Sharp LC-32DH77E Service Manual page 11

5. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line
1/16 [INFO]
1 MAIN Version
2 BOOT Version
3 Monitor Version
4 T-CON/H.264 Version
5 CPLD Version
6 EQ DATA CHECKSUM
7 LAMP ERROR
8 MONITOR ERR CAUSE
9 NORMAL STANDBY CAUSE
10 ERROR STANDBY CAUSE
2/16 [INIT]
1 INDUSTRY INIT
2 INDUSTRY INIT (-Hotel)
3 HOTEL MODE
4 Center Acutime
5 RESET
6 Backlight Acutime
7 RESET
8 LAMP ERROR RESET
9 ADJ PARAM SET
10 VIC XPOS
11 VIC YPOS
12 VIC SIGNAL TYPE
13 VIC READ
3/16 [TUNER ADJ]
1 RF AGC ADJ
2 TUNER ADJ
3 PAL+TUNER ADJ
4 RF AGC ADJ (CA-8CH)
5 TUNER ADJ (CA-8CH)
6 PAL+TUNER ADJ (CA-8CH)
7 RF AGC
8 TUNER CONTRAST A_GAIN
9 TUNER CONTRAST B_GAIN
10 TUNER CONTRAST OFFSET
11 RF AGC READ
4/16 [PAL MAIN]
1 PAL ADJ
2 SECAM ADJ
3 N358 ADJ
4 PAL CONTRAST A_GAIN
5 PAL CONTRAST D_GAIN
6 PAL CONTRAST OFFSET
7 SECAM CONTRAST A_GAIN
8 SECAM CONTRAST D_GAIN
9 SECAM CONTRAST OFFSET
10 N358 CONTRAST A_GAIN
11 N358 CONTRAST D_GAIN
12 N358 CONTRAST OFFSET
5/16 [CEC TEST]
1 HDMI CEC TEST
2 INSPECT USB TERM
3 HDMI EDID WRITE
4 MONIDATA READ [TEMP/OPC]
5 CAUSE RESET
Item Description
[1] 0 0H 0M
[2] 0 0H 0M
[3] 0 0H 0M
[4] 0 0H 0M
[5] 0 0H 0M
Enter
OFF
OFF
5H 0M
OFF
19H 35M
OFF
OFF
Enter
MAIN
OFF
Enter
Enter
Enter
Enter
Enter
Enter
16
14
2048
256
OFF
Enter
Enter
Enter
14
2048
256
14
2048
256
14
2048
256
Enter
Enter
Enter
OFF
Enter
Remarks (adjustment detail, etc.)
Main software version
BOOT Version.
Monitor software version
T-CON/H.264 Version
CPLD Version.
Audio data checksum.
Number of termination due to lamp error.
Last error standby cause.
Situation that became standby at the end. (Excluding the error)
Error standby cause Total operating time before error.
Initialization to factory settings execution.
Initialization to factory settings execution. (Hotel mode is excluded)
Hotel mode ON/OFF setting
Main operating hours.
Main operating hours reset.
Backlight operating hours.
Backlight operating hours reset.
Lamp error reset.
ADJ PARAM SET
0 X-coordinate setting for VIC READ
0 Y-coordinate setting for VIC READ
Signal type setting for VIC READ
Picture level acquisition function
(Level appears in green on the upper right)
RF-AGC auto adjustment execution
TUNER auto adjustment execution
PAL TUNER auto adjustment execution
RF-AGC auto adjustment execution (CA-8CH)
TUNER auto adjustment execution (CA-8CH)
PAL TUNER auto adjustment execution (CA-8CH)
RF AGC adjustment
TUNER signal level adjustment
TUNER signal level adjustment
TUNER signal level adjustment
Reading value of RF-AGC voltage
PAL adjustment
SECAM adjustment
N358 adjustment
PAL contrast adjustment
PAL contrast adjustment
PAL contrast adjustment
SECAM contrast adjustment
SECAM contrast adjustment
SECAM contrast adjustment
N358 contrast adjustment
N358 contrast adjustment
N358 contrast adjustment
HDMI CEC test
Reading inspection of USB memory terminal
HDMI EDID WRITING
MONITOR Temperature/OPC Acquisition tool.
Reset of standby cause
3 – 3
LC-32/42/46DH77E/RU/S