Toro CCR Powerlite 38172 Operator's Manual

Hide thumbs Also See for CCR Powerlite 38172:

Advertisement

CCR Powerlite® Snowthrower
Model No. 38172—Serial No. 250010001 and Up
Introduction
Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a dealer,
or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 identifies the
location of the model and serial numbers on the product.
Write the numbers in the space provided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Figure 2
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical information
and Note emphasizes general information worthy of special
attention.
© 2005—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
Important: This engine is not equipped with a
spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate
this engine on any forest-covered, brush-covered, or
grass-covered land. Other states or federal areas may
have similar laws.
This spark ignition system complies with Canadian
ICES-002
The enclosed Engine Owner's Manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty. Replacements may be ordered through
the engine manufacturer.
Safety
This snowthrower meets or exceeds the B71.3
specifications of the American National Standards
Institute in effect at the time of production.
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
Improperly using or maintaining this snowthrower
could result in injury or death. To reduce this potential,
comply with the following safety instructions.
The following instructions have been adapted from the
ANSI/OPEI standard B71.3-1995 and the ISO 8437:1989
standard.
This snowthrower is capable of amputating hands and feet
and throwing objects. Failure to observe the following
safety instructions could result in serious injury.
Register at www.Toro.com.
Form No. 3352-455 Rev A
Operator's Manual
Warning
CALIFORNIA
Proposition 65 Warning
Original Instructions (EN)
Printed in the USA
All Rights Reserved

Advertisement

Table of Contents
loading

Summary of Contents for Toro CCR Powerlite 38172

  • Page 1 Other states or federal areas may additional information, contact an Authorized Service have similar laws. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the This spark ignition system complies with Canadian location of the model and serial numbers on the product.
  • Page 2: Maintenance And Storage

    This product is intended for use only on paved surfaces. The following list contains safety information specific to • After striking a foreign object, stop the engine, remove Toro products or other safety information that you must the ignition key, thoroughly inspect the snowthrower know.
  • Page 3: Safety And Instructional Decals

    • If a shield, safety device, or decal is damaged, illegible, • or lost, repair or replace it before beginning operation. Purchase only genuine Toro replacement parts and Also, tighten any loose fasteners. accessories. • Do not smoke while handling gasoline.
  • Page 4: Loose Parts

    104–4946 Reorder Part No. 104-4938 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Step Qty. Description Oval-head bolts Curved washers Install the handle. Handle knobs Discharge chute Washers Install the discharge chute. Locknuts Knob 1.
  • Page 5: Installing The Discharge Chute

    Product Overview 2. Installing the Discharge Chute 1. Position the holes in the sides of the discharge chute over the bolts ends on the sides of the chute handle. (Figure 4). Figure 4 1. Discharge chute 3. Knob 2. Bolt ends 2.
  • Page 6: Filling The Fuel Tank

    Mixing the Gasoline and Oil This snowthrower uses a 50:1 gasoline-to-oil mixture. Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) or an equivalent high-grade, NMMA TCW-certified two-cycle oil. Important: To prevent engine damage, do not use automotive oil (such as SAE 30 or 10W30) or fuel mixed at the wrong gasoline-to-oil ratio.
  • Page 7: Adjusting The Discharge Chute

    Adjusting the Discharge Chute • Discharge the snow downwind whenever possible. • In snowy and cold conditions, some controls and To adjust the discharge chute, move the chute handle and moving parts may freeze. Do not use excessive force the chute deflector handle as shown (Figure 9). when trying to operate frozen controls.
  • Page 8: Recommended Maintenance Schedule(S)

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval After the rst operating • Check for loose fasteners and tighten them if necessary. hour • Have an Authorized Service Dealer replace the rotor blades and the scraper if necessary.
  • Page 9: Storing The Snowthrower

    1. Add a fuel stabilizer/conditioner to the fuel in the fuel discharge chute handle. tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel stabilizer/conditioner. 2. Run the engine for 5 minutes to distribute the conditioned fuel through the fuel system.
  • Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatised with your Distributor’s service or have difculty obtaining guarantee information, contact the Toro importer.

Table of Contents