Page 2
EAU26943 DECLARATION of CONFORMITY Company: MORIC CO., LTD. Address: 1450-6 Mori Mori-Machi Shuchi-gun Shizuoka 437-0292 Japan Hereby declare that the product: Kind of equipment: IMMOBILIZER Type-designation: 5SL-00 is in compliance with following norm(s) or documents: R&TTE Directive(1999/5/EC) EN300 330-2 v1.1.1(2001-6), EN60950-1(2001) Two or Three-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC) Place of issue: Shizuoka, Japan Date of issue: 1 Aug.
Page 3
Yamaha a reputation for dependability. Please take the time to read this manual thoroughly, so as to enjoy all advantages of your FJR1300AS. The owner’s manual does not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourself and others from trouble and injury.
This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual.
TABLE OF CONTENTS SAFETY INFORMATION ....1-1 Accessory box ......3-26 Removing and installing panels ..6-6 Adjusting the headlight beams ..3-26 Checking the spark plugs ....6-8 DESCRIPTION ........2-1 Handlebar position ....... 3-27 Engine oil and oil filter cartridge ..6-9 Left view ..........2-1 Opening and closing the Final gear oil ........
Page 7
TABLE OF CONTENTS Lubricating the swingarm pivots ...6-24 Lubricating the rear suspension ...6-24 Checking the front fork ....6-24 Checking the steering ....6-25 Checking the wheel bearings ..6-26 Battery ..........6-26 Replacing the fuses ......6-27 Headlight bulb ......6-29 Front turn signal light ....6-29 Replacing a rear turn signal light bulb or a tail/brake light bulb ..6-29 Replacing the license plate...
SAFETY INFORMATION EAU10281 AND/OR WHEN MADE NECES- • Ride where other motorists can SARY BY MECHANICAL CONDI- see you. Avoid riding in another MOTORCYCLES SINGLE TIONS. motorist’s blind spot. TRACK VEHICLES. THEIR SAFE USE Many accidents involve inexperi- AND OPERATION ARE DEPENDENT Safe riding enced operators.
Page 9
Modifications made to this motorcycle other motorists can see you. the single most critical factor in the pre- not approved by Yamaha, or the re- The posture of the operator and vention or reduction of head injuries. moval of original equipment, may ren- passenger is important for proper Always wear an approved helmet.
Page 10
Maximum load: been specifically designed for use on create instability due to improper 208 kg (459 lb) this motorcycle. Since Yamaha cannot weight distribution or aerody- test all other accessories that may be namic changes. If accessories When loading within this weight limit,...
Page 11
SAFETY INFORMATION tor and may limit control ability, Always turn the engine off before or clothing, immediately wash the therefore, such accessories are leaving the motorcycle unattended affected area with soap and water not recommended. and remove the key from the main and change your clothes.
Immobilizer system This is not an automatic transmission, This vehicle features the YCC-S only the clutch system is automatic. (Yamaha Chip Controlled-Shift) sys- The gears must be shifted by the rider. tem. The basic function of this system allows the rider to shift gears without the use of a clutch lever.
Page 16
Do not expose any key to exces- a Yamaha dealer to have them re-reg- sively high temperatures. istered. Do not use the key with the red Do not place any key close to bow for driving.
INSTRUMENT AND CONTROL FUNCTIONS EAU10471 EAU26811 To lock the steering Main switch/steering lock All electrical circuits are supplied with power; the meter lighting, taillights, li- cense plate light and auxiliary lights come on, and the engine can be start- ed. The key cannot be removed. NOTE: The headlights come on automatically when the engine is started and stay on...
INSTRUMENT AND CONTROL FUNCTIONS To unlock the steering EAU39460 EAU11003 (Parking) Indicator and warning lights The steering is locked, and the tail- lights, license plate light and auxiliary lights are on. The hazard lights and turn signal lights can be turned on, but all other electrical systems are off.
Page 19
Stop the vehicle when it is safe to do so, Even if the oil level is sufficient, the have a Yamaha dealer check the self- and park it away from traffic. Have a warning light may flicker when riding on diagnosis system.
Page 20
ABS may be defective. Yamaha dealer check the electrical cir- then while rotating the rear wheel, push If this occurs, have a Yamaha dealer cuit. the shift pedal rod and pivot forward un- til the transmission is in the neutral po- check the system as soon as possible.
INSTRUMENT AND CONTROL FUNCTIONS EAU11601 EAU11872 EAU40532 Speedometer Tachometer Multi-function display 1. Tachometer 1. Tachometer 1. Multi-function display 2. Speedometer 2. Tachometer red zone 2. “SELECT” button 3. Multi-function display 3. “RESET” button The electric tachometer allows the rider The speedometer shows the riding EWA14430 to monitor the engine speed and keep it WARNING...
Page 22
INSTRUMENT AND CONTROL FUNCTIONS a fuel reserve tripmeter (which Odometer and tripmeter modes distance traveled from that point. In that shows the distance traveled on the case, pushing the “SELECT” button fuel reserve) switches the display between the vari- a clock ous tripmeter and odometer modes in a fuel meter the following order:...
Page 23
INSTRUMENT AND CONTROL FUNCTIONS Clock Fuel meter will start flashing. If this occurs, have a Yamaha dealer check the electrical cir- cuit. Coolant temperature meter 1. Clock 1. Fuel meter 2. “SELECT” button The fuel meter indicates the amount of 3.
Page 24
INSTRUMENT AND CONTROL FUNCTIONS ECA10020 Ambient temperature, instanta- Ambient temperature mode CAUTION: neous fuel consumption and aver- fuel consumption modes Do not operate the engine if it is (except for the UK) overheated. Transmission gear display 1. Ambient temperature This display shows the ambient tem- perature from –9 °C to 50 °C in 1 °C in- 1.
Page 25
INSTRUMENT AND CONTROL FUNCTIONS The accuracy of the temperature When the display is set to “L/100 The average fuel consumption display reading may be affected when km”, the amount of fuel necessary can be set to either “AV_ _._ km/L” or riding slowly (approximately under to travel 100 km under the current “AV_ _._ L/100 km”.
Page 26
50 °C will not be displayed. If there is a malfunction, “– –.–” will Air → MPG → AV_ _._ MPG → Air The accuracy of the temperature be displayed. Have a Yamaha dealer reading may be affected when check the vehicle. Ambient temperature mode riding slowly [approximately under 20 km/h (12.5 mi/h)] or when...
Page 27
When the average fuel consumption such an error code, note the code num- mode is selected, the display flashes ber, and then have a Yamaha dealer for five seconds, and then “AV_ _._ check the vehicle. MPG” (average distance that can be traveled using 1.0 Imp.gal of fuel) is dis-...
If the multi-function display indicates two-digit error code when the key is any error codes, note the code number, turned to “ON”. and then have a Yamaha dealer check the vehicle. NOTE: If the multi-function display indicates er- ror code 52, this could be caused by transponder interference.
INSTRUMENT AND CONTROL FUNCTIONS EAU12347 Right position. To cancel the turn signal Handlebar switches lights, push the switch in after it has re- turned to the center position. Left EAU12493 Windshield position adjusting switch “ ” To move the windshield up, push this switch in direction (a).
Page 30
INSTRUMENT AND CONTROL FUNCTIONS EAU12500 EAU12733 EAU40381 Horn switch “ ” Hazard switch “ ” Hand shift control switch Press this switch to sound the horn. With the key in the “ON” or “ ” posi- tion, use this switch to turn on the haz- EAU12660 ard lights (simultaneous flashing of all Engine stop switch “...
INSTRUMENT AND CONTROL FUNCTIONS and release this switch after start- EAU40492 Shift pedal ing the engine to enable hand shifting. 1. Shift pedal 2. Bolt 1. Shift pedal 3. Standard position This vehicle is equipped with a con- 2. Move the shift pedal to the desired stant-mesh 5-speed transmission.
INSTRUMENT AND CONTROL FUNCTIONS EAU40481 EAU26822 EAU39540 Hand shift lever “ ”/“ ” Brake lever Brake pedal The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. 1.
This ABS has a test mode which EAU13072 Fuel tank cap allows the owner to experience the The Yamaha ABS (Anti-lock Brake pulsating at the brake lever or System) features a dual electronic con- brake pedal when the ABS is oper- trol system, which acts on the front and ating.
Avoid spilling fuel on the hot en- Your Yamaha engine has been de- gine. signed to use regular unleaded gaso- line with a research octane number of 91 or higher.
INSTRUMENT AND CONTROL FUNCTIONS or premium unleaded fuel. Use of un- EAU39450 EAU13441 Fuel tank breather/overflow Catalytic converter leaded fuel will extend spark plug life hose This vehicle is equipped with catalytic and reduce maintenance costs. converters in the exhaust system. EWA10860 WARNING The exhaust system is hot after op-...
INSTRUMENT AND CONTROL FUNCTIONS EAU39491 Seats Passenger seat To remove the passenger seat 1. Insert the key into the seat lock, and then turn it counterclockwise. 1. Projection 1. Rider seat lock lever 2. Seat holder 2. Rider seat 2. Remove the key. To install the rider seat 1.
INSTRUMENT AND CONTROL FUNCTIONS 2. Install the passenger seat. EAU39632 Adjusting the rider seat height NOTE: The rider seat height can be adjusted to Make sure that the seats are prop- one of two positions to suit the rider’s erly secured before riding. preference.
Page 38
INSTRUMENT AND CONTROL FUNCTIONS 6. Align the projection on the bottom of the rider seat with the “H” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 1. Rider seat height position adjuster 1.
208 kg (459 lb) for the ve- tion slot, and then push the rear of hicle. the seat down to lock it in place as shown. 1. Storage compartment 2. Yamaha CYCLELOK (optional) This storage compartment is designed 1. “L” position slot hold genuine Yamaha CYCLELOK.
INSTRUMENT AND CONTROL FUNCTIONS EAU39480 ECA11800 EAU39610 Accessory box Adjusting the headlight CAUTION: The accessory box is located beside beams Do not place heat-sensitive items in the meter panel. The headlight adjusting knobs are used the accessory box. The accessory to raise or lower the height of the head- box gets extremely hot especially To open the accessory box...
The handlebars can be adjusted to one ings of three positions to suit the rider’s pref- The cowlings can be tilted back 30 mm erence. Have a Yamaha dealer adjust (1.18 in) for added ventilation to suit the the position of the handlebars. riding conditions.
INSTRUMENT AND CONTROL FUNCTIONS EAU39671 EAU14731 Rear view mirrors Adjusting the front fork The rear view mirrors of this vehicle can This front fork is equipped with spring be folded forward or backward for park- preload adjusting bolts, rebound damp- ing in narrow spaces.
Page 43
INSTRUMENT AND CONTROL FUNCTIONS load thereby soften Rebound damping force Compression damping force suspension, turn the adjusting bolt on each fork leg in direction (b). NOTE: Align the appropriate groove on the ad- justing mechanism with the top of the front fork cap bolt.
INSTRUMENT AND CONTROL FUNCTIONS ECA10100 EAU14911 For riding solo, move the spring preload Adjusting the shock absorber CAUTION: adjusting lever in direction (b). For assembly riding with a passenger, move the Never attempt to turn an adjusting This shock absorber assembly is spring preload adjusting lever in direc- mechanism beyond the maximum or equipped with a spring preload adjust-...
Standard: formance. the engine is running. 12 click(s) in direction (b)* Always have a Yamaha dealer Maximum (hard): Use the grip warmer adjusting knob, lo- service the shock absorber. 3 click(s) in direction (b)*...
INSTRUMENT AND CONTROL FUNCTIONS EAU15301 below and have a Yamaha dealer re- NOTE: Sidestand pair it if it does not function proper- When the vehicle is stopped or travel- The sidestand is located on the left side ing at extremely low speeds (e.g., in of the frame.
Periodically check the operation of the ignition circuit cut-off system according to the following procedure. EWA10260 WARNING The vehicle must be placed on the centerstand during this in- spection. If a malfunction is noted, have a Yamaha dealer check the sys- tem before riding. 3-33...
Page 48
The vehicle should not be ridden until With the engine still running: checked by a Yamaha dealer. 7. Move the sidestand up. 8. Keep the front or rear brake applied. 9. Shift the transmission into gear.
INSTRUMENT AND CONTROL FUNCTIONS EAU39651 EWA14360 Auxiliary DC jack WARNING This vehicle is equipped with an auxilia- To prevent electrical shock or short- ry DC jack in the accessory box. circuiting, make sure that the cap is A 12-V accessory connected to the installed when the auxiliary DC jack auxiliary jack can be used when the key is not being used.
PRE-OPERATION CHECKS EAU15592 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
• If necessary, add recommended coolant to specified level. 6-13 • Check cooling system for leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check brake pads for wear. Front brake • Replace if necessary.
Page 52
• Make sure that operation is smooth. • Check cable free play. Throttle grip 6-15, 6-22 • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. • Make sure that operation is smooth. Control cables 6-22 •...
OPERATION AND IMPORTANT RIDING POINTS EAU40572 The gears can be shifted using either NOTE: Shifting the shift pedal or the hand shift lever. If the engine fails to start, release the The hand shift lever has to be enabled start switch, wait a few seconds, and by pressing the hand shift control then try again.
OPERATION AND IMPORTANT RIDING POINTS Always return the throttle to the EAU16810 EAU16841 Tips for reducing fuel con- Engine break-in closed position while changing sumption There is never a more important period gears to avoid damaging the en- in the life of your engine than the period Fuel consumption depends largely on gine, transmission, and drive between 0 and 1600 km (1000 mi).
If you are not familiar with mainte- certain maintenance work correctly. nance work, have a Yamaha dealer do it for you. NOTE: If you do not have the tools or experi- ence required for a particular job, have a Yamaha dealer perform it for you.
The annual checks must be performed every year, except if a kilometer-based maintenance is performed in- stead. From 50000 km, repeat the maintenance intervals starting from 10000 km. Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills. ODOMETER READING (× 1000 km)
Page 59
PERIODIC MAINTENANCE AND MINOR REPAIR ODOMETER READING (× 1000 km) ANNUAL ITEM CHECK OR MAINTENANCE JOB CHECK √ √ √ √ 9 * Wheels • Check runout and for damage. • Check tread depth and for damage. • Replace if necessary. √...
Page 60
PERIODIC MAINTENANCE AND MINOR REPAIR ODOMETER READING (× 1000 km) ANNUAL ITEM CHECK OR MAINTENANCE JOB CHECK • Change. √ √ √ √ √ √ Engine oil • Check oil level and vehicle for oil leakage. Engine oil filter car- √...
Page 61
PERIODIC MAINTENANCE AND MINOR REPAIR Hydraulic brake and YCC-S clutch service • Regularly check and, if necessary, correct the brake and YCC-S clutch fluid levels. • Every two years replace the internal components of the brake master cylinders and calipers as well as YCC-S clutch master and release cylinders, and change the brake and YCC-S clutch fluids.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU18771 Removing and installing pan- The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. 1.
Page 63
PERIODIC MAINTENANCE AND MINOR REPAIR EAU39601 Panel C To remove the panel 1. Remove the seats. (See page 3-22.) 2. Remove the bolt and the quick fas- tener screws, and then take the panel off. 1. Panel B 2. Install the seats. 2.
Do not attempt to diagnose 0.7–0.8 mm (0.028–0.031 in) such problems yourself. Instead, have a Yamaha dealer check the vehicle. Clean the surface of the spark plug If a spark plug shows signs of electrode gasket and its mating surface, and then...
PERIODIC MAINTENANCE AND MINOR REPAIR EAU19881 2. Place an oil pan under the engine Engine oil and oil filter car- NOTE: to collect the used oil. The engine oil should be between the tridge 3. Remove the engine oil filler cap minimum and maximum level marks.
Page 66
An oil filter wrench is available at a seated. 43 Nm (4.3 m·kgf, 31 ft·lbf) Yamaha dealer. 6. Install the new oil filter cartridge, 8. Add the specified amount of the 5. Apply a thin coat of engine oil to...
If any page (since the engine oil also or remains on, immediately turn the leakage is found, have a Yamaha deal- lubricates the clutch), do not engine off and have a Yamaha dealer er check and repair the vehicle. In addi- mix any chemical additives.
Page 68
PERIODIC MAINTENANCE AND MINOR REPAIR 2. Remove the oil filler bolt, and then Tightening torque: Tightening torque: check the oil level in the final gear Final gear oil filler bolt: Final gear oil filler bolt: case. 23 Nm (2.3 m·kgf, 17 ft·lbf) 23 Nm (2.3 m·kgf, 17 ft·lbf) NOTE: 6.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU20070 Coolant NOTE: The coolant should be between the The coolant level should be checked minimum and maximum level marks. before each ride. In addition, the cool- ant must be changed at the intervals specified in the periodic maintenance and lubrication chart.
Yamaha dealer change the coolant. in the periodic maintenance and lubri- coolant, have a Yamaha dealer cation chart. Have a Yamaha dealer check the antifreeze content of clean and replace the air filter element. the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced.
To prevent this checked as follows and, if necessary, from occurring, the valve clearance adjusted by a Yamaha dealer at the in- must be adjusted by a Yamaha dealer tervals specified in the periodic mainte- at the intervals specified in the periodic nance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU21771 NEVER OVERLOAD Tire air pressure (measured on cold Tires MOTORCYCLE! Operation of an tires): To maximize the performance, durabil- overloaded motorcycle may re- 0–90 kg (0–198 lb): ity, and safe operation of your motor- Front: sult in tire damage, loss of con- cycle,...
Page 73
Tire information glass fragments in it, or if the sidewall is Use only the tire valves and cracked, have a Yamaha dealer re- valve cores listed below to place the tire immediately. avoid tire deflation during a high-speed ride.
Always adjust the tire air pres- 180/55 ZR17M/C (73W) fore each ride. If any damage is Manufacturer/model: sure according to the operating found, have a Yamaha dealer re- METZELER/Roadtec Z6C conditions. BRIDGESTONE/BT020R place the wheel. Do not attempt FRONT and REAR:...
If ified in the periodic maintenance and before each ride. If the YCC-S clutch necessary, have a Yamaha dealer ad- lubrication chart. plates wear out, shifting becomes just the brake light switch.
PERIODIC MAINTENANCE AND MINOR REPAIR cator groove has almost disappeared, EAU40591 YCC-S clutch Checking the brake and have a Yamaha dealer replace the YCC-S clutch fluid levels brake pads as a set. Front brake EAU22500 Rear brake pads 1. Minimum level mark...
YCC-S clutch fluids 6-6.) stalling them. Have a Yamaha dealer change the Be careful that water or dust does Observe these precautions: brake and YCC-S clutch fluids at the in- not enter the brake and YCC-S...
If a cable is damaged maintenance chart. or does not move smoothly, have a Yamaha dealer check or replace it. Recommended lubricant: Engine oil EWA10720 WARNING...
Recommended lubricant: EWA10740 Lithium-soap-based grease (all-pur- WARNING pose grease) If the centerstand or sidestand does not move up and down smoothly, have a Yamaha dealer check or re- pair it. Recommended lubricant: Lithium-soap-based grease (all-pur- pose grease) 6-23...
PERIODIC MAINTENANCE AND MINOR REPAIR EAUM1650 EAU23250 EAU23271 Lubricating the swingarm piv- Lubricating the rear suspen- Checking the front fork sion The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic main- tenance and lubrication chart.
Securely support the vehicle so that fork does not operate smoothly, there is no danger of it falling over. have a Yamaha dealer check or re- pair it. 2. Hold the lower ends of the front fork legs and try to move them for- ward and backward.
Batteries produce explosive hy- To charge the battery drogen gas. Therefore, keep Have a Yamaha dealer charge the bat- sparks, flames, cigarettes, etc., tery as soon as possible if it seems to away from the battery and pro- have discharged.
The main fuse, the fuse boxes and the CHILDREN. sealed-type (MF) battery charg- ABS motor fuse are located under pan- er, have a Yamaha dealer el A. (See page 6-6.) charge your battery. To store the battery 1. If the vehicle will not be used for...
Page 84
2. Right radiator fan fuse 10.0 A 4. If the fuse immediately blows Hazard fuse: 3. Left radiator fan fuse again, have a Yamaha dealer 10.0 A 4. Hazard fuse check the electrical system. Fuel injection system fuse: 5. Backup fuse (for odometer, clock and immo- 15.0 A...
If a front turn signal light does not come light bulb or a tail/brake light Yamaha dealer check its electrical cir- on, have a Yamaha dealer check its bulb cuit or replace the bulb. electrical circuit or replace the bulb.
PERIODIC MAINTENANCE AND MINOR REPAIR 6. Install the passenger seat. EAU24310 3. Remove the defective bulb by pull- Replacing the license plate ing it out. light bulb 4. Insert a new bulb into the socket. 1. Remove the license plate light unit 5.
The following troubleshooting charts represent quick and easy procedures for checking these vital systems your- self. However, should your motorcycle require any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, experience, and know-how to service the motorcycle properly.
Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
Page 89
Start the engine. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. is OK. NOTE: If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
Rust and corrosion can develop matte colored finished parts. Be ECA10770 even if high-quality components are sure to consult a Yamaha dealer for CAUTION: advice on what products to use be- used. A rusty exhaust pipe may go un- Avoid using strong acidic wheel fore cleaning the vehicle.
Page 91
MOTORCYCLE CARE AND STORAGE thinner, fuel (gasoline), rust re- After normal use ECA10790 CAUTION: movers or inhibitors, brake flu- Remove dirt with warm water, a mild id, antifreeze or electrolyte. detergent, and a soft, clean sponge, Do not use warm water since it in- Do not use high-pressure wash- and then rinse thoroughly with clean creases the corrosive action of the...
7. Let the motorcycle dry completely Always store your motorcycle in a cool, NOTE: before storing or covering it. dry place and, if necessary, protect it Consult a Yamaha dealer for advice on EWA11130 against dust with a porous cover. WARNING what products to use.
Page 93
MOTORCYCLE CARE AND STORAGE 3. Perform the following steps to pro- 4. Lubricate all control cables and the tect the cylinders, piston rings, etc. pivoting points of all levers and from corrosion. pedals as well as of the side- a. Remove the spark plug caps stand/centerstand.
SPECIFICATIONS Dimensions: Engine oil: Fuel injector: Overall length: Type: Manufacturer: 2230 mm (87.8 in) SAE20W40 NIPPON INJECTOR Overall width: Recommended engine oil grade: Model/quantity: 750 mm (29.5 in) API service SG type or higher, JASO INP-151/4 Overall height: standard MA Spark plug (s): 1450 mm (57.1 in) Engine oil quantity:...
Page 95
SPECIFICATIONS 3rd: (Total weight of rider, passenger, cargo and Operation: 31/23 (1.348) accessories) Right hand operation 4th: Tire air pressure (measured on cold Recommended fluid: 28/26 (1.077) DOT 4 tires): 5th: Rear brake: Loading condition: 26/28 (0.929) Type: 0–90 kg (0–198 lb) Chassis: Single disc brake Front:...
Page 96
SPECIFICATIONS Voltage, capacity: Fuses: 12 V, 12.0 Ah Main fuse: Headlight: 50.0 A Bulb type: Headlight fuse: Halogen bulb 25.0 A Bulb voltage, wattage × quantity: Signaling system fuse: 15.0 A Headlight: 12 V, 60 W/55.0 W × 2 Ignition fuse: 10.0 A Tail/brake light: 12 V, 5.0 W/21.0 W ×...
Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
Page 98
The model label is affixed to the frame under the passenger seat. (See page 3-22.) Record the information on this la- bel in the space provided. This informa- tion will be needed when ordering spare parts from a Yamaha dealer.
Page 99
INDEX Engine trouble/YCC-S indicators and warning light..........3-5 ABS ............3-19 License plate light bulb, replacing..6-30 ABS warning light ........3-6 Accessory box ........3-26 Final gear oil..........6-11 Main switch/steering lock......3-3 Air filter element........6-14 Front and rear brake pads, checking ..6-19 Matte color, caution ........