Table of Contents
Advertisement
Note: Incorrect operations may be performed if the test mode is not
entered properly.
In this case, press the [
retry to enter the test mode.
1. Cold Reset
•
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customers.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press three buttons [
], [
x
A
3. When this button is operated, display as "COLD RESET" for
a while and all of the settings are reset.
2. Panel Test Mode
•
This mode is used to check the software version, FL and
KEY.
2-1. Display Test Mode
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press three buttons [
], [
X
.
3. When the display test mode is activated, all segments are turned
on.
4. To exit from this mode, press three buttons [
simultaneously.
2-2. Version Test Mode
Procedure:
1. When the display test mode is activated, press the [
and the message "DSR2K–" (DZ265K), "DSR2K+" (DZ266K),
"DSR2K" (DZ270K), "DSR4K" (DZ570K), "DSR7K" (DZ777K)
are displayed, the version test mode is activated.
2. Whenever the [
] button is pressed, the display changes in
.
the following order.
"DSR7K" (Model name)
"ASIA2
MC Version
SYS Version
DVD Version
ST Version
DSP Version
TM Version
CLA Version
CEC Version
*1: ASIA2 changes depending on destination.
3. Press the [
] button and the date of the software production
>
is displayed.
4. Press the [
] button again and the version is displayed.
>
5. To exit from this mode, press three buttons [
simultaneously.
2-3. Key Test Mode
Procedure:
1. When the display test mode is activated, press the [
to select the key test mode.
2. To enter the KEY test mode, the fl uorescent indicator displays
"K0 V0". Each time an another button is pressed, "KEY" value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, "K8
V0" is displayed.
3. When the [VOLUME] control is turned in the direction of (+),
"V0" is changed to "V1", then ... "V9".
When the [VOLUME] control is turned in the direction of (–),
"V0" is changed to "V9", then ... "V1".
4. To exit from this mode, press three buttons [
simultaneously.
HCD-DZ265K/DZ266K/DZ270K/DZ570K/DZ777K
SECTION 4
TEST MODE
] button to turn the power off, and
?/1
] and [
] simultaneously.
?/1
] and [
] simultaneously.
A
], [
] and [
X
.
] button
.
" (Destination)
*1
UI Version
TA Version
MM Version
SAIR Version
], [
] and [
X
.
] button,
H
], [
] and [
X
.
3. Disc Tray Lock
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the [
] button to turn the set on.
?/1
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the [
] button and the [
x
seconds.
5. The message "LOCKED" is displayed and the tray is locked.
Releasing Procedure :
1. Press the [
] button and the [
x
seconds again.
2. The message "UNLOCKED" is displayed and the tray is
unlocked.
Note: When "LOCKED" is displayed, the tray lock is not released by
turning power on/off with the [
4. DVD Ship Mode
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
] button to turn the set on.
?/1
2. Press the [FUNCTION] button to set the function "DVD".
3. Remove all Discs, and then press two buttons [
simultaneously.
4. After a message "MECHA LOCK" h "PULL PLUG" is
]
displayed on the fl uorescent indicator tube, pull out the AC
A
plug.
5. To exit from this mode, press the [
on.
5. AM Step Change (Except RU models)
•
A step of AM channels can be changed over between 9 kHz
and 10 kHz.
Procedure:
1. Press the [
] button to turn the set ON.
?/1
2. Select the function "TUNER", and press [FUNCTION] button
to select the BAND "AM".
3. Press the [
] button to turn the set OFF.
?/1
4. Press two buttons [
display of fl uorescent indicator tube changes to "AM 9k STEP"
or "AM 10k STEP", and thus the channel step is changed
over.
6. Product Out
This mode moves the optical pick-up to the position durable to
]
vibration and clears all data including preset data stored in the
A
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press the [FUNCTION] button to set the function "DVD".
3. Remove all discs, and then press three buttons [
[
] simultaneously.
?/1
4. After the "STANDBY" blinking display fi nishes, the message
"MECHA LOCK" h "PULL PLUG" is displayed on the
fl uorescent indicator tube disconnect the AC power plug, then
the ship mode is set.
]
A
] button simultaneously for fi ve
A
] button simultaneously for fi ve
A
] button.
?/1
H
] button to turn the set
?/1
] and [
] simultaneously, and the
>
?/1
>
] and [
]
?/1
], [
] and
A
25
Hide quick links:
Advertisement
Table of Contents
