Troubleshooting - Panasonic CQ-C1301NW Operating Instructions Manual

General
[VOL] (Volume) Remote control sensor
for an optional remote control unit (CA-RC61EX).
BAND
APM
PWR
MUTE/SQ
SRC SRC
[SRC] (Source)
[MUTE]
selects a source. toggles mute on/off.
(PWR) (Power) (SQ) (Sound Quality)
toggles power on/off. selects a sound type (SQ). (Hold it down for
more than 1 second.)
Power On/Off
Set your car's ignition switch to the ACC or ON position.
Power on: Press [SRC] (PWR).
Power off: Hold down [SRC] (PWR) for
more than 1 second.
Source Selection
Press [SRC] to change the source.
Radio Disc Player
Volume Adjustment
(Setting Range: 0 to 40, Default: 18)
Turn [VOL].
Mute
ON: Press [MUTE].
( lights.)
OFF: Press [MUTE] again.

Troubleshooting

If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recom-
mended to take the unit to your nearest authorized Panasonic Service
Centre. The product should be serviced only by qualified personnel.
Please refer the checking and the repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking.
Trouble
Check point
Common
●
Start the engine. (Or turn the ignition
switch to the ACC position.)
●
Verify the wiring. (battery lead, power
lead, ground lead, etc.)
No power
●
Fuse blown (Contact the nearest
Panasonic Service Centre.)
●
Ask a professional for fuse replacement.
●
Be sure to use the same rated fuse.
●
Disable the mute function.
●
Verify the wiring.
No sound
●
Wait until the dew disappears before
turning on the unit.
●
Make sure that grounding is established
Noise
properly.
No sound from
●
Adjust the balance and fader.
left, right, front,
●
Verify the wiring.
or rear speaker
Left and right
●
sounds are Connect the speaker lead correctly.
reversed
Disc Player
No sound, or disc
●
Load the disc correctly.
is automatically
●
Clean the disc.
ejected
Sound skip,
●
poor sound Clean the disc.
quality
●
Sound skip
The maximum permissible tilt angle is
due to 30°.
●
Secure the unit.
vibration
●
u
Press [ ]. If the disc is still not ejected,
Disc not
contact the nearest Panasonic Service
ejectable
Centre.
CQ-C1321N
PTY
SCROLL RANDOM SCAN REPEAT TA/AF
DISP
1 2 3 4 5 6
SQ (Sound Quality)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
1
Holding down [SQ] for more than 1 sec-
ond activates the SQ selection mode.
2
Press [SQ] to select the sound type (SQ)
as follows:
(FLAT) flat frequency response:
does not emphasize any part. (Default)
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
(VOCAL) clear sound:
emphasizes middle tone and slightly empha-
sizes treble.
Notes:
¡ If no operation takes place for more than 5 seconds in
the SQ selection mode, the display returns to the regular
mode.
¡ Settings of SQ, bass and treble are influenced one anoth-
er. If such an influence causes distortion to the audio
signal, readjust bass/treble or volume.
Warning
¡ Do not use the unit in an irregular condition, for example, with-
out sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡ Never try to repair the unit by yourself because it is dangerous
to do so.
Trouble
Check point
Radio
●
Tune in to another station of high-inten-
Frequent
sity waves.
●
noise Make sure that the antenna mounted
point is grounded properly.
●
The preset memory is cleared to return
Preset data
to the original factory setting when the
deleted power connector or battery is discon-
nected.
Error Display Messages
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
●
Check the disc.
(The disc is ejected automatically.)
The disc has scratches.
●
Check the disc.
No operation by some cause.
●
If normal operation is not restored, con-
sult your dealer or the nearest Service
Centre to ask for repairs.
Cannot read the file
●
Check the file.
A WMA file can be copyrighted.
●
The file protected by copyright is not
playable.
Radio (AM [LW/MW] /FM)
[BAND]
selects a band in the radio source.
(APM) ( Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
BAND BAND
APM
PWR
MUTE/SQ
SRC SRC
[SRC] (Source) [1] to [6]
selects a source. selects a preset station in the radio source,
and presets the current station. (Hold it down
for more than 2 seconds.)
1
Press [SRC] to select the radio source.
2
Press [BAND] to select a band.
Radio Data System (RDS) in FM Broadcasting
Useful functions such as AF, TA, PTY are available in the RDS (Radio Data System)-ready areas.
Some FM stations are broadcasting added data compatible
with RDS. This radio set offers convenient functions using
such data.
RDS service availability varies with areas. Please understand if
RDS service is not available in your area, the following service
is not available, either.
The following functions are available when receiving RDS
stations.
AF (Alternative Frequency)
The following functions are available when the AF mode is
active ( lights).
¡ When receiving conditions become bad, a station with bet-
ter receiving conditions is automatically tuned in to.
¡ When executing APM, only RDS stations are selected.
¡ When calling up a preset station, a best receiving station is
selected automatically. (BSR Best Stations Research)
Notes:
¡ The AF sensitivity can be adjusted.
¡ The AF available range can be adjusted.
Settings")
TA (Traffic Announcement)
The following functions are available when the TA mode is active
( lights).
¡ A TP station is automatically searched for and received at
the instant of toggling the TA mode on if you are receiving
a non-TP station or TP station with poor reception.
When executing station search or APM, only TP stations
¡
are selected.
AF Level
Hold down [TA] (AF) for more than 2 seconds to select AF
level.
Low level AF operating sensitivity. (Default)
High level AF operating sensitivity.
When the AF network of an RDS station is not
required.
CQ-C1321N
PTY
SCROLL RANDOM SCAN REPEAT TA/AF [DISP] (Display)
DISP DISP
1 1 2 2 3 3 4 4 5 5 6 6
switches the information on
the display.
[TUNE ]] [TUNE []
down/up the frequency. (Hold it down for
more than 0.5 seconds and release it for seek
tuning.)
3
Select a station.
Frequency adjustment
[TUNE ]]: Lower
[TUNE []: Higher
Note: Hold down either of them for more than 0.5 sec-
onds and release it for seek tuning.
Preset station selection
Press the corresponding preset button from [1] to [6] to
tune into a preset station.
¡ Setting to TA on with the unit in another mode, it will auto-
matically switch to radio mode and output the traffic
announcement when the traffic announcement begins. The
traffic announcement having finished, the unit will return to
the previous mode. (TA Standby Mode)
PTY (Programme Type)
The following functions are available when the PTY mode is
active.
¡ The PTY of receiving station appears.
¡ Programs can be searched for by PTY.
Note: PTY language can be selected.
Other functions of RDS
CT (Clock Time)
The clock is automatically adjusted.
PS (Programme Service Name)
As well as the frequency, the name of the broadcast station
appears.
(a "Function
EON (Enhanced Other Network)
RDS information is updated constantly in response to the
current position.
EON-TA
Traffic information from the current and other network
stations can be received.
Emergency Announcement Reception
Emergency announcement automatically appears on the
display when it is received.
PI Seek (Programme Identification Seek)
If reception becomes poor when tuning in a preset station,
press the same preset number button. The same station with
better reception will be searched for.
Press same preset number button again to cancel.
Note: For PI Seek, cancel the TA mode first, then execute PI
Seek.
(a "Function Settings")