HP 2530 Quick Setup Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Switch
  5. HP 2530
  6. Quick setup manual
HP 2530 Quick Setup Manual

HP 2530 Quick Setup Manual

24-port and 48-port switches
Hide thumbs Also See for 2530:
Table of Contents

Advertisement

Quick Links

HPE 2530 24-Port and 48-Port Switches

Quick Setup Guide

The switch drawings in this document are for illustration only and may not match your particular switch
model.
For more detailed instructions and information to set up your switch, view or download the Installation
and Getting Started Guide for your switch at http://www.hpe.com/networking/support.
1.
Unpack and check included parts.
Documentation kit
Switch
Console port serial cable (DB-9 to RJ-45)
Accessory kit (installation hardware)
AC power cord
2.
Prepare for installation. To avoid personal injury or product damage, review
Information for HPE 2530 24/48-Port Switches" (page
3.
Power on and verify that Self-Test completes normally. Power on the switch by connecting the power
cord through the AC power connector and switch on the power switch.
*5900-4818*
© Copyright 2014, 2015 Hewlett Packard Enterprise Development LP
The information in this document is subject to change without notice.
Part Number: 5900-4818
Published: November 2015
Edition: 2
4).
"Safety and Regulatory

Advertisement

Table of Contents
loading

Related Manuals for HP 2530

Summary of Contents for HP 2530

  • Page 1: Quick Setup Guide

    Prepare for installation. To avoid personal injury or product damage, review “Safety and Regulatory Information for HPE 2530 24/48-Port Switches” (page Power on and verify that Self-Test completes normally. Power on the switch by connecting the power cord through the AC power connector and switch on the power switch.
  • Page 2 NOTE: The HPE 2530 24-port and 48-port switches can also be mounted in 4-post racks and cabinets by using the HPE X410 Switch Rail Kit (J9583A). For instructions on using the kit, see the documentation that is included with the kit.

  • Page 3: Sfp Installation Notes

    “SFP Installation Notes” (page (Optional) Configure the switch for management. By factory default, the switch will automatically obtain its IP network configuration from a DHCP or BootP server. Subsequently, you can determine the IP address assigned to the switch by inspecting your DHCP/BootP server or by using LLDP from a connected device.

  • Page 4: Installation Precautions

    Environmental limitations. If using SFPs with the switch, ensure that the operating temperature range at the switch installation site does not exceed the range allowed for the SFP. Safety and Regulatory Information for HPE 2530 24/48-Port Switches To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below.

  • Page 5: Regulatory Information

    DIN 45635 T.19 DIN 45635 T.19 DIN 45635 T.19 The HPE 2530 switches automatically adjust to any voltage between 100–127 and 200–240 volts and either 50 or 60 Hz. All HPE 2530 24-Port and 48-Port Switches Environmental: Operating Temperature: 0°C to 45°C (32°F to 113°F)

  • Page 6: Power Cord

    8120-5334 United States/Canada/Mexico 8120-6805 8121-0973 The power cord for the HPE 2530-48G-PoE+-2SFP+Switch supports a higher amperage and uses a C15 connector. WARNING! Japan Power Cord: Important Note for the 2530-PoE+ Switches For PoE/PoE+ information see the HPE Power over Ethernet (PoE/PoE+) Planning and Implementation Guide on the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/support.

  • Page 7: Documentation Feedback

    In the first text box, type J4858 (for 100-Mb and Gigabit information) or J8436 (for 10-Gigabit information). Select any of the products that display in the drop down list. Select Product support information. Then click on Manuals and find the Transceiver Support Matrix.
  • Page 8 *5900-4818* Printed in the US...

Table of Contents