE- DIGITAL to search channels, used only in project debugging. Tuner Diagnostic: Project debugging setting, used to inspect the audio function.
Service Manual Model No.: HL22F2a 8-2-5. Gamma Gamma: Bright GAMMA0.8 Middle default settings in the program Dark GAMMA1.2 8-2-6. Backlight Backlight: adjust the backlight.
Service Manual Model No.: HL22F2a 8-2-7. Function Burning Mode: Turn it “ON” to enter the aging model, This is for factory run-in testing. The screen would display red, green, blue and black screen repeatedly. Each color screen could be exam at that time. Clean Storage The function could make the model turn back to the factory default setting.
Page 47
Service Manual Model No.: HL22F2a Remark: The date of the chart only is an example, please don’t adjust the factory mode base on it.
Service Manual Model No.: HL22F2a Chapter 9. Trouble shooting 9-1. Simple check Verify if the television is properly plugged Verify if the television is properly supplied power No picture/ No sound Verify if electricity is available. Verify if correct signals are input Press INPUT button to change signal input to TV input Blank screen Restart the television of power supply is interrupted...
Service Manual Model No.: HL22F2a 9-3. Mainboard Failure Check Symptom: No Sound No Sound (All Mode) Fail Check the input Change Source input Source Pass Fail Check Re-soldering or change input/output IC U13 Pass Fail Check Re-soldering or change input/output IC U55 Pass Fail...