Toro 73570 Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 73570
  6. Setup instructions
Toro 73570 Setup Instructions

Toro 73570 Setup Instructions

Hide thumbs Also See for 73570:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual

Loose Parts

Note: Use the chart below to identify parts for assembly.
DESCRIPTION
Rear Wheel
Wheel Bolt
R.H. Wheel Spindle
L.H. Wheel Spindle
Unplated Thrust Washer, 1.56 in. O.D x 0.06 in.
thick
Plated Wheel Washer, 1.5 in. O.D x 0.05 in.
thick
Bolt, 5/16-18 x 2.25 in.
Hex Nut, 5/16-18 in.
Spindle Cap
Front Wheel
Hubcap Washer, 2.5 in. O.D. x 0.05 in. thick
Cotter Pin, 1.5 in.
Shim Washer, 1.5 in. O.D. x 0.015 in. thick
Hubcap
Steering Wheel
Boot Washer
Nut
Lock Washer
Trim Cover
Seat Assembly
Shoulder Bolt, 5/16 in.
Locknut, 5/16 in.
Bolt, 1/4-20 x 0.88 in.
Washer, 1/4 in.
Hex Nut, 1/4-20 in.
2001 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Wheel Horse Garden Tractor
Model No. 73570–220000001 & Up
QTY.
2
10
1
1
2
4
2
2
2
2
2
2
2
2
1
1
1
1
1
1
2
2
2
2
2
1
Form No. 3325-566
520xi
Instructions
USE
Installing the rear wheels
Installing the front wheels
Installing the steering wheel
Installing the seat
Attaching the battery cables
Setup
All Rights Reserved
Printed in the USA

Advertisement

Table of Contents
loading

Related Manuals for Toro 73570

Summary of Contents for Toro 73570

  • Page 1: Loose Parts

    Form No. 3325-566 520xi Wheel Horse Garden Tractor Setup Model No. 73570–220000001 & Up Instructions Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Rear Wheel Installing the rear wheels Wheel Bolt R.H. Wheel Spindle L.H.

  • Page 2: Installing The Rear Wheels

    DESCRIPTION QTY. Grill Screw, #8 x 0.5 in. Securing the grill Grill Washer, 0.75 in. O.D. Hitch Pin Hairpin Cotter Installing the drawbar hitch pin Flat Washer, 0.50 in. I.D. Use in ignition and KeyChoice switches Installing the Rear Wheels 2.

  • Page 3: Installing The Seat

    10. Insert another 1.50 in. O.D x 0.05 in. thick plated wheel washer onto the R.H. spindle (Fig. 4). 11. Install a 2.50 in. O.D x 0.05 in thick hub cap washer onto the spindle. 12. Insert a 1.50 in. long cotter pin into the hole in the m–3451 spindle (Fig.

  • Page 4: Installing The Steering Wheel

    m–2482 Figure 7 1. Boot washer 4. Lock washer m–3453 2. Steering shaft 5. Nut 3. Steering wheel 6. Trim cover Figure 6 Checking Front Wheel Toe-In 1. Seat 5. Seat switch wire connector 2. Seat base 6. Opening for seat switch 3.

  • Page 5: Checking Tire Pressure

    3. If the stops on one side hit, and on the other side have 6. Install battery filler caps. clearance, shorten the tie rod on the side that hits, and equally lengthen the tie rod on the opposite side until both sides have clearance.

  • Page 6: Installing The Drawbar Hitch Pin

    Test Driving the Tractor 10. After servicing the battery, replace the front grill of the tractor and secure the grill with two #8 x .50” long grill screws and .75” O.D. grill washers in the upper 1. Check the oil level in the crankcase (refer to the two grill mounting holes (Fig.

Table of Contents