Miele PT 8301 SL Operating Instructions Manual
Hide thumbs
Also See for PT 8301 SL:
- Operating instructions manual (44 pages) ,
- Short operating instructions (2 pages)
Table of Contents
Related Manuals for Miele PT 8301 SL
Summary of Contents for Miele PT 8301 SL
-
Page 1: Operating Instructions
Operating instructions Dryers PT 8301 SL PT 8303 SL en - AU, NZ To avoid the risk of accidents or damage to the machine, it is essential to read these instructions before installing, M.-Nr. 09 197 130 commissioning and using it for the first time. - Page 3 Gas-heated machines Safety precautions to take if you smell gas – Turn off the gas emergency control valve immediately. This is usually located near the gas meter. – Do not enter a room with an open flame where there is a smell of gas. –...
-
Page 4: Table Of Contents
Contents Warning and Safety instructions ............. . . 5 Caring for the environment . -
Page 5: Warning And Safety Instructions
Warning and Safety instructions THIS APPLIANCE SHALL NOT BE USESD TO DRY OFF SOLVENTS OR DRY CLEANING FLUIDS. Explanation of the Warning and Safety To prevent the risk of fire, the following must symbols on the machine not be dried in this tumble dryer (with the exception of those fabrics which can be dried in the Special It is essential to read these operating Programmes specifically designed for them):... - Page 6 Faulty components must only be replaced by Whilst the dryer is in use, the porthole glass and genuine Miele original spare parts. Only when these drum door frame can become very hot. Laundry will parts are fitted can the safety standards of the also be very hot if you remove it early.
- Page 7 The machine should be tested with the burner switched on and switched off. Using accessories Accessory parts may only be fitted when expressly approved by Miele. If spare parts or accessories from other manufacturers are used, this will invalidate the warranty, and Miele cannot accept liability.
-
Page 8: Caring For The Environment
Caring for the environment Disposal of the packing material Tips on saving energy The transport and protective packing has been Make sure that your laundry is thoroughly spun selected from materials which are environmentally before drying. This saves time and energy. friendly for disposal. -
Page 9: Guide To The Machine
Guide to the machine a Control panel f Gas connection b Drum door g Gas heating indicator light Pull the door handle to open the drum door. This comes on when the heating is in operation. c Access to fluff filter h Air intake The fluff filter is opened with a key. -
Page 10: Description Of Tumble Dryer Pt 8301
Description of tumble dryer PT 8301 Control panel PT 8301 Profitronic B Timed programmes 1 Segment display - Time 2 Programme sequence display 3 Temperature selection button 4 Venting system fault indicator 5 Fluff filter fault indicator 6 START/STOP button 7 Time selection rotary dial 8 On/Off switch Mains On/Off switch s... -
Page 11: Description Of Tumble Dryer Pt 8303
Description of tumble dryer PT 8303 Control panel PT 8303 Profitronic B Plus Residual moisture programmes 1 Segment display - Residual moisture 2 Programme sequence display 3 Low temperature (additional option) button 4 Venting system fault indicator 5 Fluff filter fault indicator 6 START/STOP button 7 Programme selection rotary control 8 On/Off switch... -
Page 12: Drying
Drying Sort the laundry This can cause the drying process to go on for too long, or to not finish at all. Open zips before drying. Not all textiles are suitable for machine drying. Loopknit and woven textiles (e.g. T-shirts and Please read the instructions given on the garment underwear) have a tendency to shrink depending on their quality. -
Page 13: Before Using For The First Time
Drying This machine must only be installed and commissioned by a Miele authorised technician. Before using for the first time Before loading the dryer with laundry, wipe the internal drum surface with a soft, dry cloth. Switching the dryer on and loading the... -
Page 14: Dryer Pt 8301
Dryer PT 8301 Selecting a temperature Drying High Cooling down Medium Programme finished / Anti-crease The programme sequence is displayed in three Cold stages. The stage the programme is at will be highlighted in yellow. At the end of the programme ^ Press the temperature selection button and select At the end of the programme a buzzer will sound to the required drying temperature - Cold, Low,... -
Page 15: Dryer Pt 8303
Dryer PT 8303 Selecting a programme Lowering the temperature ^ When drying delicate fabric (such as acrylic), press the K Low temperature additional option button. ^ Press the START/STOP button. The drying programme will begin. The segment display will show the residual moisture which is currently in the laundry until the programme is finished. -
Page 16: After Drying
After drying At the end of the programme To continue the drying programme: ^ Open the drum door. ^ Close the drum door. The remaining drying duration or the target residual If the door remains closed, the dryer will start up moisture level will flash in the segment display. -
Page 17: Pt 8301 Cop
PT 8301 COP Control panel PT 8301 Profitronic B COP (Coin Operation) 1 Segment display - Time 2 Programme sequence display 3 Temperature selection button 4 Venting system fault indicator 5 Fluff filter fault indicator 6 START/STOP button 7 On/Off switch Time selection can be controlled by a C 4065 or C 4070 coin control unit or other type of payment system. -
Page 18: Reprogramming
Reprogramming Reprogramming individual drying Example of reprogramming PT 8301 Profitronic B Timed programme machines programmes (Changing the Standard options) P 4 to alter the acoustic tone when a button is Individual drying programmes can be altered to suit pressed (see "Programmable functions"). specific requirements, practices and processes. -
Page 19: Programmable Functions
Reprogramming Programmable functions Programmable function Standard Programmable option Buzzer volume 0 = quiet 1 = loud Buzzer at the end of the programme 0 = Off 1 = On Memory function 0 = Off 1 = On Acoustic tone which sounds when a button is pressed 0 = Off 1 = On P 5*... -
Page 20: Problem Solving Guide
(cold) for the remainder of the programme. In the event of any of the following faults, please contact the Miele Professional Service Department: – excessive noise – there is a gaseous or burning odour –... -
Page 21: Cleaning And Care
The following should be checked and cleaned once a year by a Miele authorised service technician: – The burners and burner compartment on gas-heated dryers, the heaters and heater shaft on electric-heated dryers. -
Page 22: Installation And Connection
To ensure suitable access for future maintenance and This dryer must only be installed and service work, please ensure that the minimum commissioned by a Miele authorised technician. distances between the dryer and the wall specified on the installation diagram are strictly observed. -
Page 23: Levelling The Appliance
This dryer is fitted with an exhaust fan which can be heard during operation. If this noise disturbs you, it is possible to fit a silencer Gas-heated dryers must be secured using (available from Miele as an optional accessory) into clamps. the dryer's exhaust duct (see Installation instructions). Payment system All COP models are fitted with a connection for a coin control unit. -
Page 24: Electrical Connection
After the dryer has been connected to the electricity In the event of a fault please contact the Miele supply, check the phase rotation on the incoming Professional Service Department. power supply to the appliance. -
Page 25: Technical Data
Technical data Model PT 830x EL/G Height in mm 1800 Width in mm Depth in mm 1063 Depth with door open in mm 1716 Weight in kg 138.8/145.4 Drum volume in l Max. capacity in kg (dry laundry) Voltage See data plate Rated load See data plate Fuse rating... - Page 26 Technical data...
- Page 28 M.-Nr. 09 197 130 / 00 Alteration rights reserved/3412...