Advertisement
Quick Links
Before attempting to connect or operate this product, please read these instructions completely
Caution
When handling this board, hold only by circuit board edges. Otherwise components on the
board may be damaged by static electricity.
PREFACE
The WV-PB5504AE Video Output Board is provided for expanding the video output capability of the
Matrix Switcher.
APPEARANCE
1.
Alarm Output/Reset Output Connector (ALARM OUT/RESET OUT)
External Timing Input Connector (EXT TIMING IN)
Recover Input Connector (RECOVER IN)
ALARM OUT: When the Matrix Switcher receives an alarm from the WV-PB5564E Alarm Board
or camera site receivers WV-RC100, WV-RC150 or WV-RC170, the alarm output signal is
provided at this connector for the Time Lapse VTR. The active pin number of the alarm out-
put depends on the alarm mode set by the on-screen programme (Mode-1, Mode-2,
Mode-3).
RESET OUT: When the Matrix Switcher resets the activated alarm, the alarm reset output sig-
nal, either Open Collector or pulse, is provided at this connector for the Time Lapse VTR.
EXT TIMING IN: The camera switching interval (Sequential Dwell Time) can be synchronized
with the lapse mode set in the Time Lapse VTR.
EXT. TIMING IN 1 controls Monitor 1 output, EXT. TIMING IN 2 controls Monitor 2 output, etc.
Supply the camera switching pulse from the Time Lapse VTR to this connector. Minimum
duration for camera switching pulse needs to be more than one (1) second.
RECOVER IN: This connector accepts the alarm recover signal from the Time Lapse VTR.
25
24
23
22
21
20
19
18
17
16
15
14
Pin No.
1
2
3
13
4
5
12
6
11
7
10
8
9
9
10
8
11
12
7
13
6
14
5
15
16
4
17
3
18
2
19
20
1
21
22
23
24
25
WV-PB5504AE
Designation
ALARM OUT 1
RESET OUT 1
RECOVER IN 1
Ground
EXT TIMING IN 1
Ground
ALARM OUT 2
RESET OUT 2
RECOVER IN 2
Ground
EXT TIMING IN 2
(+5V DC)
ALARM OUT 3
RESET OUT 3
RECOVER IN 3
Ground
EXT TIMING IN 3
Ground
ALARM OUT 4
RESET OUT 4
RECOVER IN 4
Ground
EXT TIMING IN 4
Ground
Ground
-1-
Video Output Board
OUTPUT
q
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
MONITOR
IN
1
OUT
IN
2
OUT
w
IN
3
OUT
IN
4
OUT
Advertisement
Related Manuals for Panasonic WV-PB5504AE
Summary of Contents for Panasonic WV-PB5504AE
- Page 1 When handling this board, hold only by circuit board edges. Otherwise components on the board may be damaged by static electricity. PREFACE OUTPUT The WV-PB5504AE Video Output Board is provided for expanding the video output capability of the Matrix Switcher. APPEARANCE Alarm Output/Reset Output Connector (ALARM OUT/RESET OUT)
- Page 2 Monitor Input/Output Connector (MONITOR IN/OUT) OUT: The video signal selected by the Matrix Switcher is provided at this connector for the video monitor. IN: This connector is used for video input from a VTR or system expansion to 128 camera input. BOARD SETTING Before installing this board, the following settings should be made by qualified service personnel or system installers.
- Page 3 3. Set switches (SW100/SW150/SW200/SW250) on the board to choose the character display mode on the monitor. NOR: White with Black border REV: Black with White border Initially, normal (NOR) positions are selected at the factory. MONITOR OUT NO. BOARD SW100 SW150 SW200 SW250 NOR Position REV Position 1 (5)
- Page 4 Tighten screws. 4. Make sure to push in the Video Output Board until it is Blank Panel seated firmly. 5. Secure the Video Output Board by tightening the two screws on the board. 6. Close off open spaces on the rear of the Matrix Switcher by using WV-Q63E Blank Panels (Optional) or supplied rear panel(s).