1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Security Camera
  5. Super Dynamic III WV-CW480S
  6. Operating instructions manual

Panasonic WV-CW480S Operating Instructions Manual

Colour cctv cameras
Hide thumbs Also See for WV-CW480S:
Table of Contents

Advertisement

Quick Links

Colour CCTV Cameras

Operating Instructions

WV-CW484F
Model Nos.
WV-CW480S
WV-CW484F is shown above.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
No model number suffix is shown in this manual.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic WV-CW480S

Summary of Contents for Panasonic WV-CW480S

  • Page 1: Operating Instructions

    Colour CCTV Cameras Operating Instructions WV-CW484F Model Nos. WV-CW480S WV-CW484F is shown above. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual.
  • Page 2 ENGLISH VERSION WARNING: • This apparatus must be earthed. • Apparatus shall be connected to a mains sock- et outlet with a protective earthing connection. • The mains plug or an appliance coupler shall remain readily operable. • All work related to the installation of this prod- uct should be made by qualified service per- sonnel or system installers.

  • Page 3: Table Of Contents

    Important Safety Instructions ... 4 Limitation of Liability ... 5 Disclaimer of Warranty ... 5 Preface ... 6 Features ... 6 Precautions ... 7 Major Operating Controls and Their Functions ... 10 Installations ... 12 Image Adjustment ... 20 Connections ... 22 About Setup Menus ...

  • Page 4: Important Safety Instructions

    Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Clean only with dry cloth. 6) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 7) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

  • Page 5: Limitation Of Liability

    Limitation of Liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WAR- RANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT PARTY'S RIGHT. Disclaimer of Warranty IN NO EVENT SHALL MATSUSHITA ELEC- TRIC INDUSTRIAL CO., LTD.

  • Page 6: Preface

    (Power source: 12 V DC/24 V AC) • WV-CW480S: This is a model with 2x variable focal lens. Mounting bracket is provided, but ceiling mount bracket is optional. (Power source: 220 V to 240 V AC) Features •...

  • Page 7: Precautions

    This apparatus has no power switch. Power is supplied from an external 12 V DC/ 24 V AC (WV-CW484F) or 220 V to 240 V AC (WV-CW480S) power-supply device. Refer to service personnel for how to turn on/off the power.
  • Page 8 About the dehumidifying device • The camera has dehumidifying device to keep the inside at low moisture level, preventing condensation and quickly dis- sipating dew if produced. • Dew may be produced depending on the conditions temperature, winds, and rain, and it may take time to dehumidify.
  • Page 9 Consumable parts Contact your dealer for replacement of the following part when the time comes: Cooling fan needs replacement after around 30 000 hours of operation. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera at temperatures within –10 °C to +50 °C, and humidity below 90 %.

  • Page 10: Major Operating Controls And Their Functions

    Major Operating Controls and Their Functions !5 5...
  • Page 11 • Supplies 24 V AC or 12 V DC from an external power source. (WV-CW484F) • Supplies 220 V to 240 V AC from an external power source. (WV-CW480S) w Video output cable with BNC connec- Connects wih the video connector.

  • Page 12: Installations

    • Mounting Bracket (WV-Q114) is optional for WV-CW484F. Use the screws provided to the Mounting Bracket. • Mounting Bracket is provided to WV-CW480S. Use the screws (M4 x 8, 4 pcs.) provided to this product. Important: • Prepare four fixing screws to be used to mount the provided camera attachment according to the material of the area where the attachment is to be installed.
  • Page 13 I Installations (WV-CW484F) G Using a Junction Box Secure the provided camera attachment to the two gang junction box built in a wall or ceiling. G Using Mounting Bracket WV-Q114 (Option) • Secure the optional camera mounting bracket to wall or ceiling, and fix the provided cam- era attachment to the mounting bracket with the screws for the mounting bracket.
  • Page 14 <Fixing the camera attachment to the mounting bracket> I Installations (WV-CW480S) G Using Provided Mounting Bracket • Secure the provided camera mounting bracket to wall or ceiling, and fix the provided cam- era attachment to the mounting bracket with the screws for to the mounting bracket. (Refer to the following figures.)
  • Page 15 <Fixing the camera attachment to the mounting bracket> I How to mount the camera (WV-CW484F, WV-CW480S) 1. Connect the power cable and the BNC plug of the video output cable. (Refer to p. 22 Connections.) 2. Secure the camera with four attachment fixing screws.
  • Page 16 3. Hook the rear screws on the screw holes of camera attachment, and turn the cam- era unit clockwise to fix the camera unit and camera attachment. 4. Remove the enclosure from the main body by loosening the three fixing screws.
  • Page 17 6. Secure the camera unit to the bracket with the camera lock screw. 7. Adjust the camera. (Refer to p. 20.) 8. Attach the enclosure to the camera. Firmly tighten the three tamper-proof screws. (Recommended tightening torque: 0.78 N·m) Notes: •...
  • Page 18 I Waterproof Process • When routing cables sideway using Mounting Bracket or installing the camera under eaves, apply waterproof process to the cable and relevant portions. • The cables are not waterproofed. Provide water sealing for the tube ends and the portions between cable cores as well as connecting portions.
  • Page 19 Notes: • Surely attach a pipe fitting to the bracket to avoid exposing the cables. Otherwise, cable deterioration resulting from cable exposure may cause a short circuit. • Run the conduit downward or pull the conduit out of the side of the bracket. When pulling the conduit out of the side of the bracket, run the conduit downward once, and upward.

  • Page 20: Image Adjustment

    Image Adjustment You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor. Notes: • When connecting an LCD monitor to adjust the camera images, use an L-type mini plug. Straight type plugs are not available. •...
  • Page 21 5. Aim the camera at the targeting objects and if applicable adjust the zoom angle. 6. Press the [ABF1] button. → The LED indicator will light up, and a bar graph with "I" cursor and INDICATOR (4-digit number) will be overlaid on the camera picture. →...

  • Page 22: Connections

    WV-CW480S: Approx. 183 cm) Video output cable (WV-CW484F: Approx. 22 cm, WV-CW480S: Approx. 42 cm) G Video Output Connection Connect the video output connector to the monitor or other system device with the pro- cured coaxial cable. The maximum extensi- ble length is shown in the table.
  • Page 23 24 V AC (WV-CW484F) or 220 V to 240 V AC (WV-CW480S) power source. • Shrinking the cable-entry seal is a one- time procedure. Do not shrink the cable entry seal until it has been ascertained that unit is functioning.
  • Page 24 I Optional Heater Unit WV-CW4H G Introduction Installing this heater unit enables the camera to operate in a low-temperature environment below –30 °C. The heater turns on automatically when the temperature inside the camera drops below +10 °C and turns off when the temperature rises. A small fan inside the unit will minimize condensation on the surface of the enclosure caused by changes in ambient temperature unless temperatures change too rapidly.

  • Page 25: About Setup Menus

    About Setup Menus Before operation, setup of this camera is required. On the setup menu, you can check current settings and perform settings to meet requirements. The following is an example of setup procedure when LANGUAGE is set to ENGLISH. Settings items of the camera setup page Setup item CAMERA...
  • Page 26 Setup item SPECIAL CHROMA GAIN AP GAIN PEDESTAL PIX OFF CAMERA RESET SER.NO. LANGUAGE Description Adjust the chroma level (colour density). Adjust the aperture level. Adjust the pedestal level (brightness). Correct image defects such as scratches. Reset the settings of setup menu to the default set- tings.

  • Page 27: I Basic Operation

    SETUP DISABLE MODEL WV-CW480 SERIES CAMERA BACK-FOCUS SPECIAL LANGUAGE SETUP ENABLE **CAMERA SETUP** 1/2 CAMERA ID SHUTTER ON(HIGH) SENS UP SYNC WHITE BAL ATW1 MOTION DET HIGH RESOLUTION HIGH BW MODE **CAMERA SETUP** 2/2 PRIVACY ZONE EL-ZOOM UPSIDE-DOWN STABILIZER LENS PANASONIC...
  • Page 28 6. To exit from the SETUP menu and display images from the camera, move the cursor onto "END" and press the [SET] button. Notes: • To prevent erroneous operations, the "DISABLE" indication will always be displayed when the top page is displayed from the camera. To operate the SETUP menu, switch the "DIS- ABLE"...

  • Page 29: Setting Procedures

    Setting Procedures First, select a language for menu display and camera ID display. Language Setup (LANGUAGE SETUP) 1. Select LANGUAGE on the top menu and press the [SET] button. → The LANGUAGE SETUP menu opens. 2. Select a language. The default setting is English.
  • Page 30 • To erase all characters of the camera ID, select RESET and press the [SET] button. Note: For Chinese language, up to 8 characters can be entered. 4. To specify the ID display position: 1. Select POSI and press the [SET] button. →...
  • Page 31 2-2. ALC Mode with SUPER-D3 OFF 1. Move the cursor to ALC on the CAMERA SETUP menu and select OFF for SUPER-D3 on the ALC CONT menu. → MASK SET↓ appears on the ALC CONT menu. 2. Select MASK SET and press the [SET] but- ton.
  • Page 32 Notes: • Only OFF is available when SUPER-D3 is set to ON. • When a faster speed is selected for the electronic shutter, the picture will generally become darker, and sometimes a smear (vertical stripes caused by bright objects) may appear. 4.
  • Page 33 6. Synchronization Setting (SYNC) 1. Select a sync mode. VD2: Multiplexed vertical drive, highest priority LL: Line-Lock, follows the phase of supplied AC power, 2nd priority INT: Internal sync, lowest priority Notes: • Selection is not available when VD2 is added to the camera. Selection from LL is avail- able when the respective sync is added.
  • Page 34 AWC Setting 1. Select AWC and press the [LEFT] button. → AWC will change to AWC → PUSH SW. 2. Press the [SET] button. → PUSH SW will be highlighted while the AWC setting is performed. Note: If the white balance is not set, PUSH SW is being highlighted. 3 .
  • Page 35 DISPLAY MODE screen. Notes: • In systems other than Panasonic, select OFF for MOTION DET to prevent system devices from confusing time-code signal with alarm signal. • Set MASK SET over the areas where leaves or curtains etc. are swaying.
  • Page 36 About MODE2 of Motion Detection • The camera will detect a scene change in the following cases. When the lens is fully sprayed or covered with a cloth, lid, or the like When the camera direction is suddenly changed • The camera will not detect a scene change in the following cases. When a cloth with patterns covers the lens and it sways in the wind When some portions in the screen are not veiled When the screens are similar in scene patterns although the camera direction has...
  • Page 37 → When AUTO1 or AUTO2 is selected, LEVEL and DURATION TIME appear. 3. Select a threshold LEVEL to switch between the colour and black-and-white mode. The default setting is HIGH. HIGH: Switches the mode at approx. 5 lx illu- mination. LOW: Switches the mode at approx.
  • Page 38 5. Select →PUSH SW for SCALE and press the [SET] button. → Zone scale adjustment becomes available. 6. Adjust the zone scale using the [LEFT], [RIGHT], [UP], or [DOWN] button. 7. To apply the settings, move the cursor to SET and press the [SET] button. →...
  • Page 39 • Image stabilization may not function where there is excessive camera movement or when the scene is low light or low contrast objects. 16. LENS Select PANASONIC. 17. Back-focus Setting (BACK-FOCUS SETUP) Perform adjustment of the back-focus (flange- back: the gap between the lens and focal plane) remotely on this menu using a system controller.
  • Page 40 4. Select a mode for C/L ↔ B/W. The default setting is AUTO. AUTO: Adjusts the back-focus automatically every time the camera switches the mode between colour and black-and-white. AUTO is usable only when OFF, X2 AUTO, or X2 FIX is selected for SENS UP. PRESET: Adjusts the back-focus to the positions for colour mode and black-and-white mode that are preset by performing step 2 (automatic) or step 3 (manual) under the respective light conditions.
  • Page 41 18-2. Aperture Gain Setting (AP GAIN) Move the "I" cursor to adjust the aperture gain level. Lower the level when moire (a kind of noise, optical interference) appears on the screen as part of minute crosshatch pattern, etc. 18-3. Pedestal Level Setting (PEDESTAL) Move the "I"...
  • Page 42 18-5. To reset to the default settings (CAMERA RESET) 1. Select CAMERA RESET. → The PUSH SW is highlighted. 2. While holding down the [LEFT] and [RIGHT] buttons, press the [SET] button for 2 seconds or more. → The camera will return to the default settings. Note: PIX OFF setting cannot be initialized.

  • Page 43: Troubleshooting

    (WV-CW484F) • Is 220 V to 240 V AC power sup- ply connect to the power supply terminal? (WV-CW480S) • Is the video output cable connect- ed to the video connector of the monitor? →...

  • Page 44: Specifications

    Specifications <WV-CW484F General specifications> Power source and power consumption: Ambient temperature: Ambient humidity: Water resistance: Dimensions: Weight: <WV-CW480S General specifications> Power source and power consumption: Ambient temperature: Ambient humidity: Water resistance: Dimensions: Weight: Mounting bracket: * Heater Unit WV-CW4H (option) is not available with 12 V DC power supply.
  • Page 45 ATW1, ATW2, or AWC MODE1, MODE2, or OFF HIGH or LOW NORMAL or HIGH AUTO1, AUTO2, ON, or OFF ON (1/2), or OFF ON or OFF ON or OFF ON or OFF Panasonic or OTHER ABF, MANUAL, AUTO/PRESET/FIX Chroma, Aperture, Pedestal, Pixel Compensation...

  • Page 46: Standard Accessories

    Operating Instructions (This document) ... 1 pc. The following parts are used during installation procedures. Mounting Bracket (For WV-CW480S) ... 1 pc. Screws for mounting bracket (M4 x 8) (For WV-CW480S) ... 4 pcs. Camera attachment ... 1 pc. Bit for tamperproof screw ... 1 pc.
  • Page 48 Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://panasonic.net Printed in Japan Gedruckt in Japan Imprimé au Japon © 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. Impreso en Japón Stampato in Giappone ç‡Ô˜‡Ú‡ÌÓ ‚ üÔÓÌËË NM1106-3027 3TR004601DAA...

This manual is also suitable for:

Wv-cw484f

Table of Contents