Advertisement
Quick Links
MSII MSIII Window Mounting (5,000~8,000 BTU)
The unit is for window mounting only.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
NOTE:
SAVE CARTON and these INSTALLATION
INSTRUCTIONS for future reference. The carton is
the best way to store unit during winter, or when not
in use.
DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE.
FOR SAFETY REASONS, THE TOP RAIL MUST BE
SECURELY FASTENED WITH ALL FOUR (4)
SCREWS.
Some assembly is required. Please read these instructions
carefully.
Top Rail Hardware
Before installing, the top rail must be assembled on the unit.
A. Remove the air conditioner from the carton and place on a flat surface.
B. Remove top rail from the rear of the packaging material as shown in Fig. A
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
D. Secure the top rail to the unit with the 3/8 Screws as shown in Fig. C
Packaging
Installation Instructions
READ BEFORE INSTALLING UNIT
INSTALLATION WARNINGS AND CAUTION
3/8 Screw
Top Rail
Fig. A
Top Rail
Qty.
4
1
Drill (If pilot holes are needed)
Mounting Hardware
( or Wooden windows)
weather stripping
(10"X3/4"X1/12")
window sash seal foam
insulation panel
ruler
16120300A04442
Qty.
7
2
2
s)
1
5
1
2
1
1
Advertisement
Related Manuals for Frigidaire FFRE0833S1
Summary of Contents for Frigidaire FFRE0833S1
-
Page 1: Installation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT MSII MSIII Window Mounting (5,000~8,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices. - Page 2 How to Install Installation LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table.
-
Page 3: How To Install
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. - Page 4 Installation Measure the width of the inner side curtain with the provided ruler, as shown (FIG. 10). Mark a line on the patterned side of the provided insulation panel according to the measured width, then cut out the insulation panel along the line, as shown (FIG.11). Place the patterned side of the insulation panel to face inside your room, then slide the insulation panel into the frame until the panel goes into the side curtain frame completely.
- Page 5 Installation FIG. 15A & FIG. 15B). normal use, correct the slope otherwise. FIG. 15A FIG. 15B INSIDE OUTSIDE Bottom Rail Bottom Rail about Wooden Window Vinyl-Clad Window FIG. 16 In order to minimize air leaks between the room air conditioner and the window opening, suitable weather stripping(trim the provided weather stripping into suitable size) should be applied in case of any gaps found at the location as indicated by the...