Page 1
Manuel d’utilisation Operator’s manual 327LS 327LD X-series Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. C C C C A A A A ( ( ( ( 2 2 2 2 - - - - 2 2 2 2 7 7 7 7 ) ) ) ) U U U U S S S S ( ( ( ( 2 2 2 2 8 8 8 8 - - - - 5 5 5 5 3 3 3 3 ) ) ) )
EXPLICATION DES SYMBOLES Symboles Utiliser des bottes antidérapantes et AVERTISSEMENT! Les stables. débroussailleuses et les coupe- herbes peuvent être dangereux! Une utilisation erronée ou négligente peut occasionner des blessures graves, voire mortelles Destiné uniquement à des pour l’utilisateur ou d’autres équipements de coupe flexibles et personnes.
SOMMAIRE Sommaire Contrôler les points suivants avant la mise en marche: EXPLICATION DES SYMBOLES Symboles .............. 2 Lire attentivement le manuel d’utilisation. SOMMAIRE L’entretien, le remplacement ou la réparation des Sommaire ............. 3 dispositifs et des systèmes antipollution peuvent être Contrôler les points suivants avant la mise en effectués par tout établissement ou personne qui répare marche: ..............
Cher client, Félicitations pour ce choix d’un produit Husqvarna. Husqvarna a vu le jour en 1689 lorsque le roi Karl XI décida de construire un arsenal pour la fabrication des mousquets au bord de la rivière Huskvarna. Le choix de l’emplacement était logique puisque la rivière Huskvarna servait à...
QUELS SONT LES COMPOSANTS? Quels sont les composants? Tête de désherbage 12 Capot de cylindre Ravitaillement en lubrifiant, renvoi d’angle 13 Poignée de lanceur Renvoi d’angle 14 Réservoir d’essence Protection pour l’équipement de coupe 15 Carter de filtre à air Tube de transmission 16 Pompe à...
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Important! AVERTISSEMENT! Ne jamais laisser des enfants utiliser la machine ou se tenir à IMPORTANT! proximité. La machine est équipée d'un interrupteur d'arrêt à détente et peut être La machine est conçue uniquement pour le démarrée par une activation à faible désherbage.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ PROTÈGE-YEUX n'est pas effectuée correctement et si les mesures d'entretien et/ou de réparation ne sont pas effectuées de Toujours porter des protège-yeux homologués. L’usage manière professionnelle. Pour obtenir de plus amples d’une visière doit toujours s’accompagner du port de informations, contacter l'atelier de réparation le plus lunettes de protection homologuées.
Page 8
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Appuyer sur le blocage de l’accélération et vérifier qu’il Protection pour l’équipement de coupe revient de lui-même en position initiale quand il est relâché. Cette protection a pour but d’empêcher que des objets ne soient projetés en direction de l’utilisateur. La protection prévient aussi le contact entre l’utilisateur et l’équipement de coupe.
Page 9
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Le système anti-vibrations réduit la transmission des Ne jamais utiliser une machine dont le silencieux est vibrations de l’unité moteur/l’équipement de coupe à défectueux. l’unité que constituent les poignées. Vérifier régulièrement l’état des éléments afin de détecter fissures et déformations.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Équipement de coupe • La longueur du fil est également importante. Un fil long demande un moteur plus puissant qu’un fil court, Cette section explique comment, grâce à l’utilisation du même en cas de diamètre égal de fil. bon équipement de coupe et grâce à...
MONTAGE Montage de la poignée en boucle • Pousser la fixation dans le raccord jusqu’à ce qu’un déclic indique qu’elle est bien en place. • Placer la poignée anneau sur le tube de transmission. Noter que la poignée anneau doit être montée entre les flèches indicatrices situées sur le tube de transmission.
MONTAGE Montage de l’équipement de • Insérer la goupille d’arrêt (C) dans le trou afin de bloquer l’axe. coupe • Visser la tête de désherbage/les couteaux en plastique (H) dans le sens contraire de la rotation. AVERTISSEMENT! Lors du montage de l’équipement de coupe, il est de la plus grande importance que la commande du bras d’entraînement/de la bride de renfort soit...
Ne jamais utiliser d’huile deux temps pour moteurs hors-bord refroidis par eau, appelée huile outboard (désignation TCW). • Ne jamais utiliser d’huile pour moteurs à quatre temps. • Rapport de mélange 1:50 (2%) avec huile deux temps HUSQVARNA. – French...
MANIPULATION DU CARBURANT Remplissage de carburant Essence, litres Huile deux temps, litres 2% (1:50) 0,10 0,20 AVERTISSEMENT! Les mesures de 0,30 sécurité ci-dessous réduisent le risque d’incendie: 0,40 US gallon US fl. oz. Ne jamais fumer ni placer d’objet chaud à proximité...
DÉMARRAGE ET ARRÊT Contrôles avant la mise en Démarrage et arrêt marche AVERTISSEMENT! Un carter • S’assurer que la bride de support ne présente pas de d’embrayage complet avec tube de fissures par suite d’usure ou de serrage trop fort. En transmission doit être monté...
Page 16
DÉMARRAGE ET ARRÊT Remettre la commande de starter en position initiale dès que le moteur s’allume et continuer les essais de démarrage jusqu’à ce que le moteur démarre. Au démarrage du moteur, donner rapidement les pleins gaz pour désactiver automatiquement l’accélération de démarrage.
TECHNIQUES DE TRAVAIL Méthodes de travail Toujours tenir la machine avec les deux mains. Tenir la machine du côté droit du corps. IMPORTANT! Ce chapitre traite des consignes de sécurité de base lors du travail avec un coupe-herbe. Dans l’éventualité d’une situation rendant la suite du travail incertaine, consulter un expert.
Page 18
TECHNIQUES DE TRAVAIL Techniques de travail de base que le fil dure plus longtemps et la tête de désherbage s’use moins. Ramener le moteur au régime de ralenti après chaque Coupe étape de travail. Laisser le moteur tourner à pleins gaz sans lui faire subir de charge peut endommager •...
Les caractéristiques techniques de cette machine Réglage de base Husqvarna assurent des émissions de gaz nocifs réduites au minimum. Après 8-10 pleins, le moteur est rodé. Pour • Le réglage de base du carburateur est effectué à...
ENTRETIEN Le silencieux est conçu pour atténuer le bruit et dévier le Système de refroidissement flux des gaz d’échappement loin de l’utilisateur. Ces gaz sont chauds et peuvent transporter des étincelles risquant de causer un incendie si elles entrent en contact avec un matériau sec et inflammable.
Huilage du filtre à air d’entraînement sur les modèles démontables (raccords cannelés) risqueraient de gripper. Toujours utiliser l’huile pour filtre HUSQVARNA, réf. 531 00 92-48. L’huile pour filtre contient un solvant permettant une distribution régulière de l’huile dans tout le filtre.
Page 22
Le renvoi d’angle est enduit en usine de la quantité de graisse nécessaire. Toutefois, avant d’utiliser la machine, il convient de s’assurer que le renvoi d’angle est au 3/4 rempli de graisse. Utiliser une graisse HUSQVARNA spéciale. En général, il n’est pas nécessaire de remplacer le lubrifiant du carter, sauf en cas de réparations.
ENTRETIEN Schéma d’entretien La liste ci-dessous indique l’entretien à effectuer sur la machine. La plupart des points sont décrits à la section Entretien. Entretien Entretien Entretien Entretien quotidien hebdomadaire mensuel Nettoyer l’extérieur de la machine. Contrôler le bon fonctionnement du verrou d’accélérateur et de l’accélérateur Contrôler le bon fonctionnement du contacteur d’arrêt.
CARACTÉRISTIQUES TECHNIQUES Caractéristiques techniques 327LDx 327LS Moteur Cylindrée, po 1,50/24,5 1,50/24,5 Alésage, po/mm 1,34/34 1,34/34 Course, po/mm 1,06/27 1,06/27 Régime de ralenti, tr/min 2700 2700 Régime d'emballement maximal recommandé, tr/min 11000-11700 11000-11700 Régime de l’axe sortant, tr/min 8300 8300 Puissance moteur maxi selon ISO 8893, kW/ tr/min 0,9/8400 0,9/8400 Silencieux avec pot catalytique...
Page 25
Accessoire de cultivateur avec tige CA 150 537 42 54-01 Les accessoires ont été développés principalement pour le coupe-bordure Husqvarna 125LD mais peuvent aussi être utilisés avec certaines têtes de coupe ; ils ont été évalués selon les normes de sécurité applicables ISO et EN par l’institut national des tests de l’outillage mécanique.
Page 26
DATE D’ENTRÉE EN VIGUEUR DE LA (California Air Resources Board), Environment Canada et GARANTIE Husqvarna Forest & Garden ont le plaisir d’expliquer la garantie relative au système de contrôle des émissions La période de garantie commence à la date à laquelle le des petits moteurs fabriqués en 2009 et ultérieurement.
Page 27
DEMANDE D’INDEMNITÉ Si vous avez des questions concernant vos droits et charges en garantie, contactez votre revendeur autorisé le plus proche ou téléphonez à Husqvarna Forest & Garden, au numéro suivant: +1-800-487-5951 ou visitez www.usa.husqvarna.com. SERVICE APRÈS-VENTE Les révisions ou réparations sous garantie sont disponibles auprès de tous les revendeurs agréés...
KEY TO SYMBOLS Symbols Only use non-metallic, flexible WARNING! Clearing saws, cutting attachments, i.e. trimmer brushcutters and trimmers can be heads with trimmer cord. dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the Other symbols/decals on the machine refer to...
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............28 Please read the operator’s manual carefully. CONTENTS Maintenance, replacement, or repair of the emission Contents ............... 29 control devices and system may be performed by any Note the following before starting: ......29 nonroad engine repair establishment or individual.
Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets.
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can The only accessories you can operate with this engine cause serious or fatal injury to the operator or others.
GENERAL SAFETY PRECAUTIONS BOOTS control (B). When you release the handle the throttle control and the throttle lockout both move back to their Wear sturdy, non-slip boots. original positions. This movement is controlled by two independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.
Page 34
GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Vibration damping system Maintenance. Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Stop switch Use the stop switch to switch off the engine. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration.
GENERAL SAFETY PRECAUTIONS In countries that have a warm and dry climate there is a WARNING! Bear in mind that: significant risk of fire. We therefore fit certain mufflers with a spark arrestor screen. Check whether the muffler on your machine is fitted with this kind of screen. The exhaust fumes from the engine are hot and may contain sparks which can start a fire.
GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size.
ASSEMBLY Fitting the loop handle • Before using the unit, tighten the knob securely. • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Dismantling: • Loosen the coupling by turning the knob (at least 3 times).
ASSEMBLY Assembling the cutting • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. equipment WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of •...
Two-stroke oil long-term storage, if the machine is not under close supervision and when performing all service • For best results and performance use HUSQVARNA measures. two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. WARNING! Take care when handling fuel.
FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.
STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to WARNING! The complete clutch cover fatigue or due to being tightened too much. Discard and shaft must be fitted before the the support flange if it is cracked.
Page 42
STARTING AND STOPPING apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.
WORKING TECHNIQUES General working instructions Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.
Page 44
WORKING TECHNIQUES Basic working techniques Cutting • The trimmer is ideal for cutting grass that is difficult to Always slow the engine to idle speed after each working reach using a normal lawn mower. Keep the cord operation. Long periods at full throttle without any load on parallel to the ground when cutting.
Carburetor the optimal setting and should be maintained for the first few hours the machine is in use. The carburettor Your Husqvarna product has been designed and should then be finely adjusted. Fine adjustment manufactured to specifications that reduce harmful should be carried out by a skilled technician.
MAINTENANCE cause fire if directed against dry and combustible Cooling system material. To keep the working temperature as low as possible the machine is equipped with a cooling system. Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week.
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.
However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily Weekly Monthly Maintenance maintenance maintenance maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.
TECHNICAL DATA Technical data 327LDx 327LS Motor Cylinder displacement, cu.in/cm 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34 1,34/34 Stroke, inch/mm 1,06/27 1,06/27 Idle speed, rpm 2700 2700 Recommended max. speed, rpm 11000-11700 11000-11700 Speed of output shaft, rpm 8300 8300 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8400 0,9/8400 Catalytic converter muffler...
Page 51
537 42 54-01 The accessories have been developed mainly for the Husqvarna 125LD trimmer, but can also be used in combination with the specified power heads and have been evaluated to applicable ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute.
If the part fails prior to the first scheduled replacement, Husqvarna Forest & Garden. the part will be repaired or replaced by Husqvarna Forest & Garden at no cost. Any such part repaired or replaced OWNER′S WARRANTY...
Page 53
EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.