Panasonic PT-LB1E Operating Instructions Manual
Network operation manual
Hide thumbs
Also See for PT-LB1E:
- Operating instructions manual (59 pages) ,
- Brochure & specs (6 pages) ,
- Operating instructions manual (19 pages)
Table of Contents
Related Manuals for Panasonic PT-LB1E
Summary of Contents for Panasonic PT-LB1E
-
Page 1: Operating Instructions
Operating Instructions Network Operation Manual PT-LB2E/LB2EA/LB2U Model No. PT-LB1E/LB1EA/LB1U LCD Projector AUTO SETUP MENU RETURN ENTER FREEZE MUTE COMPUTER VIDEO DEFAULT FUNCTION INDEX- WIN. DIGITAL ZOOM VOLUME TQBH0215-1 (E/U/EA) -
Page 2: Table Of Contents
Network setting of the projector · · · · · · · · · · · · · · · · · ·... -
Page 3: Request Regarding Security
• Panasonic Corporation and its affiliated companies never directly ask customers for their password. Do not give out your password even if directly asked by a third-party representing themselves as Panasonic Corporation. • Always use on a network that has safety protection such as a firewall implemented. -
Page 4: Check Your Computer
Connection can be made with wired LAN. However, confirm to your system administrator on network settings before changing any settings. Turn on the computer. Make the network setting according to your system administrator. If the projector settings are the default settings (See page 6), the computer can be used with the following network settings. IP ADDRESS SUBNETMASK DEFAULT GATEWAY function. -
Page 5: Network Setting Of The Projector
You can select the sub-menu item. Depending on the signals which are input to the projector, it may not be possible to adjust some of the items and use some of the functions. In the case of an item that cannot be adjusted or a function that cannot be used, the corresponding on-screen item will not be displayed, and you will not be able to execute it even when you press the [ENTER] button. -
Page 6: Network
CANCEL SELECT DHCP If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired. OFF: If a DHCP server does not exist in the network to which the projector is connected, additionally set [IP ADDRESS ], [SUBNETMASK ] and [DEFAULT GATEWAY ]. -
Page 7: Name Change
Select [OK] with the [◄►▲▼] buttons and press the [ENTER] button. Select [CANCEL] to undo the changes. NETWORK CONTROL Set it to “ON”, if you want to control the projector from a computer that is network-connected. Select [NETWORK CONTROL] in the NETWORK menu. PICTURE WIRED LAN... -
Page 8: Status
MAC ADDRESS — MAC ADDRESS : “Glossary” (See page 18) INITIALIZE You can reset the network settings to the factory default settings of the projector. Select [INITIALIZE] in the NETWORK menu and press the [ENTER] button. PICTURE WIRED LAN POSITION... -
Page 9: Using Webbrowser
Using WebBrowser Control a projector through the WebBrowser of a computer. It is called “WEB Control”. (The example is when using Microsoft Internet Explorer.) Before using the WEB control Connect the projector and a computer with a LAN cable. (See page 4) Projector settings Turn [ON] the [NETWORK CONTROL] in the NETWORK menu. -
Page 10: Accessing From The Webbrowser
The system locks for several minutes if an incorrect password is entered three times in succession. • If you initialize the network settings, the password is reset to “panasonic”. Change the password to an appropriate one. • Make sure the password is as hard to guess as possible. -
Page 11: Monitor Information Window
There is a problem with a microcontroller circuit. Contact your dealer. There is a problem with the fan or fan drive circuit. Contact your dealer. Input air temperature is high. The projector is likely being used in a high temperature environment such as near heating equipment. -
Page 12: Projector Control Window
„ On this window, click the [Basic control] tab. Connection with the projector may not be possible immediately after the power is turned on. In this case wait a bit and then make the connection again. Detailed set up window Network config „... -
Page 13: Adjust Clock
Using WebBrowser Complete the detailed settings and click [Next]. When [Next] is clicked, the next page appears, enabling you to complete the detailed settings as desired. After all required items have been entered, a confirmation window appears. Click [Submit]. The settings will be registered. If you have changed the LAN settings that are currently in use, the connection may break off. -
Page 14: Ping Test
INPUT AIR TEMPERATURE : Select ON to send email when the temperature set in [TEMPERATURE WARNING SET UP] is exceeded. PERIODIC REPORT : Send a message with the projector status at the selected date and time. When [submit] is clicked, the settings are applied. Consult your system administrator on MAIL SERVER and E-MAIL ADDRESS settings. - Page 15 Using WebBrowser Example of email message sent If [NORMAL] is selected under [MAIL CONTENTS] „ If you have completed the email settings ＝＝＝ Ｐａｎａｓｏｎｉｃ ｐｒｏｊｅｃｔｏｒ ｒｅｐｏｒｔ（ＣＯＮＦＩＧＵＲＥ） ＝＝＝ Ｐｒｏｊｅｃｔｏｒ Ｔｙｐｅ ： ＬＢ２ Ｓｅｒｉａｌ Ｎｏ ： Ｄ２３４５６７ＡＢ －－－－－ Ｅ－ｍａｉｌ ｓｅｔｕｐ ｄａｔａ －－－－－ ＴＥＭＰＥＲＡＴＵＲＥ ＷＡＲＮＩＮＧ ＳＥＴＵＰ ＭＩＮＩＭＵＭ ＴＩＭＥ ａｔ ［ ６０］ ｍｉｎｕｔｅｓ ｉｎｔｅｒｖａｌ ＩＮＰＵＴ ＡＩＲ ＴＥＭＰＥＲＡＴＵＲＥ Ｏｖｅｒ ［ ３８Ｃ ／ １００Ｆ ］ ＥＲＲＯＲ ［ ＯＮ ］ ＬＡＭＰ ＲＵＮＴＩＭＥ ［ ＯＮ ］ ａｔ ＲＥＭＡＩＮ ［ ４００］ Ｈ ＬＡＭＰ ＲＵＮＴＩＭＥ ［ ＯＮ ］ ａｔ ＲＥＭＡＩＮ ［ ２００］ Ｈ ＩＮＰＵＴ ＡＩＲ ＴＥＭＰＥＲＡＴＵＲＥ ［ ＯＮ ］ ＰＥＲＩＯＤＩＣ ＲＥＰＯＲＴ Ｓｕｎｄａｙ ［ ＯＮ ］ Ｍｏｎｄａｙ ［ ＯＮ ］ Ｔｕｅｓｄａｙ ［ ＯＮ ］ Ｗｅｄｎｅｓｄａｙ ［ ＯＮ ］ Ｔｈｕｒｓｄａｙ ［ ＯＮ ］ Ｆｒｉｄａｙ ［ ＯＮ ］ Ｓａｔｕｒｄａｙ ［ ＯＮ ］ ００：００ ［ ＯＮ ］ ０１：００ ［ ＯＮ ］ ０２：００ ［ ＯＮ ］ ０３：００ ［ ＯＮ ］ ０４：００ ［ ＯＮ ］ ０５：００ ［ ＯＮ ］ ０６：００ ［ ＯＮ ］ ０７：００ ［ ＯＮ ］ ０８：００ ［ ＯＮ ］ ０９：００ ［ ＯＮ ］ １０：００ ［ ＯＮ ］ １１：００ ［ ＯＮ ］ １２：００ ［ ＯＮ ］ １３：００ ［ ＯＮ ］ １４：００ ［ ＯＮ ］ １５：００ ［ ＯＮ ］ １６：００ ［ ＯＮ ］ １７：００ ［ ＯＮ ］ １８：００ ［ ＯＮ ］ １９：００ ［ ＯＮ ］ ...
-
Page 16: Change Password Window
Using WebBrowser Authentication set up „ Click [Detailed set up] → [Authentication set up] in the menu. Auth : Change the authentication method as desired. SMTP Auth : For SMTP authentication, change the authentication method to use, as desired. Pop Server name : Enter the POP server name. -
Page 17: Using Pjlink Protocol
Setting the projector • Querying the projector status To use PJLink protocol, turn [ON] the [NETWORK CONTROL] in the NETWORK menu for the projector. (See page 7) Applicable commands The following commands are used to control the projector with the PJLink protocol. -
Page 18: Glossary
Unauthorized use or reproduction of part or all of this manual is strictly prohibited. • Panasonic cannot be held liable for any effects resulting from the use of this manual. • Panasonic reserves the right to revise this manual contents without notice. - Page 19 Web Site : http://panasonic.net/avc/projector/ © Panasonic Corporation 2010 F0510-10710A...