Download
Share
Print this page
Epson SC-F9200 Series Setup Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. SC-F9200 series
  6. Setup manual
Epson SC-F9200 Series Setup Manual

Epson SC-F9200 Series Setup Manual

Hide thumbs Also See for SC-F9200 Series:

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
SC-F9200 Series
Rev.A
SETUP MANUAL
SC-F9200 Series
SE Group Confidential (Related Staff Only)
1

Advertisement

loading

Related Manuals for Epson SC-F9200 Series

Summary of Contents for Epson SC-F9200 Series

  • Page 1 SC-F9200 Series Rev.A SETUP MANUAL SC-F9200 Series SE Group Confidential (Related Staff Only)
  • Page 2 SC-F9200 Series Rev.A IMPORTANCE • Please inform the user of the next page certainly! • Please print and pass the next page to user and encourage the points of caution.
  • Page 3 SC‐F‐Series SC-F9200 Series Rev.A Ink refill ■ Check ink levels Replace chip unit with new one attached When this message appears, new ink pack. check ink level of the tank Ink level is more than 70mm: which is indicated by Recommends to continue using the printer until the ink level reaches 70mm from the bottom.
  • Page 4 SC-F9200 Series Rev.A About This Manual The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Symbols Used in this Manual C A U T I O N...

  • Page 5: Revision Status

    SC-F9200 Series Rev.A Revision Status Revision Date of Issue Description April 22,2015 Temporary release for unit July 10,2015 First release for MP unit...
  • Page 6 SC-F9200 Series Rev.A 1.1 Caution for Installation  Installation Serviceman must set it （Not User） 1.2 Choosing a Place for the Printer  Instructions for Placing the Printer • keep adequate room as shown. • Choose a level and stable location that can support the weight of the printer (about 288 kg).
  • Page 7 SC-F9200 Series Rev.A 1.4 Inside of carton box Printer Media Feeding Unit, Auto Take-up Reel Unit Epson Genuine Ink Supply System...
  • Page 8 SC-F9200 Series Rev.A 2. Setup Flow Assemble according to the following flow charts. Customer Stand Printer Installation Media Feeding Unit Auto Take-up Reel Unit Service engineer Only Frame of Media Guide Bar (without Guide bar) Ink Supply System Media Guide Bar...
  • Page 9 SC-F9200 Series Rev.A <<Stand>> C H E C K It is recommended to assemble the stand by 3persons. P O I N T Remove the tapes. Insert the strut into the stands with supporting the stands. Tighten 4screws...
  • Page 10 SC-F9200 Series Rev.A Check the markings of L & R on both stands and strut. Tighten 4screws with supporting the stands. Tighten 1screw Tighten 2screws...
  • Page 11 SC-F9200 Series Rev.A <<Printer>> Take out the Carrying Bar Insert the Carrying Bar Set the carrying bar for printer to be between two screws the carrying bar, locate the screws upside.
  • Page 12 SC-F9200 Series Rev.A Confirm the stand to be fixed. • Before moving the printer, be sure the stand is fixed in place. C A U T I O N • Be sure the casters are floating on floor. Lift the printer on the stand •...
  • Page 13 SC-F9200 Series Rev.A Tighten 3screws with washer Peel tapes off as below. Open the front cover. C A U T I O N Be careful not to trap your hands or fingers when opening or closing the front cover. Pressing the tabs on both sides of the media holding plates to center as shown.
  • Page 14 SC-F9200 Series Rev.A Remove 2screws, and remove the plate below C H E C K P O I N T Dispose 2screws and this plate. plate...
  • Page 15 SC-F9200 Series Rev.A <<Media Feeding Unit>> Fix the parts at both sides by tightening screws (total: 4pcs). Rear side Set the Media Feeding Unit firstly from the left side as below. C A U T I O N Carry the Media Feeding Unit (approx. 34.3 kg) using 2persons,...
  • Page 16 SC-F9200 Series Rev.A Slide core holder and tighten 5screws. Tighten 4screws temporarily until parallel adjustment is completed. C A U T I O N Temporarily tighten (Only home side) Set cable by clamps...
  • Page 17 SC-F9200 Series Rev.A Open the cover Plug the connector. Set the cable by clamps. Close the cover...
  • Page 18 SC-F9200 Series Rev.A <<Auto Take-up Reel Unit>> Tighten each 2screws (total: 4pcs) Set Reel Unit...
  • Page 19 SC-F9200 Series Rev.A Slide core holder and tighten 5screws Tighten 4screws temporarily until parallel adjustment is completed. C A U T I O N Temporarily tighten (Only home side) Set the cable through the bottom clamp behind the printer. Plug the connector, fix it by 2screws.
  • Page 20 SC-F9200 Series Rev.A <<Media Guide Bar (Only two frames for Right and Left)>> It was already assembled at factory. Set 2screws temporarily, and set parts on stand, and slide it to right. Tighten 2screws. Slide it to right Temporarily tighten...
  • Page 21 SC-F9200 Series Rev.A Tighten 2screws. Temporarily tighten Tighten 1 more screw...
  • Page 22 SC-F9200 Series Rev.A Tighten 2screws temporarily Temporarily tighten Position the part on the stand, and slide it to left. Tighten 2screws. Slide it to left Tighten...
  • Page 23 SC-F9200 Series Rev.A 2.7 Stand / Ink Tank / Waste Ink Tube / Waste Tank • Silver ones : 6pcs • Blue ones : 4pcs You can use both Blue ones below. After 100units, This screws will be changed (Running change)
  • Page 24 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (1) Home and Front side (1pcs) 1. Remove tape on tube. 2. Make sure 2 holes are smaller. 3. Loosen 2 screws and slide the plate to fix onto the stand.
  • Page 25 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (2) Full and Front side (1pcs) 1. Make sure 2 holes are bigger. 2. Tighten 2 screws temporarily. D2 x 2 Temporarily tighten 3. Slide the plate & tighten 2 screws.
  • Page 26 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (3) Full and Rear side (2pcs) 1. Make sure “left parts” and “right parts”. 2. Tighten 2 screws temporarily to keep 1 ~ 2 mm distance. Left parts Right Parts D2 x 2...
  • Page 27 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (3) Full and Rear side (2pcs) 3. Slide the plate and tighten 2 screws temporarily. 4. Tighten 4 screws. D2 x 2 Temporarily tighten Tighten 4 screws...
  • Page 28 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (3) Full and Rear side (2pcs) 1. Make sure “left parts” and “right parts”. 2. Tighten 2 screws temporarily to keep 1 ~ 2 mm distance. Left parts Right Parts D2 x 2...
  • Page 29 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (3) Full and Rear side (2pcs) 3. Slide the plate and tighten 2 screws temporarily. 4. Tighten 4 screws. Temporarily tighten D2 x 2 Tighten 4 screws...
  • Page 30 SC-F9200 Series Rev.A Attach 6pcs plates for strengthen stand (4) Home and Rear side (2pcs) 1. As the same as (3) Full and Rear side (2pcs) 2. Tighten total 8 screws. Right Parts Left parts D2 x 8...
  • Page 31 SC-F9200 Series Rev.A 1. Tighten 1 screw to fix Ink Tube Holder. 2. Fix the plate by tightening 3 screws. Ink Tube Holder F x 1 To align screw and  Plate big hole D2 x 3 difficult to access Ink Tube Holder Top screw is difficult to access, so tighten middle one and bottom one, first.
  • Page 32 SC-F9200 Series Rev.A Loosen 3 screws a little bit, and make sure the plate is lower.
  • Page 33 SC-F9200 Series Rev.A 1. Hook the plate to fix. (1 hook) as below. 2. Tighten 3 screws. F x 2 G x 1...
  • Page 34 SC-F9200 Series Rev.A 1. Hook the plate to fix (2 hooks) as below. ** Not to pinch the Waste Ink Tube. 2. Tighten 4 screws temporarily. Waste Ink Tube F x 2 Temporarily tighten Temporarily tighten F x 2 Temporarily tighten...
  • Page 35 SC-F9200 Series Rev.A 1. Hook the plate to fix as below.(1 hooks) 2. Tighten 3 screws.(G: 1pcs, F: 2pcs) 3. Tighten 4 temporarily-tightened-screws of the previous page.(F: 4pcs) F x 2 G x 1...
  • Page 36 SC-F9200 Series Rev.A 1. Through Waste Ink Tube into hole. 2. Hook the plate to fix (2 hooks) as below. Through Waste Ink Tube...
  • Page 37 SC-F9200 Series Rev.A 1. Tighten 2 screws on the rear side. 2. Tighten 5 more screws as the same order as below photos. G x 2 rear side of plate Left side of plate bottom side of printer Left side of...
  • Page 38 SC-F9200 Series Rev.A << Left Tanks >> 1. Loosen 2 screws and make sure Front Plate is low. 2. Loosen 4 screws and make sure the plates to be able to move up/low and left/right. Loosen Left Right tanks tanks...
  • Page 39 SC-F9200 Series Rev.A 1. Tighten 2 long screws temporarily. Not to  touch Temporarily tighten Temporarily tighten...
  • Page 40 SC-F9200 Series Rev.A 1. Make sure the color index on the plate. 2. Put each CSIC on each slider. 3. Set only Cyan and Black Ink Tanks into Ink Holder as the same order as the color index. ****Set the tank...
  • Page 41 SC-F9200 Series Rev.A Set to fit between cut position of Ink Tank and hook of Ink Holder. Please do NOT be down all levers before adjustment tank height. IMPORTANCE OK!! NG!! Set Ink Tank again Tighten 2 Blue screws temporarily.
  • Page 42 SC-F9200 Series Rev.A 1. Raise the plate softly and Tighten 2 screws. 2. Insert thickness-gauges(2.0mm) with raising the tanks. 3. Tighten 2 Blue screws to fix the tanks.( only Black&Cyan) Tighten Cyan Black Tighten Tighten To fix the tank To fix the tank...
  • Page 43 SC-F9200 Series Rev.A << Rough Height Adjustment>> 1. Tighten Right Long Screw until the thickness(2.0mm) gauges can be moved smoothly at 2 locations(Black and Cyan). 2. Tighten Left Long Screw as the same as the right one. 3. Loosen 2...
  • Page 44 SC-F9200 Series Rev.A << Detail Height Adjustment>> 1. Tighten Right Long Screw until the thickness gauges(2.0mm) can be moved smoothly, Again at 2 locations(Black and Cyan). 2. Tighten Left Long Screw as the same as the right one. 3. Make sure the thickness gauge(2.5mm) can’t be passed...
  • Page 45 SC-F9200 Series Rev.A 1. Set the other tanks. 2. Tighten 4 screws to fix the tanks.. (Yellow => Magenta => Cyan => Black) I x 2 Tighten to fix Tighten to fix Yellow 2. Magenta Tighten to fix Tighten to fix...
  • Page 46 SC-F9200 Series Rev.A 1. Make sure thickness-gauge(2.0mm) can be passed and thickness-gauge(2.5mm) can’t be passed Again at 2 locations(Black and Cyan). 2.0mm => Can be Passed 2.5mm => Can’t be Passed...
  • Page 47 SC-F9200 Series Rev.A Check the vertical position of Ink Tank. If it is enough to hold/insert the Ink Tank, please set C A U T I O N this Ink Tank again. OK!! NG!! Set Ink Tank again Check the front and rear position of Ink Tank.
  • Page 48 SC-F9200 Series Rev.A 1. Tighten 2 screws. 2. Push 4 tanks by hand softly. 3. Tighten 2 more screws without pushing by hand. Tighten Tighten Tighten Tighten...
  • Page 49 SC-F9200 Series Rev.A 1. Loosen 2 screws, again. 2. Tighten 2 screws with rising the plate softly. 3. Lock down all levers. Loosen Loosen Tighten Tighten...
  • Page 50 SC-F9200 Series Rev.A <Right Tanks> same as 1. As the <Left Tanks>. 2. Tighten 4 screws and adjust <Right tanks>. Right Tanks I x 4 Blue : 2pcs * Silver : 2pcs...
  • Page 51 SC-F9200 Series Rev.A 1. Hook the plate to fix (1 hook) as below 2. Tighten 2 screws. 3. Insert the plate into 2 dowels. 4. Tighten 4 more screws. Left side of plate G x 6 Right side of plate...
  • Page 52 SC-F9200 Series Rev.A 1. Tighten 2 screws. 2. Loosen 2 screws and lower the plate. 3. Tighten 2 screws with pushing down the plate softly. I x 2 Tighten Loosen Loosen Tighten...
  • Page 53 SC-F9200 Series Rev.A Tighten 3 screws with rising the plate softly.
  • Page 54 SC-F9200 Series Rev.A Put the plate and tighten 4 screws. J x 4...
  • Page 55 SC-F9200 Series Rev.A 1. Remove protect sheets both surfaces on the acrylic plate. 2. Put acrylic plate and tighten 5 screws. Protect Sheet Protect Sheet H x 5...
  • Page 56 SC-F9200 Series Rev.A Peel off the tapes on the tube. Unlock the 2clamps...
  • Page 57 SC-F9200 Series Rev.A 1. Cover the plate over Waste Ink Tube. 2. Make sure the hook is under Upper Clamp and lock it. 3. Make sure the hook is above Lower Clamp and lock it. Plate Upper Clamp Upper Clamp...
  • Page 58 SC-F9200 Series Rev.A Fix Waste ink Joint of the tube onto the plate as below. Waste ink joint...
  • Page 59 SC-F9200 Series Rev.A Set Stopper as below. Stopper 2 hooks C H E C K The lid of the Waste Ink Bottle is required when disposing P O I N T of the waste ink. Keep the lid. Do throw it away.
  • Page 60 SC-F9200 Series Rev.A Stick the label for your territory on the English label if necessary...
  • Page 61 SC-F9200 Series Rev.A Hold the Media guide bar in both hand, tighten 2screws The media guide bar is heavy. A minimum of 2persons is C A U T I O N required for assembly. Tighten E x 2 Tighten 2screws...
  • Page 62 SC-F9200 Series Rev.A <<Parallel Adjustment of the Media Feeding Unit>> C H E C K When the film will be reused, the adhesive side may be P O I N T soiled. Soak a lint-free cloth in water, wring it out, and then use it to wipe away the dust and lint stuck to the reverse side.
  • Page 63 SC-F9200 Series Rev.A <<Media Feeding Unit>> Pass 2films from Rear side Release after checking “L”, “R”. Open Remove protective sheet, and put it after aligned screws Loosen 4screws...
  • Page 64 SC-F9200 Series Rev.A Remove protective sheet, Loosen knobs, and put it after aligned (2) and and fix knobs after aligned (4) screws Frame of Board box Frame of Board box Loosen knobs, and slide it...
  • Page 65 SC-F9200 Series Rev.A Turn counter clockwise Turn clockwise until No visible “A” Pass film into Core Pass film from Rear Set Core Align a film to b film (Rear and Front side)
  • Page 66 SC-F9200 Series Rev.A Attach Counterweight, and Move film to Home side, and Measure and note value Check value -> Same = No need to adjust ->different = Need to adjust...
  • Page 67 SC-F9200 Series Rev.A Remove counterweight Adjustment to turn screw Loosen knob, and slide it, Pull film Tighten 4screws after adjust same value Remove core (with film)
  • Page 68 SC-F9200 Series Rev.A <<Auto take-up Reel Unit>> Loosen 4screws Loosen knobs, and fix knobs after aligned Frame of after heater Turn counter clockwise Frame of After heater...
  • Page 69 SC-F9200 Series Rev.A Set Core Pass film from Front To through Media Guide Bar Turn clockwise until No visible “A” IMPORTANCE After Heater Paper Media Guide Bar Roll Core...
  • Page 70 SC-F9200 Series Rev.A Move film to Home side, and Align a film to b film Check value (Rear and Front side) -> Same = No need to adjust Attach Counterweight, and ->different = Need to adjust Measure and note value...
  • Page 71 SC-F9200 Series Rev.A Adjustment to turn screw Remove counterweight Remove core (with film) Tighten 4screws after adjust same value...
  • Page 72 SC-F9200 Series Rev.A Pass film from Front Align a film to b film To use Media Guide Bar (Rear and Front side) Attach Counterweight, and Measure and note value IMPORTANCE After Heater Paper Media Guide Bar Roll Core cofidencial...
  • Page 73 SC-F9200 Series Rev.A Move film to Home side, and Loosen 2screws Check value to use small hexagon wrench -> Same = No need to adjust ->different = Need to adjust...
  • Page 74 SC-F9200 Series Rev.A Adjustment to turn screw Remove counterweight Remove core (with film) Tighten 2screws after adjust same value...
  • Page 75 SC-F9200 Series Rev.A <<Connecting the Power Cable>> • Use only the type of power source indicated on the C A U T I O N printer’s label. Install the clamp Connecting 2 power cables at Printer Fasten the cables by 2clamps.
  • Page 76 SC-F9200 Series Rev.A 2.11 Fill the ink C A U T I O N Wear security goggle and globes, wash your skin immediately when the ink adheres to your skin. C A U T I O N Shake the ink packs of all colors well to prevent the ink settlement.
  • Page 77 SC-F9200 Series Rev.A Fill the ink. C A U T I O N • Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink tanks.
  • Page 78 SC-F9200 Series Rev.A 2.12 Firmware update Turn ON the printer in the F/W update mode. Push “ON” while pressing [Media setup] + [Media feed] +[Maintenance]. PUSH IMPORTANCE Check the current Firmware version. Update the latest FW if the FW is not latest one.
  • Page 79 SC-F9200 Series Rev.A Turn ON the printer in the Normal mode. Set the printer setting. (Language, date, time etc.) Starting Ink Charge. ( Approximately 50 min) Check the nozzle check pattern. If nozzle missing, do cleaning.
  • Page 80 SC-F9200 Series Rev.A *** If necessary *** <<Check the Ink Tank position>> 1. Turn ON the printer in the Serviceman Mode. Push “ON” while pressing [Menu] + [Back] + [OK]. IMPORTANCE 2. [SELF TESTING] -> [Mech Adjustment] ->[Sensor Check] -> [ILS] 3.
  • Page 81 SC-F9200 Series Rev.A  Trouble shooting for ink charge 1. Check the Ink Tank condition according to the following tables. 2. If it is enough to set the Ink Tank, please set this Ink Tank again. Trouble Cause Hook of Ink Tank comes off •...