Table of Contents
Advertisement
Quick Links
Form No. 3373-145 Rev A
SGR-6 Stump Grinder
Model No. 22610—Serial No. 311000001 and Up
Model No. 22610G—Serial No. 311000001 and Up
Model No. 32610—Serial No. 312000001 and Up
g014867
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)
Advertisement
Table of Contents
Related Manuals for Toro 22610
Summary of Contents for Toro 22610
- Page 1 Model No. 22610—Serial No. 311000001 and Up Model No. 22610G—Serial No. 311000001 and Up Model No. 32610—Serial No. 312000001 and Up g014867 To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register DANGER your product. -
Page 3: Table Of Contents
Safety Improper use or maintenance by the operator or owner Figure 2 can result in injury. To reduce the potential for injury, comply with these safety instructions and always 1. Safety alert symbol pay attention to the safety alert symbol , which means: Caution , Warning , or Danger —personal safety instruction. -
Page 4: Maintenance And Storage
Make any necessary repairs before restarting. maneuver the product. • Use only genuine Toro replacement parts to ensure that • Before grinding, have the area marked for underground original standards are maintained. -
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117–4979 1. Entanglement hazard, belt—stay away from moving parts, keep all guards and shields in place. -
Page 6: Product Overview
Product Overview g014871 Figure 4 1. Handle Release Knob Fold the handle down toward the machine and screw the knob back onto the handle(Figure 5). g014869 Figure 3 1. Handle 8. Starter 2. Throttle lever 9. Cutting wheel 3. Handle release knob 10. -
Page 7: Specifications
A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. g014872 Figure 7 1. -
Page 8: Operation
Operation DANGER In certain conditions, gasoline is extremely Note: Determine the left and right sides of the machine flammable and highly explosive. A fire or explosion from the normal operating position. from gasoline can burn you and others and can damage property. -
Page 9: Checking The Engine Oil Level
because the fuel system could be damaged. Do not mix 6. Wipe up any gasoline that may have spilled. oil with gasoline. Checking the Engine Oil Level Using Stabilizer/Conditioner Service Interval: Before each use or daily Use a fuel stabilizer/conditioner in the machine to provide 1. -
Page 10: Starting And Stopping The Engine
Starting and Stopping the Grinding a Stump Engine Place the machine into position with the cutting wheel near the front-top edge of the stump. Starting the Engine DANGER 1. Move the fuel valve to the Open position, all the way The machine will cut and amputate hands and feet. - Page 11 DANGER A rotating cutting wheel is very dangerous and can cut and amputate hands and feet. Stay at the operating position and be sure that the cutting wheel has come to a complete stop before doing anything else. g014502 Figure 12 8.
-
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important: The machine may be tipped backward or on its side to facilitate access for cleaning or service, but no longer than 2 minutes. If the machine is held in this position for too long, the engine can be damaged by gasoline draining into the crankcase. -
Page 13: Engine Maintenance
Engine Maintenance Important: Pump grease in slowly and carefully to prevent damage to the bearing seals. Servicing the Air Cleaner Service Interval: Before each use or daily The cyclone air filter collects the largest contaminant particles, which collect in the container. When you can see a layer of dirt at the bottom of the container, clean the cyclone housing, air channels, and air intake screen. -
Page 14: Servicing The Engine Oil
Oil Type: Detergent oil with an API service of SJ or higher. Crankcase Capacity: .63 qt (.6 liters) Viscosity: SAE 10W-30 is recommended for general use. Changing the Engine Oil Service Interval: After the first 25 hours Every 100 hours Yearly or before storage 1. -
Page 15: Servicing The Spark Plug
Underneath the fuel valve is a sediment cup to catch dirt in the fuel. 1. Move the fuel valve to the Off position, all the way to the left. 2. Unscrew the sediment cup. Make sure not to misplace the o-ring (Figure 17). Figure 18 1. -
Page 16: Belt Maintenance
Belt Maintenance Checking the Drive Belt Tension Service Interval: Every 25 hours Note: Replace the belt if it shows any signs of wear, cracks, or damage. 1. Shut off the engine and wait for all rotating parts to stop. 2. Remove belt guard retaining screws (Figure 20). Figure 21 1. -
Page 17: Grinder Maintenance
Grinder Maintenance Checking the Cutting Wheel Blades Service Interval: Before each use or daily Among the most critical elements of the machine is the cutting wheel blades. They are also the most subject to damage and wear. In the course of grinding stumps they not only make contact with the wood, but they also encounter numerous abrasives and objects, such as dirt, stones, and occasionally a large rock or buried scrap. -
Page 18: Cleaning
Cleaning Storage For storage over 30 days, prepare the unit as follows: Removing Debris from the 1. Remove dirt and grime from the external parts of Machine the entire unit, especially the engine. Clean dirt and sawdust chips from the outside of the engine cylinder Regular cleaning and washing will increase the life span of head fins and blower housing. -
Page 19: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine will not start. 1. The engine switch is in the Off position. 1. Hold the safety bail against the handle. 2. The fuel shutoff valve is closed. 2. Open the fuel valve. 3. - Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.