Only For Training And Service Purposes - LG 32LM5800 Service Manual

- Analog (RGB) EDID table - FHD
0 1 2 3 4 5
0 00 FF FF FF FF FF FF
10 01 16 01 03 68 A0 5A
20 0F 50 54 A1 08 00 31
30 01 01 01 01 01 01 02
40 45 00 A0 5A 00 00 00
50 40 70 36 00 A0 5A 00
60 3E 1E 53 10 00 0A 20
70 00 4C 47 20 54 56 0A
CheckSum : 5C
- Analog (RGB) EDID table - HD
0 1 2 3 4 5
0 00 FF FF FF FF FF FF
10 01 15 01 03 68 10 09
20 0F 50 54 A1 08 00 81
30 01 01 01 01 01 01 1B
40 35 00 A0 5A 00 00 00
50 6E 28 55 00 A0 5A 00
60 3E 1F 46 10 00 0A 20
70 00 4C 47 20 54 56 0A
=> Detail EDID Options are below
HD( 2D TV) FHD(2D TV)
_10bit
32LS3500-DA 47LS4600-DA 32LS5600-DA
32LS3400-DA 42LS4600-DA
32CS460-DA 32LS4600-DA
42LS3400-DA
42CS560-DA
32CS560-DA
42CS460-DA
Support Deep
color
Copyright © LG Electronics. Inc. All rights reserved.

Only for training and service purposes

6 7 8 9 A B C D
00 1E 6D 01 00 01 01
78 0A EE 91 A3 54 4C
40 45 40 61 40 71 40
3A 80 18 71 38 2D 40
1E 66 21 50 B0 51 00
00 00 1E 00 00 00 FD
20 20 20 20 20 00 00
20 20 20 20 20 20 20
6 7 8 9 A B C D
00 1E 6D 01 00 01 01
78 0A EE 91 A3 54 4C
C0 61 40 45 40 31 40
21 50 A0 51 00 1E 30
1C 01 1D 00 72 51 D0
00 00 1E 00 00 00 FD
20 20 20 20 20 00 00
20 20 20 20 20 20 20
FHD(2D TV) HD (3D TV) FHD (3D TV)
_8bit
32LM3400-DA 47LM5800-DB
42LM5800-DB
32LM5800-DB
55LM4600-DB
47LM4600-DB
42LM3400-DA
Non-Support
Deep color
ASCII Code
E F
01 01
99 26
81 80
58 2C
1B 30
00 3A
00 FC
00 5C
E F
01 01
99 26
01 01
4.5. Outgoing condition Configuration
48 88
■ When pressing IN-STOP key by SVC remocon, Red LED
1E 20
are blinked alternatively. And then automatically turn off.
00 3A
(Must not AC power OFF during blinking)
00 FC
4.6 GND & Hi-pot test
00 CD
Confirm whether is normal or not when between power
board's ac block and GND is impacted on 1.5kV(dc) or
2.2kV(dc) for one second.
■ GND TEST = POWER CORD GND and SIGNAL CABLE
■ Hi-pot TEST = POWER CORD GND and LIVE&NUETRAL
■ Test Process
(1) Check the POWER CABLE and SIGNAL CABLE insertion
condition.
(2) Connect the AV JACK Tester
(3) Controller(GWS103-4) on
(4) GND TEST(Auto)
- If Test is failed, Buzzer operate
- If Test is passed, execute next process(HI-pot test)
- Remove A/V CORD from A/V JACK BOX
(5) HI-POT test(Auto)
- If Test is failed, Buzzer operate
- If Test is passed, GOOD Lamp on and move to next
process automatically.
- 17 -
GND
LGE Internal Use Only