Panasonic VL-WD812EX Installation Manual

Installation Guide
Wireless Sensor Camera
(Wireless sensor camera
is described as "camera"
in this guide.)
VL-WD812EX
Model No.
Note to the installer
■ Please read this guide carefully, and install the product safely and correctly by following the
instructions. Carefully read the information found in the section titled "For your safety" in
particular.
■ Only use attachments/accessories specified by the manufacturer.
■ The installation shall be carried out in accordance with all applicable installation rules.
■ Panasonic assumes no responsibility for injuries or property damage resulting from failures
arising out of improper installation or operation inconsistent with this guide. Additionally, any
resulting malfunction will not be covered under the warranty.
■ After installation, make sure to leave this guide with the customer.
Supplied accessories for installation
□ Wall mount bracket x 1 □ Screw x 4 □ Sensor range cap
x 1 set of 4
(4 mm × 20 mm)
Used to attach the
wall mount bracket
to the camera Used for the heat
sensor
□ Cap removement tool x 1 □ Screw cover x 4 □ Washer x 1
Used to remove the Used when
sensor range caps attaching the safety
from the camera wire to the wall
Power supply unit and related items
□ Power supply unit x 1 □ Cable binder x 2
(Part No. VL-PS240)
Important:
● You will need the following additional items to install and configure the camera.
[Locally procured]
– Screws (for wall mount bracket: × 4, for safety wire: × 1):
4 mm
Prepare the screws ( the drawing on the right) according to the
material, structure, strength and other factors of the mounting area
and the total weight of objects to be mounted.
– Power cables (AC/DC cables), wires (for an external sensor connection):
Prepare cables and wires of the appropriate specification. ( "Wire type and length")
● Retain the cap removement tool and any unused sensor range caps as they may be needed
when making adjustments in the future.
Note:
● The illustrations in the supplied manual(s) may vary slightly from the actual product.
For your safety
To prevent severe injury and loss of life/property, read this section carefully before using the
product to ensure proper and safe operation of your product.
WARNING
Preventing fire, electric shock and short circuits
● Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may
cause fire, electric shock, injury, or damage to the product. Consult the dealer.
● Electrical connection work should be performed by certified personnel only. Certification
is required for performing electrical connection work. Consult your dealer.
● Use only the specified power supply unit.
● Do not attempt to disassemble or modify this product. Contact an authorised service
centre for repairs.
● Never install wiring during a lightning storm.
● Do not connect non-specified devices.
● Do not connect a power cable to a terminal that is not specified in this guide.
● When opening holes in walls for installation or wiring, or when securing the power
cable, make sure you do not damage existing wiring and ductwork.
● Do not make any wiring connections when the power supply is turned on.
● Do not use the supplied power supply unit for outdoor installations (it is for indoor use
only).
● Do not install the power supply unit in the following places:
- Places where the power supply unit may be splashed with water or chemicals.
- Places where there is a high concentration of dust, or high humidity.
● Do not leave the power cable exposed outdoors.
● Do not perform any actions (such as fabricating, twisting, stretching, bundling, forcibly
bending, damaging, altering, exposing to heat sources, or placing heavy objects on the
power cable) that may damage the power cable. Using the product with a damaged
power cable may cause electric shock, short circuits, or fire. Contact an authorised
service centre for repairs.
● Mount the wall mount bracket so that the " UP" mark faces up. Caulk the mounting
face of the wall mount bracket, except for the bottom part of the bracket, with a water-
resistant sealant, making sure to fill in any gaps. If the bracket is mounted upside down
or if the bracket is not properly waterproofed, water may enter, which may result in fire
or electric shock.
Preventing accidents and injuries
● Do not install or use the product in an inflammable atmosphere. Failure to observe this
may cause an explosion resulting in injury.
● Do not install or use the product in health care facilities if any regulations posted in
the area instruct you not to do so. Hospitals or health care facilities may be using
equipment that could be sensitive to external RF (radio frequency) energy.
● Do not install or use this product near automatically controlled devices such as
automatic doors and fire alarms. Radio waves emitted from this product may cause
such devices to malfunction, resulting in an accident.
● Do not mount the bracket in an unstable location, in a location subject to frequent
vibration, on a ceiling, or on a weak wall. (Do not mount on plaster board, concrete
blocks, wooden materials exposed to the outdoors, walls with very rough surfaces, or
surfaces that are narrower than the width of the wall mount bracket.) There is a risk of
injury if the product falls, or of fire or electric shock if water enters the product.
● Keep the sensor range caps out of the reach of children. There is a risk of swallowing.
In the event they are swallowed, seek medical advice immediately.
CAUTION
Preventing electric shock
● If the wiring is underground, do not make any connections underground.
● If the wiring is underground, make sure the power cable and other wiring is properly
waterproofed by running the cables through a conduit.
Preventing injury
● The safety wire must be used when mounting the product. There is a risk of injury if the
product falls.
Precautions for installation
Before installation
The main monitor station (called "main monitor") and the camera use radio waves to communicate
with each other. (The product operates in the frequency range of 1.88 GHz to 1.90 GHz, and the
RF transmission power is 250 mW (max.).) Read the following and install the product in an appro-
priate location.
Main monitor Operation distance: up to 100 m
(with no obstacles)
Communication between the main monitor and the camera
● The maximum communication distance between the main monitor and the camera (up to
100 m) may be shortened when the product is used in places where there are the following
obstacles between the main monitor and the camera.
● Metal doors or metal shutters.
● Heat insulation including aluminium foil.
● Concrete walls or walls made of galvanized iron sheet.
● If the wireless monitor station (called "sub monitor") is being used in a different
building, or a different part of the house, i.e. a different floor to the where the main
monitor has been installed.
● Many walls
● Double insulated glass windows
If there are the above obstacles, images displayed on the main monitor may be distorted
or delayed, audio may cut out, and the product may not be usable. In this case, the cam-
era's indicator lamp lights or flashes red. (
"Camera signal status" below.)
● You can rectify these problems by using an optional DECT Repeater VL-FKD2EX to
relay the signal from the main monitor. ( Operating Instructions of the Video Intercom
System)
Confirming the signal condition at the installation location
If your Video Intercom System includes a sub monitor, it can be used to easily check the sig-
nal status. (If there is no sub monitor, use a camera.)
■ Using the sub monitor to confirm Sub monitor signal condition
Out of
By taking the sub monitor to the installa- Weak
Strong
range
tion site, you can confirm the signal status
on the sub monitor's screen.
Install within this range
Camera signal status
■ Using the camera to confirm
Out of
Temporarily connect the camera and the
Strong Weak range
power supply unit to turn on the camera,
Lit Lit Flashing
and then register it to the main monitor. Lit red
green orange red
Later, you can take the camera to the
installation site and confirm the signal sta-
Install within this range
tus using the camera's indicator lamp.
Do not install in these locations
■ To prevent deformation, discolouration, malfunction, operational failure
● In direct sunlight or directly under an ● Areas subject to extreme temperature
outdoor light (even if the surrounding variation (which can lead to condensation)
areas are within the operational ● Near ocean coasts, where sea breezes
temperature range, portions of the product will contact the product directly, or near
may become hot) sulphuric hot springs (exposure to salt can
● Areas subject to frequent vibration, shock, reduce the product's life expectancy)
or impact ● Near TVs, radios, computers, air
● Near fire, heating devices, or magnetic conditioners, boiler control panels with
fields (such as near magnets) intercom, or home security equipment
● Near heating or cooling systems, (these may cause noise)
including outdoor equipment such as air ● Near satellite broadcast receiving devices,
conditioning unit compressors including tuners, TVs with built-in satellite
● In greasy or moist locations tuners, and recorders (broadcast images
● Near devices that emit radio waves, such may be distorted)
as mobile phones ● Areas where hydrogen sulphide, ammonia,
dust, or noxious gases are present
■ Incorrect detections may occur in the following locations
● Areas where people approach from ● On high-traffic streets
directly in front of the camera, such as (passing cars may cause detections even
narrow walkways if they are more than 5 m away)
Difficult to detect
Camera
● In areas subject to breezes from fans, air
conditioning unit compressors, or hot water
● In areas where objects move naturally,
heaters, or areas affected by car exhaust
such as where the wind blows trees or
(severe temperature variations may cause
hanging laundry (temperature variation
incorrect detections)
and motion may cause incorrect
detections)
● In areas with strong winds (wind can vibrate the camera, causing incorrect motion detection.)
● Where reflective objects are in front of the camera and can interfere with the heat
detection, such as glass.
● In areas where brightness changes easily (for example where shadows form in the
afternoon and where lights turn on at night)
● In areas where backlight occurs (faces in the dark may not be able to be identified.)
● If a strong light is shining on the camera, the visitor's face may not be distinguishable.
Do not place the camera in the following locations.
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the camera.
Privacy and rights of portrait
When installing or using the camera, please take into consideration the rights of others with regard
to privacy.
● It is generally said that "privacy" means the ability of an individual or group to stop information
about themselves from becoming known to people other than those whom they choose to give
the information. "Rights of portrait" means the right to be safe from having your own image taken
and used indiscriminately without consent.
About the sensors
(motion detection sensor and heat sensor)
The camera has 2 sensors: the motion detection sensor and the heat sensor.
Please read the following information about the camera's motion detection sensor and heat sensor
before deciding where to mount the camera.
Sensor characteristics and detection range
Motion detection sensor Motion detection Heat sensor Motion detection
The camera detects changes in the The camera detects temperature
images being displayed. differences of objects in the images
being displayed.
● The camera detects changes in the
Detection
brightness levels of moving objects. ● The heat sensor uses infrared rays to
method
detect temperature differences within
its range that are emitted naturally by
people, animals, etc.
Easily detects movement in the day- Easily detects when there is a big dif-
ference between the temperatures of
time or when it is bright.
objects and the surrounding environ-
● Movement may be incorrectly
ment, such as in winter or late at night.
detected when the moving object
and the background have a similar ● The sensor cannot easily detect
Main
colour. when there is no difference between
character-
● Movement may be incorrectly the temperatures of objects and the
istics
detected when there are sudden surrounding environment, such as in
changes to the overall brightness summer or during the daytime.
levels such as when external lights ● If the camera is mounted facing
are used. a road, the sensor may detect
incorrectly due to interference caused
by the heat from passing cars.
Entire viewed image Part of viewed image (grey area)
Detection
range
● The detection range can be reduced. ● The detection range can be changed.
"Changing the detection
"Changing the angle of the
range of the motion detection sen- heat sensor"
sor" on the reverse side
"Using the sensor range caps" on
the reverse side
It is difficult to This is the same for the
motion detection sensor
detect movement
and the heat sensor.
directly towards the
front of the camera.
It is easy to detect
movement sideways in
Easy to
front of the camera.
detect/
Difficult
to detect
Detection range
Camera
● The motion detection sensor and heat sensor are not designed to be used in situations that
require high reliability. We do not recommend use of the motion detection sensor and heat
sensor in these situations.
● Panasonic takes no responsibility for any injury or damages caused by use of the motion
detection sensor and heat sensor.
Sensor operating range
In the default settings, the motion detection sensor and heat sensor operate in the following way
depending on changes to the brightness levels.
Daytime or when it is bright At night or when it is dark
Motion detection sensor
Heat sensor
● The brightness level is automatically determined by the camera when viewing images.
A timer can be configured to switch the modes between day and night modes at specified times.
( [Day and night switch] setting in the Operating Instructions of the Video Intercom System)
● The settings can be configured to match the installation environment by only operating the
motion detection sensor and heat sensor at certain times, for example only during the day
or only at night. ( [Heat sensor detection] and [Motion detection] settings in the Operating
Instructions of the Video Intercom System)
Installation example A
(detect visitors)
To detect visitors at the entrance (gate) without detecting cars in the street
Ideal example Poor example
Street Street
Distance:
approx. 3 m
It is easy to It is difficult to
detect visitors detect visitors
moving side-
moving toward
ways in front of
the camera.
Camera
the camera.
Camera
Entrance Entrance
Visible image: Visible image:
Visitors moving sideways are visible, and
Cars in the street are more likely to cause
cars in the street are less likely to cause
incorrect detections.
incorrect detections.
If you want to detect visitors as well as see the view directly in
front of the camera, use a commercially available external sensor.
Installation example (using a commercially available external sensor)
You can connect commercially available external sensors to the external input terminal.
● In this case you must use the main monitor to change the camera's [Sensor selection] setting.
( Operating Instructions of the Video Intercom System)
● Refer to "About the external input terminal" ( above right) and connect the external sensor
properly according to its specifications.
Visible image:
Street
Visitors pass in
front of the exter-
nal sensor and are
By configuring the [Sensor selection]
easy to detect even
setting so that only the external sensor
if they approach
is used, cars visible by the camera are
the camera.
less likely to be incorrectly detected.
Camera
Entrance
Commercially available external sensor
Installation example B
(detect people entering a garage)
To detect people entering a garage without detecting cars in the street
Ideal example Poor example
Street
Street
Camera
It is difficult to
It is easy to
detect people
detect people
moving toward
moving side-
the camera.
ways in front of
the camera.
Camera
● To prevent faces from being obscured by tall
vehicles, adjust the installation location and
angle of the camera.
Visible image: Visible image:
People moving sideways are visible, and
Cars in the street are more likely to cause
cars in the street are less likely to cause
incorrect detections.
incorrect detections.
If you want to detect people as well as see the view directly in
front of the camera, use a commercially available external sensor.
Installation example (using a commercially available external sensor)
You can connect commercially available external sensors to the external input terminal.
● In this case you must use the main monitor to change the camera's [Sensor selection] setting.
( Operating Instructions of the Video Intercom System)
● Refer to "About the external input terminal" ( above right) and connect the external sensor
properly according to its specifications.
Visible image:
Street
By configuring the [Sensor selection]
People pass in front
setting so that only the external sensor
of the external sen-
is used, cars visible by the camera are
sor and are easy to
less likely to be incorrectly detected.
detect even if they
approach straight to
Camera
Commercially available external sensor
the camera.
About the external input terminal
(for an external sensor connection)
Choose an external sensor that is compatible with the specifications of the external input terminal.
● After connection, use the main monitor to select the contact type ([Make contact] or
[Break contact]) that matches the device. ( [External sensor] setting in the Operating
Instructions of the Video Intercom System)
External input terminal
Cover
Do not connect
Bracket cover anything to this
Lift the tab
terminal.
to open the
cover
■ External input terminal specifications
Detection can occur when the terminal is closed or opened.
● Voltage when open: approx. 9 V
● Current when closed: approx. 6 mA (detection occurs after 0.1 s of continual close/open)
■ Wire type and length ( "Wire type and length" below)
About installation
● Install so that the power shutoff device is located near the power supply unit and is easily
accessible.
● Use 600 V AC or higher insulated wiring.
Wire type and length
Wire type *1
Wiring run
Diameter Length (Max.)
φ 0.65 mm 22 AWG 50 m
Camera -
A
Power supply unit
φ 1.0 mm 18 AWG 100 m
φ 1.2 mm 17 AWG
Power supply unit -
No requirement
B
AC power source
φ 2.0 mm 12 AWG
φ 0.5 mm 24 AWG According to specification of
Camera -
C connected device. Must be no
External sensor
φ 0.8 mm 20 AWG longer than 20 m.
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
Outer diameter A,C: φ 8 mm (Max.)
● A certified power supply wiring has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A certified power
supply wiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC
60227 shall be used.
Installation overview
Before installing the camera on the wall, be sure to register the camera to the main monitor
nearby so that you will be able to check the signal strength at the installation point.
1
Temporarily connect the camera and the power supply unit to turn on the camera, and
then register the camera to the main monitor. ( below)
2
Check that the signal can reach from the camera's installation location.
( "Confirming the signal condition at the installation location")
3
Install the power supply unit. ( reverse side)
4
Install the camera. ( reverse side)
Temporarily connecting to the power supply unit
Temporarily connecting is necessary to register the camera to the main monitor and to confirm
the condition of the signal at the installation location.
Refer to "Installing the power supply unit and camera" on the reverse side for information
about connecting a cable from the camera to the power supply unit.
Cable covers
● Make sure you turn off the power
at the breaker before connecting
a power cable.
● Make sure you attach the cable
covers after you make the
temporary connection.
Screws
Registering to the main monitor
Temporarily connect the camera to turn it on, and then register it to the main monitor as
explained below.
● You cannot register more than one camera at a time. Register each camera one at a time.
● The operations described here are based on the VL-SWD501EX series main monitor. See
the Operating Instructions of the Video Intercom System for more information.
1
Main monitor operation
→
From the top menu of the main monitor, touch
→ [Register/Cancel] → [Register] → [Camera] → the camera number of the camera
to be registered.
● After this, use the camera and complete the following steps within about 5 minutes.
2
Camera operation
(Rear of camera)
Perform the following registra-
tion procedure while the cam-
era is turned on.
2-1 Peel open the register button
cover (A) and use the thin
B
end of the cap removement
tool (accessory) to press and
A
hold the register button (B) for
about 3 seconds.
2-2 Make sure to firmly close the
register button cover.
C
● The camera's indicator lamp (C)
flashes in green during registration.
When registration is complete,
a beep sounds and the indicator
lamp lights in green.
3
To end the operation, press
on the main monitor.