1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Network Router
  5. dgs-8000 SERIES
  6. Hardware installation manual

D-Link dgs-8000 SERIES Hardware Installation Manual

Hide thumbs Also See for dgs-8000 SERIES:
Table of Contents

Advertisement

Quick Links

Download this manual
DGS-8000
Hardware Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for D-Link dgs-8000 SERIES

Summary of Contents for D-Link dgs-8000 SERIES

  • Page 1 DGS-8000 Hardware Installation Guide...

  • Page 2: Contents

    D-Link Corporation reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of D-Link Corporation is prohibited. Exemption statement This document is provided “as is”.

  • Page 3: Document Structure

    Documentation CD-ROM: The documentation of D-Link Corporation switches is stored in the CD-ROM package, which is provided to you together with the product you purchase. The CD-ROM is updated frequently, and may be more current than the printed documents.

  • Page 4: Documentation Conventions

    D-Link Corporation provides excellent technical support services for all our products. You can obtain the technical assistance you need through any of the following channels: Technical Assistance  D-Link Corporation Website, On D-Link Corporation Website, you can obtain the latest technical information, reasons of common faults, problem analysis, product application solution and software upgrading information.

  • Page 5: Table Of Contents

    Contents Preface................................ii Scope ................................ii Document Structure ............................. ii Related Documents ............................ii Contents ............................... 1 Product Overview........................... 1 Product Overview..........................1 Technical Specifications........................1 Technical Specifications ....................1 1.2.1 DGS-8000 Switch System ......................4 Product Appearance......................4 1.3.1 Front panel ........................6 1.3.2 Back panel........................9 1.3.3 Power system.........................
  • Page 6 Unpacking Requirements......................40 Goods Checklist ......................40 2.5.1 Switch Installation ..........................41 Installation Flow ..........................42 Installation Verification ........................42 Cabinet Installation ........................43 Precautions ........................43 3.3.1 Simple Installation Steps ....................43 3.3.2 Mounting into the Cabinet......................43 Precautions ........................43 3.4.1 Simple Installation Steps ....................44 3.4.2 Installing and Removing Fan Tray ....................44 Installing and Removing the Plastic Dust Cap of a Switching Power Supply......45 Installing and Removing the Air Filter of a System Switching Power Supply....45 3.6.1...
  • Page 7 Checking after Power-on (Recommended)..............55 4.2.2 Maintenance............................56 DGS-8000 Monitoring .........................56 DGS-8000 Hardware Maintenance.....................56 Single-board Maintenance .....................56 5.2.1 Ventilation System Maintenance ..................56 5.2.2 Power Supply Maintenance ...................57 5.2.3 Remote Maintenance .....................57 5.2.4 Module Fuse Specification .....................57 5.2.5 Troubleshooting ........................... 58 General Installation Troubleshooting Flow..................58 Common Troubleshooting Procedures ..................59 AppendixA Connectors and Connection Media ..................

  • Page 8: Contents

    DGS-8000 series Ethernet switches support the dual management boards and power supply redundancy, providing two kinds of hosts with 10 vertical slots and 6 horizontal slots respectively: DGS-8010 and DGS-8006.
  • Page 9 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Power Supported(must be the same type) supply redundancy 8006-FAN 8010-FAN Environment GB9254-1998 CLASS A，FCC CLASS A Safety GB4943-2001 regulation 0 to 50°C Operating temperature -40 to 70°C Storage temperature 10% to 90% RH...
  • Page 10 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview The 100Base-FX/1000Base-X SFP fiber ports of partial DGS-8000’s linecards and the corresponding 10/100/1000Base-T copper ports are fiber/copper combo ports. That is, only one port (fiber port or copper port) can be used at the same time. By default, the copper port has the priority to be used.

  • Page 11: Dgs-8000 Switch System

    Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide DGS-8000 Switch System Product Appearance 1.3.1 Appearance of DGS-8006 1.3.1.1 DGS-8006 hardware system consists of chassis, power supply system, system modules and heat dissipation system. Power supply system provides two slots for the power and supports 1+1 power redundancy.
  • Page 12 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Appearance of DGS-8010 1.3.1.2 DGS-8010 hardware system consists of chassis, power supply system, system modules and heat dissipation system. Power supply system provides two slots for the power and supports 1+1 power redundancy.

  • Page 13: Front Panel

    Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Figure 1-2 Appearance of DGS-8010 Front panel 1.3.2 Front panel of DGS-8006 1.3.2.1 Figure 1-3 shows the schematic diagram of DGS-8006 front panel.
  • Page 14 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Figure 1-3 ○ 1 Slots for service modules; ○ 2 Slots for management modules; ○ 3 Wiring rack; ○ 4 System power module installation location; ○ 5 Anti-static wrist strap hole;...
  • Page 15 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Figure 1-4 ○ 1 Slots for service modules; ○ 2 Slots for service modules; ○ 3 Slots for management modules; ○ 4 Fan tray; ○ 5 System power module installation location;...

  • Page 16: Back Panel

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview ○ 9 Wiring rack; ⑩ Dust prevention air-inlet plastic panel Before moving or transporting the DGS-8010 chassis, all management modules、service modules and the power modules must be unplugged from the chassis. Moving/Transporting the DGS-8010 device with the management Warning modules or service modules or power modules inserted is prohibited.
  • Page 17 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide ○ 6 Fan tray; ○ 7 Fan tray handle; ○ 8 Captive screws on the fan tray; Back panel of DGS-8010 1.3.3.2 Figure 1-6 shows the schematic diagram of DGS-8010 back panel.

  • Page 18: Power System

    Power system 1.3.4 DGS-8000 series Ethernet switch uses the AC power input. Currently the 8000-1400AC and 8000-2000AC power modules are provided for this switch. The two power modules support the power management. The management engine of DGS-8000 can read the power information and realize the flexible and intelligent management for the whole switch’s power...
  • Page 19 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Figure 1-7 DGS-8006 heat dissipation system Note: The structure of host management module and service module is designed with air inlet on right side, and air outlet at back. And the power module is designed with air inlet at front, and air outlet at back.

  • Page 20: Modules

    Introduction 1.4.1.1 As the management engine module of the DGS-8000 series Ethernet switch, the 8000-CM1 module provides management and switching functions for the switch. The 8000-CM1 module provides a Console port, a 10/100/1000M MGMT port, a USB port, an SD card port,...
  • Page 21 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Figure 1-9 8000-CM1 appearance The 8000-CM1 module provides five external ports:  Universal Serial Bus (USB) port: This port can be connected to a USB storage that is used to store logs, host versions, alarms and other diagnosis information, facilitating online upgrade of switch software and saving of log information.
  • Page 22 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Solid Green The initialization of the module is complete, and switching can be performed normally. Primary/Seconda Primary The module is a secondary ry MGMT engine management engine module. Solid Green module primary management engine module.

  • Page 23: 8000-24Sc2Xg-E Module

    Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Technical Specifications 1.4.1.3 Table 1-4 8000-CM1 technical specifications Product Model 8000-CM1 800MHz BOOTROM Flash Memory 512MB SDRAM One Console port, one 10/100/1000M MGMT port, one USB port, External ports one SD card port, and one Reset button Power consumption <91W...
  • Page 24 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Figure 1-10 8000-24SC2XG-E appearance LEDs on the Module Panel 1.4.2.2 The 8000-24SC2XG-E module provides LEDs indicating system states. The Status LED indicates the operating status of a board itself, and each port provides a Link/ACT LED to indicate the operating status of the port itself.
  • Page 25 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Technical Specifications 1.4.2.3 Table 1-6 8000-24SC2XG-E technical specifications Product Model 8000-24SC2XG-E Ports Two 10G XFP ports, 12 pure SFP ports, and 12 fiber/copper combo ports Fiber Transceiver Supported SFP Transceivers: supported 1.

  • Page 26: 8000-24Sc-E Module

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview The first 12 ports of the 8000-24SC2XG-E module are fiber/copper combo ports. That is, each SFP port corresponds to a combo 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable.
  • Page 27 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide port. port Link/ACT There is no link Up. Solid Green The link is Up at 1000Mbps. Solid Yellow The link is Up at 100Mbps. Blinking There is data received or sent on the port.

  • Page 28: 8000-48Tc-E Module

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Operating 10% to 90% RH humidity Weight 3.2kg (net) Dimensions (L x 436 x 346 x 45 mm W x H) The first 12 ports of the 8000-24SC-E module are fiber/copper combo ports.
  • Page 29 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Solid Green The initialization of the module is complete, and switching can be performed normally. RJ-45 port Link/ACT There is no link Up. Solid Green The link is Up at 1000Mbps.

  • Page 30: 8000-48Pc-E Module

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview GB9254-1998 Class A; FCC Class A Safety GB4943-2001 Operating temperature 0 to 50°C Storage temperature -40 to 70°C Operating humidity 10% to 90% RH Weight 3.6kg (net) Dimensions (L x W x...
  • Page 31 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide LEDs on the Module Panel 1.4.5.2 The 8000-48PC-E module provides LEDs indicating system states. The Status LED indicates the operating status of a board itself, and each port provides a Link/ACT LED to indicate the operating status of the port itself.
  • Page 32 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Technical Specifications 1.4.5.3 Table 12 8000-48PC-E technical specifications Product 8000-48PC-E Model Ports 44 RJ-45 ports for 10/100/1000BASE-T, four fiber/copper combo ports. A maximum of 48 PoE ports are supported. Fiber Supported SFP Transceivers: Transceiver 1.

  • Page 33: 8000-24Tc-E Module

    Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide The last four ports of the 8000-48PC-E module are fiber/copper combo ports. That each port corresponds combo 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of 10/100/1000BASE-T copper ports is effective only when auto-negotiation is enabled.
  • Page 34 DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Solid Green The link is Up at 1000Mbps. Solid Yellow The link is Up at 10Mbps or 100Mbps. Blinking There is data received or sent on the port. port Link/ACT There is no link Up.

  • Page 35: 8000-4Xg-E Module

    Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Weight 3.2kg (net) Dimensions (L x W x 436 x 346 x 45 mm The last 12 ports of the 8000-24TC-E module are fiber/copper combo ports. That each port corresponds combo 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable.

  • Page 36: 8010/8006-Fan Module

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Solid Green The link is Up at 10Gbps. Blinking There is data received or sent on the port. Technical Specifications 1.4.7.3 Table 16 8000-4XG-E technical specifications Product 8000-4XG-E Model Ports Four 10G XFP ports...
  • Page 37 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Figure 16 8010-FAN appearance Figure 17 8006-FAN appearance LEDs on the Module Panel 1.4.8.2 Table 1-17 LEDs on the front panel Identifier Status Meaning Power Power The module has no input power supply supply LED or the input power supply is abnormal.

  • Page 38: 8000-1400Ac/8000-2000Ac Power Supply Module

    DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview Highest 5400RPM 5400RPM rotation speed Power 240W 160W consumption Weight 6.0kg (net) 4.0kg (net) Dimensions (L 431.6 x 396.2 x 44 mm 312.3 x 298 x 64.4 mm x W x H) 8000-1400AC/8000-2000AC Power 1.4.9...
  • Page 39 Chapter 1 Product Overview DGS-8000 Series Hardware Installation Guide Maximum 90-264V~; 47-63Hz 90-264V~; 47-63Hz voltage range 90-176V~ Power: 530W 90-176V~ Power: 1080W Maximum ouput power 176-264V~ Power: 1400W 176-264V~ Power: 2000W Weight 4.9kg (net) 5.0kg (net) Power cord The front panel provides a 3-core power supply interface to connect a standard 16A power cord.

  • Page 40: Preparation For Installation

    DGS-8000 Series Hardware Installation Guide Chapter 2 Preparation before Installation Preparation for Installation Safety Suggestions To avoid bodily injury and equipment damage, please carefully read the safety suggestions before you install DGS-8000. Note: The following safety suggestions do not cover all possible dangers.

  • Page 41: Static Discharge Damage Prevention

    Chapter 2 Preparation before Installation DGS-8000 Series Hardware Installation Guide  Please carefully check for any potential danger in the working area, for example, ungrounded power supply, unreliable grounding of the power supply and damp/wet ground or floor.  Find out the location of the emergency power supply switch in the room before installation.

  • Page 42: Installation Site Requirements

    DGS-8000 Series Hardware Installation Guide Chapter 2 Preparation before Installation Laser Safety 2.1.5 Among the modules supported by DGS-8000, there are a great number of optical modules that are Class I laser products. Therefore, pay attention to the following during your use of this product: ...
  • Page 43 Chapter 2 Preparation before Installation DGS-8000 Series Hardware Installation Guide Figure 2-1 Ventilation of DGS-8010 Figure 2-2 Ventilation of DGS-8006...

  • Page 44: Temperature And Humidity Requirements

    DGS-8000 Series Hardware Installation Guide Chapter 2 Preparation before Installation Temperature and Humidity 2.2.3 Requirements To ensure the normal operation and a prolonged use life of the DGS-8000, you must maintain an appropriate temperature and humidity in the equipment room.

  • Page 45: System Grounding Requirements

    Chapter 2 Preparation before Installation DGS-8000 Series Hardware Installation Guide Average (mg/m Maximum (mg/m Sulfured hydrogen 0.006 0.03 Nitrogen dioxide 0.04 0.15 Ammonia 0.05 0.15 Chlorine 0.01 Power Requirements 2.2.5 When the DGS-8000 uses the AC power supply: 8000-1400AC: AC input voltage: 90-264V~, 47~63Hz...

  • Page 46: Emc Ground

    DGS-8000 Series Hardware Installation Guide Chapter 2 Preparation before Installation EMC Ground 2.3.3 The ground required for EMC design includes shielding ground, filter ground, noise and interference suppression, and level reference. All the above constitute the comprehensive grounding requirements. The grounding resistance should be less than 1Ω. Two grouding poles are reserved at the back,left and right sides respectively.

  • Page 47: Unpacking Requirements

    Fiber optic cleaning Air-laid paper, fiber end microscope tools Meter Multimeter, Errormeter, Optic-power meter Note: DGS-8000 series is not shipped with a tool kit. You need to prepare a tool kit by yourself. Unpacking Requirements Goods Checklist 2.5.1 1. DGS-8000 chassis carton ...

  • Page 48: Switch Installation

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation Switch Installation DGS-8000 series Ethernet switch must be used and fixed in the room. Note: Before you install the DGS-8000, make sure you have carefully read Chapter 2 and this chapter.

  • Page 49: Installation Flow

    Chapter 3 Switch Installation DGS-8000 Series Hardware Installation Guide Installation Flow Installation Verification The DGS-8000 is complicated equipment, so you must carefully plan and arrange the installation location, networking mode, power supply, and wiring before installation. Verify the following before installation: ...

  • Page 50: Cabinet Installation

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation  The selected power supply meets the system power. Cabinet Installation Precautions 3.3.1 When you install the cabinet, pay attention to the following:  All expansion bolts for fastening the cabinet base to the ground should be installed and tightened in sequence from bottom up (large plain washer, spring washer, and nut), and the installation holes on the base and the expansion bolts should be well aligned.

  • Page 51: Installing And Removing Fan Tray

    Chapter 3 Switch Installation DGS-8000 Series Hardware Installation Guide  Remove any obstacle in the frame and the surrounding environment.  Prepare the equipment and move it to the place near the cabinet where you can handle it easily. Simple Installation Steps 3.4.2...

  • Page 52: Installing And Removing The Plastic Dust Cap Of A Switching Power Supply

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation Installing and Removing the Plastic Dust Cap of a Switching Power Supply Plastic dust caps for the system switching power supply module, host management module, and service module on the DGS-8000 need to be configured.

  • Page 53: Installing And Removing The Air Filters Of The Host Management Module And Service

    Chapter 3 Switch Installation DGS-8000 Series Hardware Installation Guide Plastic dust cap of the switching power supply ① Buckle on the plastic dust cap of the switching power supply ② Installing and Removing the Air 3.6.2 Filters of the Host Management...
  • Page 54 DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation (1) Insert the air filter along the guide rail and tighten the captive screws on the air filter. (2) Install the plastic dust cap before the air filter by pressing firmly the two buttons of the plastic dust cap on the both sides.

  • Page 55: Installing The Power Supply

    Figure 3-4 Installing the defense shedding button on the host system power supply ① Defense shedding button of the power supply module (1) The total power of power supplies configured for the DGS-8000 Series Ethernet Switches must be greater than the operating power of the host.

  • Page 56: Grounding

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation Grounding A PGND is installed on the back of DGS-8000. You must first connect the PGND to the grounding terminal of the cabinet and then connect the grounding terminal to the grounding bar of the equipment room.

  • Page 57: Connecting The Ac Power Supply To The Power Module

    Chapter 3 Switch Installation DGS-8000 Series Hardware Installation Guide To guarantee the security of the person and the device, the DGS-8000 must be well-grounded. The grounding resistence shall be less than 1Ω. Warning A service person shall check whether or not the socket-outlet from which the equipment is to be powered provides a connection the building protective earth.

  • Page 58: 3.10 Installing Single-Boards

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation 3.10 Installing Single-boards Precautions 3.10.1 Always wear an anti-static wrist strap when unplugging the module and the metallic part of the anti-static wrist strap should be fully touched with the skin. Besides, for the sake of security, please not touch any component of the module.

  • Page 59: Connecting The Cables Of The Management Engine Module

    Chapter 3 Switch Installation DGS-8000 Series Hardware Installation Guide 3.12 Connecting the Cables of the Management Engine Module Simple Connection Steps 3.12.1 Connect the end of the shipped console cable with the RJ45 connector to the Console interface of the management engine module, and connect the DB9 connector to the NM or control terminal.

  • Page 60: 3.15 Installation Verification

    DGS-8000 Series Hardware Installation Guide Chapter 3 Switch Installation On the both sides of the chassis, fasten the fibers and twisted pairs to the cabinet cable management ring or cabling chute. For the power cables, you should bind them closely along the bottom of the chassis, in a straight line wherever possible.

  • Page 61: System Debugging

    Chapter 4 System Debugging DGS-8000 Series Hardware Installation Guide System Debugging Establishing the Configuration Environment Establishing the Configuration 4.1.1 Environment Connect the PC to the console port of the switch through the console cable, as shown in Figure 4-1. Figure 4-1 Schematic diagram of the configuration environment Connecting the Console Cable 4.1.2...

  • Page 62: Power-On Startup

    DGS-8000 Series Hardware Installation Guide Chapter 4 System Debugging Setting Terminal Parameters 4.1.3 Step 1: Start the PC and run the terminal simulation program on the PC, such as Terminal on Windows 3.1 or HyperTerminal on Windows 95/98/NT/2000/XP. Step 2：Set terminal parameters. The parameters are as follows: baud rate 9600, data bit 8, parity check none, stop bit 1, and flow control as none.

  • Page 63: Maintenance

    Port configuration information and status  Fan and power supply working status  Temperature status For the monitoring commands, see DGS-8000 series Software Configuration Guide. DGS-8000 Hardware Maintenance Single-board Maintenance 5.2.1 To replace a board, do replacement according to the instructions provided in Sections of Installing Single-boards and Removing Single-boards.

  • Page 64: Power Supply Maintenance

    Module Fuse Specification 5.2.5 The table 5-1 lists the specifications for the module fuses. To replace the old fuse wire with the correspondent new one, please contact the technical support representatives of D-Link Networks. Table 5-1 Specifications for the module fuses...

  • Page 65: Troubleshooting

    Chapter 6 Troubleshooting DGS-8000 Series Hardware Installation Guide Troubleshooting General Installation Troubleshooting Flow...

  • Page 66: Common Troubleshooting Procedures

    DGS-8000 Series Hardware Installation Guide Chapter 6 Troubleshooting Abnormal working after installation installation Check the cabinet Check mounting DGS-8000 switch in the cabinet connection Check the power Check the installation of the power module Check the linecards and other plug-in units on the backplane...
  • Page 67 Chapter 6 Troubleshooting DGS-8000 Series Hardware Installation Guide [Troubleshooting] Please contact D-Link Customer Service Department for technical support. Fault 2: The AC power module does not work. [Fault Description] The Status LED of each linecard is OFF, the Power LED of the fan tray is OFF, and the fan does not work.
  • Page 68 [Troubleshooting] Such problem is related to the settings of the serial port. Check if the settings of such parameters as the baud rate match those in DGS-8000 series Software Configuration Guide. Fault 9: The newly-inserted service card module fails to be powered on.
  • Page 69 If so, please add more power modules to provide the enough power for the power supply. If all checkings are OK, but the newly-inserted service card module still cannot be powered on, please contact D-Link Customer Service Department for technical support.

  • Page 70: Appendixa Connectors And Connection Media

    DGS-8000 Series Hardware Installation Guide Appendix A Connectors and Connection Media AppendixA Connectors Connection Media 1.1000BASE-T/100BASE-TX/10BASE -T Port 1000BASE-T/100BASE-TX/10BASE-T is a port that supports adaptation of three rates, and automatic MDI/MDIX Crossover at these three rates. The 1000BASE-T complies with IEEE 802.3ab, and uses up to 100m of 100-ohm Category-5 or Supper Category-5 UTP or STP...

  • Page 71: Fiber Connection

    Appendix A Connectors and Connection Media DGS-8000 Series Hardware Installation Guide Figure A-3 Connections of the twisted pairs of the 100BASE-TX/10BASE-T 2. Fiber Connection For the fiber ports, select single-mode or multiple-mode fibers for connection according to the fiber module connected. The connection schematic diagram is shown in Figure A-4:...

  • Page 72: Appendixb Mini-Gbic And 10G Xfp Modules

    DGS-8000 Series Hardware Installation Guide AppendixB Mini-GBIC and 10G XFP Modules AppendixB Mini-GBIC and 10G XFP Modules 1000M SFP module (Mini-GBIC module) and 10G XFP module are available to address the requirements of interface types of switch modules. You can select the SFP or XFP module to suit your specific needs.

  • Page 73: Models And Technical Specifications Of The 10G Xfp Module

    AppendixB Mini-GBIC and 10G XFP Modules DGS-8000 Series Hardware Installation Guide 2. Models and Technical Specifications of the 10G XFP Module Table B-2 Models and Technical Specifications of the 10G XFP Module Wavelength Speed Core Optical Intensity Sensitivity Model Media Type...

  • Page 74: Appendixc Switch Lightning Protection

    DGS-8000 Series Hardware Installation Guide AppendixC Switch Lighting Protection AppendixC Switch Lightning Protection 1. Installing AC Power Arrester(lightning protection cable row) The external lightning protection cable row shall be used on the AC power port to prevent the switch from being struck by lightning when the AC power cable is introduced from the outdoor and directly connected to the power port of the switch.

  • Page 75: Installing The Ethernet Port Arrester

    AppendixC Switch Lighting Protection DGS-8000 Series Hardware Installation Guide 1. The power arrester is not provided, the user shall purchase it to address the practical requirement; Warning 2. Make sure that the PE terminal of the power arrester has been well-grounded;...

  • Page 76: Installation Tips

    DGS-8000 Series Hardware Installation Guide AppendixC Switch Lighting Protection connected to the end of IN, while the adapter cable connected to the switch is connected to the end of OUT) and observe whether the LED on the borad is normal or not.
  • Page 77 AppendixC Switch Lighting Protection DGS-8000 Series Hardware Installation Guide device on the switch, it needs to install the arresters on all connection ports for the purpose of the lightning protection.
  • Page 78 The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
  • Page 79 D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright 2004 by D-Link Corporation/D-Link Systems, Inc.

  • Page 80: Product Registration

    Product Registration Register your D-Link product online at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

  • Page 81: Tech Support

    You can find software updates and user documentation on the D- Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the service period, and warranty confirmation service, during the warranty period on this product.
  • Page 82 Technical Support United Kingdom (Mon-Fri) Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm) Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am – 05.30pm) (BT 10ppm, other carriers may vary.) Ireland (Mon-Fri) All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm) €0.05ppm peak, €0.045ppm off peak Times Internet http://www.dlink.co.uk...

  • Page 83: Assistance Technique

    0.12 € TTC/min depuis un poste fixe Du lundi au vendredi de 9h à 19h (hors jours fériés) Asistencia Técnica Asistencia Técnica Telefónica de D-Link: +34 902 30 45 45 0,067 €/min De Lunes a Viernes de 9:00 a 19:00 http://www.dlink.es...
  • Page 84 Pomoc techniczna Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021 Pomoc techniczna firmy D-Link świadczona przez Internet: http://www.dlink.eu/support/ Technická podpora Web: http://www.dlink.cz/support/ E-mail: support@dlink.cz Telefon ČR: +420 211 151 640 nebo SK: +421 (0)692 147 110 Telefonická podpora je v provozu: PO - PÁ od 09:00 do 17:00 Volání...
  • Page 85 Internetin kautta : http://www.dlink.fi Arkisin klo. 9 - 21 Numerosta : 0600 155 57 Teknisk Support D-Link Teknisk Support via Internet: http://www.dlink.se D-Link Teknisk Support via telefon: 0900-100 77 00 Vardagar 08:00-20:00 Assistência Técnica Assistência Técnica da D-Link na Internet: http://www.dlink.pt e-mail: soporte@dlink.es...
  • Page 86 D-Link - ovo spletno stran www.dlink.eu www.dlink.biz/sl Suport tehnic Vă mulţumim pentru alegerea produselor D-Link. Pentru mai multe informaţii, suport şi manuale ale produselor vă rugăm să vizitaţi site-ul D-Link www.dlink.eu www.dlink.ro...
  • Page 87 Technical Support You can find software updates and user do cumentation on the D-Link website. Tech Support for customers in Australia: D-Link Middle East - Dubai, U.A.E. Tel: 1300-766-868 Plot No. S31102, 24/7 Technical Support Jebel Ali Free Zone South, Web: http://www.dlink.com.au...
  • Page 88 Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Iran Israel Unit 5, 5th Floor, No. 20, 17th Alley , Bokharest ‫המגשימים‬ ‫רח‬ 49348 ‫ת‬ ‫" פ‬ ‫קרית מטלון‬ St. , Argentine Sq. ,...
  • Page 89 Техническая поддержка Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link. D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока. Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через Интернет. Техническая поддержка D-Link: +7(495) 744-00-99 Техническая поддержка через Интернет...
  • Page 90 SOPORTE TÉCNICO Usted puede encontrar actualizaciones de softwares o firmwares y documentación para usuarios a través de nuestro sitio www.dlinkla.com SOPORTE TÉCNICO PARA USUARIOS EN LATINO AMERICA Soporte técnico a través de los siguientes teléfonos de D-Link PAIS NUMERO Argentina...
  • Page 91 Suporte Técnico Caso tenha dúvidas na instalação do produto, entre em contato com o Suporte Técnico D-Link por: Chat Online www.dlink.com.br/suporte E-mail suporte@dlink.com.br Back Office backoffice@dlink.com.br *Acionar Garantia para 4 ou mais equipamentos Telefones São Paulo: (11) 2755-6950 *GO: 4052-1850 (Ligação local) *Nordeste: 0800-7024104 *Demais Estados: 4062-1850 (Ligação local)
  • Page 92 D-Link 友訊科技 台灣分公司 技術支援資訊 如果您還有任何本使用手冊無法協助您解決的產品相關問題，台灣 地區用戶可以透過我們的網站、電子郵件或電話等方式與D-Link台灣 地區技術支援工程師聯絡。 D-Link 免付費技術諮詢專線 0800-002-615 服務時間：週一至週五，早上9:00到晚上9:00 (不含周六、日及國定假日) 網 站：http://www.dlink.com.tw 電子郵件：dssqa_service@dlink.com.tw 如果您是台灣地區以外的用戶，請參考D-Link網站全球各地 分公司的聯絡資訊以取得相關支援服務。 產品保固期限、台灣區維修據點查詢，請參考以下網頁說明： http://www.dlink.com.tw 產品維修： 使用者可直接送至全省聯強直營維修站或請洽您的原購買經銷商。...
  • Page 93 Dukungan Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-5731610 Dukungan Teknis D-Link melalui Internet: Email : support@dlink.co.id Website : http://support.dlink.co.id...
  • Page 94 Technical Support この度は弊社製品をお買い上げいただき、誠にありがとうご ざいます。 下記弊社 Web サイトからユーザ登録及び新製品登録を 行っていただき、ダウンロードサービスにて サポート情報、ファームウェア、ユーザマニュアルを ダウンロードすることができます。 ディーリンクジャパン Web サイト URL:http://www.dlink-jp.com...
  • Page 95 技术支持 办公地址：北京市东城区北三环东路 36 号 环球贸易中心 B 座 26F 02-05 室 邮编: 100013 技术支持中心电话：8008296688/ (028)66052968 技术支持中心传真：(028)85176948 各地维修中心地址请登陆官方网站查询 网址：http://www.dlink.com.cn 办公时间：周一到周五，早09:00到晚18:00...

  • Page 96: Registration Card

    8. What category best describes your company? Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing Retail/Chain store/Wholesale Government Transportation/Utilities/Communication System house/company Other________________________________ 9. Would you recommend your D-Link product to a friend? Don't know yet 10.Your comments on this product? __________________________________________________________________________________________ __________________________________________________________________________________________...

Table of Contents