NEC NP1250 Network Setup Manual
Lcd projector wpa setting guide
Hide thumbs
Also See for NP1250:
- User manual (183 pages) ,
- Network setup manual (44 pages) ,
- Installation manual (10 pages)
Related Manuals for NEC NP1250
Summary of Contents for NEC NP1250
- Page 1 LCD Projector NP3250/NP2250/ NP1250/NP3250W WPA Setting Guide Security Network r i t y Supported Authentication Method WPA-PSK WPA-EAP WPA2-PSK WPA2-EAP...
-
Page 2: Table Of Contents
(4) Notwithstanding article (3), NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector. © NEC Display Solutions, Ltd. 009 Reproduction, modification, and other uses are prohibited without the permission of NEC Display Solutions, Ltd. -
Page 3: Introduction
• When you set WPA-EAP or WPA-EAP, be sure to set [DATE, TIME PRESET] before installing digital certificates. If setting of [DATE, TIME PRESET] is not correct, a message “authentication error” will be displayed. • To install digital certificates on the projector, use a USB memory device in the market. Introduction Encryption EAP type... - Page 4 (authentication method, encryption type, EAP type, and digital certificates). • For using the on-screen menu on the projector, see the “User’s Manual” (PDF) on the supplied CD-ROM. • See the supplied “Wired and Wireless Network Setup Guide” for instructions on set- ting IP address, subnet mask, SSID, and WEP on the projector.
-
Page 5: Setting.wpa-Psk.or.wpa2-Psk
1. Setting WPA-PSK or WPA2-PSK From the on-screen menu on the projector, select [SETUP] → [INSTALLATION()] tab → [NETWORK SETTINGS] screen and follow the instructions below. ➊ Display the [NETWORK SETTINGS] screen. • See page 17 of “Wired and Wireless Network Setup Guide”... - Page 6 ➏ Use the SELECT ▼▲ button to select a connecting SSID, and then press the SELECT ▶ button to select [OK]. Finally press the ENTER button. • Select the SSID for which WPA-PSK or WPA-PSK is set. • Select [INFRASTRUCTURE ( WORK TYPE].
- Page 7 ⓬ Use the SELECT ▼ button to select the [KEY] field and press the ENTER but- ton. The character entry screen (software keyboard) will be displayed. Set a key. • A key must be between 8 and 3 characters in length. •...
-
Page 8: Setting.date,.Time.preset
• The projector has a built-in clock. The clock will keep working for about weeks after the main power is turned off. If the main power is off for weeks or more, the built-in clock will cease. -
Page 9: Setting.wpa-Eap.or.wpa2-Eap
After completing saving the file, remove the USB memory device from the computer. Important: • The file formats of digital certificate that are supported by the projector are DER and PKCS#1 only. • The projector cannot handle any digital certificate whose file size exceeds 8 KB. - Page 10 ❼ Use the SELECT ▼▲ button to select [TKIP] or [AES] and press the ENTER button. Select [TKIP] or [AES] according to the setting for your access point. ❽ Use the SELECT ▲ button to select the [SECURITY] tab and press the SELECT ▶...
-
Page 11: Enter Button
A password must be 1 character or more and 3 characters or less. The selected digital certificate file will be in- stalled on the projector. • When the root CA certificate is not included in the file that was selected in Step ⓫, proceed to Step ⓭. - Page 12 HINT: Clearing the digital certificate that is installed on the projector To clear the digital certificate installed on the projector, follow the steps below. By doing the following procedure, all the digital certificates for the currently displayed profile will be cleared.
- Page 13 HINT: • The PKCS#1 format digital certificate including a CA certificate will be installed as a root CA certificate. ② Selecting [PEAP-MSCHAPv2] for [EAP TYPE]: ❾ From the [AUTHENTICATION] page, use the SELECT ▼ button to select [EAP TYPE] field and press the ENTER but- ton.
- Page 14 USB memory device and press the ENTER button. • Select your root CA certificate here. The selected digital certificate will be installed on the projector. ① Select a USB memory and ⓯ After completing required settings, use the SELECT ▼ button to select [OK] and press the ENTER button.
- Page 15 HINT: Clearing the digital certificate that is installed on the projector To clear the digital certificate installed on the projector, follow the steps below. By doing the following procedure, all the digital certificates for the currently displayed profile will be cleared.
-
Page 16: Checking.authentication.status.on.[Information].Screen
4. Checking Authentication Status on [INFORMATION] Screen You can check your authentication status on the [INFORMATION] screen from the on- screen menu. ❶ Display the [INFORMATION] screen. • Use the first tab (main menu) to select [IN- FORMATION]. ❷ Select the [WIRELESS LAN(1)] tab. The current authentication status will be dis- played in the [AUTHENTICATION] field.