Related Manuals for Toro 74391
Summary of Contents for Toro 74391
- Page 1 Form No. 3358-944 Rev A TimeCutter ® Z5000 Riding Mower Model No. 74391—Serial No. 280000001 and Up Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or Contents additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Introduction..............2 identifies the location of the model and serial numbers Safety ................ -
Page 3: Safety
Safety Servicing the Engine Oil ........25 Servicing the Spark Plug ........27 Cleaning the Blower Housing......27 Safe Operation Practices Fuel System Maintenance ........28 for Ride-on (riding) Rotary Replacing the Fuel Filter ........28 Electrical System Maintenance........ 29 Lawnmower Machines Charging the Battery........... - Page 4 ◊ lack of awareness of the effect of ground – stay alert for humps and hollows and other conditions, especially slopes; hidden hazards; ◊ incorrect hitching and load distribution. • Use care when pulling loads. – Use only approved drawbar hitch points. Preparation –...
-
Page 5: Toro Riding Mower Safety
If tires lose traction, disengage the blades and proceed slowly off the slope. The following list contains safety information specific to Toro products or other safety information that you must • Follow the manufacturer’s recommendations for know that is not included in the CEN standard. -
Page 6: Slope Chart
Slope Chart... -
Page 7: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 114-1606 1. Entanglement hazard, belt—keep all guards in place. 106-8717 1. - Page 8 112-9751 1. Parking position 4. Neutral 2. Fast 5. Reverse 3. Slow 110-6824 1. Height-of-cut 112-9840 1. Read the Operator’s 3. Remove the ignition key Manual. and read the instructions before servicing or performing maintenance. 2. Height of cut 115-2500 1.
- Page 9 Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or 7. Wear eye protection; smoking. explosive gases can cause blindness and other injuries 3.
-
Page 10: Product Overview
Product Overview Figure 3 1. Footrest 4. Control panel 7. Rear drive wheel 10. Anti-scalp roller 2. Height of cut lever 5. Motion control levers 8. Washout fitting 11. Front caster wheel 3. Fuel gauge 6. Operator seat 9. Mower deck G005180 Figure 4 1. -
Page 11: Controls
Controls reverse; wheel speed is proportional to the amount the lever is moved. Move the control levers outward from Become familiar with all of the controls in Figure 3, the center to the park position and exit the machine Figure 4, and Figure 5 before you start the engine and (Figure 15). -
Page 12: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. Think Safety First Please carefully read all of the safety instructions and decals in the safety section. Knowing this information could help you, your family, pets or bystanders avoid injury. - Page 13 In certain conditions, gasoline is extremely In certain conditions during fueling, static flammable and highly explosive. A fire or electricity can be released causing a spark explosion from gasoline can burn you and which can ignite the gasoline vapors. A fire others and can damage property.
-
Page 14: Checking The Engine Oil Level
Add the correct amount of gas stabilizer/conditioner allows gasoline to expand. Do not fill the fuel tank to the gas. completely full. 4. Install the fuel tank cap securely. Wipe up any Note: A fuel stabilizer/conditioner is most effective gasoline that may have spilled. when mixed with fresh gasoline. -
Page 15: Operating The Blades
3. Move the throttle lever to Choke before starting a cold engine (Figure 11). Note: A warm or hot engine may not require choking. G005058 G005057 Figure 12 1. Control panel 4. Off 2. Ignition key—run position 5. Run 3. Ignition key—start position 6. Start 5. -
Page 16: Stopping The Engine
The Safety Interlock System If safety interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. • Do not tamper with the interlock switches. G005059 • Check the operation of the interlock switches daily and replace any damaged switches before operating the machine. -
Page 17: Driving Forward Or Backward
Driving Forward or Backward To turn, release pressure on the motion control lever toward the direction you want to turn (Figure 15). The throttle control regulates the engine speed as The farther you move the motion control levers in measured in rpm (revolutions per minute). Place either direction, the faster the machine will move in the throttle control in the Fast position for best that direction. -
Page 18: Positioning The Seat
Adjusting the Motion Control Levers Adjusting the Height The motion control levers can be adjusted higher or lower for maximum operator comfort. 1. Remove the 2 bolts holding the control lever to the control arm shaft (Figure 18). 2. Move the control lever to the next set of holes. Secure the lever with the 2 bolts (Figure 18). -
Page 19: Side Discharge Deflector
Side discharge performance can be improved by replacing the mulching blades with standard cutting blades obtained from your local authorized Toro dealer. To maintain optimum mulching performance, always install the mulching blades that are shipped with this unit when changing back to mulching operation. -
Page 20: Operating Tips
Open holes in the mower expose you and others to thrown debris which can cause severe injury. • Never operate the mower without hardware mounted in all holes in the mower housing. • Install the hardware in the mounting holes when you remove the mulching baffle. -
Page 21: Blade Maintenance
If enhances decomposition and fertilization. a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. Mow at Correct Intervals Normally, mow every four days. But remember, grass grows at different rates at different times. -
Page 22: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the safety interlock system. • Check the air cleaner for dirty, loose or damaged parts. •... -
Page 23: Premaintenance Procedures
Premaintenance Lubrication Procedures Greasing the Bearings Raising the Seat Service Interval: Every 25 hours—Grease all lubrication points. Make sure the motion control levers are locked in the Grease Type: No. 2 General Purpose Lithium Base park position. Lift the seat forward. Grease The following components can be accessed by raising 1. -
Page 24: Engine Maintenance
Engine Maintenance 4. Connect a grease gun to each fitting (Figure 23 and Figure 24). Pump grease into the fittings until grease begins to ooze out of the bearings. Servicing the Air Cleaner 5. Wipe up any excess grease. Service Interval: Before each use or daily—Check the air cleaner for dirty, loose or damaged parts. -
Page 25: Servicing The Engine Oil
Replace a dirty, bent, or damaged element. Handle new elements carefully; do not use if the rubber seal is damaged. 4. Clean all air cleaner components of any accumulated dirt or foreign material. Prevent any dirt from entering the carburetor. 5. - Page 26 2. Park the machine so that the drain side is slightly lower than the opposite side to assure the oil drains completely. 3. Disengage the blade control switch and move the motion controls outward to the park position. 4. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
-
Page 27: Servicing The Spark Plug
G005177 G005070 Figure 30 Figure 31 3. Adapter 1. Oil filter 1. Spark plug and wire location 2. Gasket 15. Slowly pour approximately 80% of the specified oil Checking the Spark Plug into the filler tube (Figure 27). 1. Look at the center of the spark plug (Figure 32). 16. -
Page 28: Fuel System Maintenance
Fuel System Annually or every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the Maintenance blower housing and any other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled. Torque the blower housing screws to 5.5 ft-lb (7.5 N-m). -
Page 29: Electrical System Maintenance
Electrical System Maintenance Charging the Battery Removing the Battery Battery terminals or metal tools could short G005071 against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • When removing or installing the battery, do Figure 33 not allow the battery terminals to touch any 1. -
Page 30: Installing The Battery
5. Slide the rubber cover up the positive (red) cable. Disconnect the positive (red) cable from the battery post (Figure 34). Retain all fasteners. 6. Remove the battery hold-down (Figure 34) and lift the battery from the battery tray. Figure 35 1. -
Page 31: Drive System Maintenance
Drive System Maintenance Checking the Tire Pressure Service Interval: Every 25 hours—Check tire pressure. Maintain the air pressure in the front and rear tires as G005073 specified. Uneven tire pressure can cause uneven cut. Check the pressure at the valve stem (Figure 37). Check the tires when they are cold to get the most accurate pressure reading. -
Page 32: Mower Maintenance
File down any nicks and sharpen the Checking for Bent Blades blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement 1. Raise the height-of-cut lever to the transport blade. For convenient sharpening and replacement, you position, cutting height position G (also the may want to keep extra blades on hand. -
Page 33: Leveling The Mower From Side-To-Side
The blades must be replaced if a solid object is hit, if the blade is out of balance, or the blade is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other Figure 42 manufacturers may result in non-conformance with 1. -
Page 34: Adjusting The Front-To-Rear Blade Slope
5. Carefully rotate the blade(s) side to side (Figure 43). If both measurements are not within 3/16 inch (5 mm), an adjustment is required; continue with this procedure. G005278 Figure 43 G005074 1. Blades side to side 3. Outside cutting edges 2. -
Page 35: Removing The Mower
6. Measure from the tip of the front blade to the flat is 1/16-5/16 inch (1.6-7.9 mm) lower than the rear surface and the tip of the rear blade to the flat blade tip (Figure 45). surface (Figure 45). If the front blade tip is not 10. -
Page 36: Mower Belt Maintenance
The spring is under tension when installed and can cause personal injury. Be careful when removing the belt. G005077 Figure 48 1. Mower deck 3. Rear lift rod 2. Hanger bracket G005191 6. Slide the mower deck rearward to remove the mower Figure 49 belt from the engine pulley. -
Page 37: Replacing The Grass Deflector
Replacing the Grass Deflector 6. Place the spring on the rod, with end wires down, and between the grass deflector brackets. Slide rod Service Interval: Before each use or daily—Inspect the through second grass deflector bracket (Figure 50). grass deflector for damage 7. -
Page 38: Cleaning
Cleaning Note: If the mower is not clean after one washing, soak it and let it stand for 30 minutes. Then repeat the process. Washing the Underside of the 8. Run the mower again for one to three minutes to Mower remove excess water. -
Page 39: Storage
Storage Important: Do not store stabilizer/conditioned gasoline over 30 days. Cleaning and Storage 11. Remove the spark plug(s) and check its condition; refer to Servicing the Spark Plug in the Engine 1. Disengage the blade control switch, move the Maintenance section. With the spark plug(s) motion controls outward to the park position, stop removed from the engine, pour two tablespoons of the engine, and remove the key. -
Page 40: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine overheats. 1. The engine load is excessive. 1. Reduce ground speed. 2. The oil level in the crankcase is low. 2. Add oil to the crankcase. 3. The cooling fins and air passages 3. - Page 41 Problem Possible Cause Corrective Action There is abnormal vibration. 1. The engine mounting bolts are loose. 1. Tighten the engine mounting bolts. 2. The engine pulley, idler pulley, or blade 2. Tighten the appropriate pulley. pulley is loose. 3. The engine pulley is damaged. 3.
-
Page 42: Schematics
Schematics Electrical Diagram (Rev. A) - Page 43 Spypros Stavrinides Limited Cyprus 357 22 434131 Surge Systems India Limited India 91 1 292299901 Hungary T-Markt Logistics Ltd 36 26 525 500 Toro Australia Australia 61 3 9580 7355 Toro Europe BVBA 32 14 562 960 Belgium 374-0102 Rev A...
- Page 44 Instructions for Obtaining Warranty Service The Toro® Company and its afliate, Toro Warranty Company, If you think that your Toro Product contains a defect in materials pursuant to an agreement between them, jointly promises to the or workmanship, follow this procedure: original purchaser* to repair any Toro Product used for normal 1.