Page 1
SM011 42PD9700C 42PD9700U 42PD9R10 55PD9700C SERVICE MANUAL MANUEL D'ENTRETIEN 55PD9700U WARTUNGSHANDBUCH CAUTION: Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual. Data contained within this Service manual is subject to alteration for improvement.
42PD9700C/U & 55PD9700C/U PRECAUTIONS How to clean the plasma screen panel of the monitor Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet. To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners. How to clean the cabinet of the monitor Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neu- tral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they would cause discoloration, scratches or cracks. Information for users applicable in European Union countries This symbol on the product or on its packaging means that your electrical and electronic equipment should be disposed at the end of life separately from your household wastes.
42PD9700C/U & 55PD9700C/U 3. Service points Lead free solder This product uses lead free solder (unleaded) to help preserve the environment. Please read these instructions before attempting any soldering work. Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder can splatter at high temperatures (600˚C). Lead free solder indicator Printed circuit boards using lead free solder are engraved with an "F." Properties of lead free solder The melting point of lead free solder is 40-50˚C higher than leaded solder. Servicing solder Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.
42PD9700C/U & 55PD9700C/U 4. Component names [Main unit] Control panel Remote Control Receiver SD Memory Card Slot SD MEMO RY CARD Indicating Lamp Sub Power button • The main power switch is located on the lower surface. PUSH-EJECT Channel UP/ button...
42PD9700C/U & 55PD9700C/U 5. New adoption technology [System control micom I001(M30627)] Pin function table PIN NAME Panel: PDP FUNCTION VREF (+5.0V) +5.0V AUDIO_SW1 Audio SW1 OSD_DATA OSD DATA OSD_CLK OSD CLK HP_VOL Head Phone Volume FUNC_1 EXT CONT 1 EXT CONT 1 Function1 EXTernal Control 1 DATA_OUT(FC) FC MicroComputer 3 Lines Bus Data Out /Media Data Out DATA_IN(FC) FC MicroComputer 3 Lines Bus Data In/ Media Data In CLK(FC) FC MicroComputer 3 Lines Bus Clock/ Media Clock BL_INST Black Insert On/Off for 32V LCD (37V=Low) BL_BLINK...
Page 9
42PD9700C/U & 55PD9700C/U PIN NAME Panel: PDP FUNCTION I2C(To the Side of Main Board) SCL1 FE/MSP3455or MSP3415G/SAA5361 I2C(To the Side of Main Board) SDA FE/MSP3455or MSP3415G/SAA5361 HDMI-RESET HDMI-Reset HDMI-HPD_RESET Hot Plug Detect Reset SEL_0 FC Clock/Others SW SEL_1 HDMI/DTT SW TUNER.DET_1 TUNER Detection CE (FLASH) FLASH for Writing STAND.CIR_DET Stand Detection SW_L_OUT Swivel L Output SW_R_OUT Swivel R Output M_SW Bridge Media Circuit Connection Judgement Terminal INITIALIZE Memory Initial BR_MUTE Bridge Media Audio Mute CK_SEL Clock Selector...
Page 10
42PD9700C/U & 55PD9700C/U PIN NAME Panel: PDP FUNCTION SCL3(EEPROM) C(EEPROM) SDA3(EEPROM) C(EEPROM) EPGGO EPGGO EXT_RESET EXTERNAL RESET OSD_CS OSD CS FC_ENABLE FC MicroComputer 3 Lines Enable V_P_DET_1 V_DET_1(Power Save Return) V_P_DET_2 V_DET_2(Power Save Return) Power Delay Control IRQ_DTT DTT IRQ DTT_POWER DTT POWER DISPEN DISPEN/Backlight on HDMI_A_SW HDMI AUDIO SW SCL5 C(Sil9021) SDA5 C(Sil9021) SCL6 I2C(To the Side of Sensor Board) (AD7414) SDA6 I2C(To the Side of Sensor Board) (AD7414)
Page 12
42PD9700C/U & 55PD9700C/U 6. Adjustment ● How to get to Adjustment mode Using the R-side control buttons with the set turned off (standby) can activate it. Press the SUB-POWER( ) button, INPUT SELECT( ) button and button at the same time, and hold for more than 5 seconds. The set turns on in adjustment mode with OSD. ● Changing data and Selecting Adjustment code When the set is in adjustment mode, the cursor , , , and OK buttons of the remote control or R-side control buttons may be used as the adjustment keys. , buttons are used for selecting adjustment code. , buttons are used for changing data values. OK button is used for confirming the data. After finishing the necessary adjustment press MENU button. Adjustment mode is released and the set returns to normal condition.
Page 13
42PD9700C/U & 55PD9700C/U Service adjustment items by I C-bus control (MAIN Part) Function Adj. Max. Init. Device value Value ADJ. Items Mode 0 SUB_CONTRAST (AV1) Sub Composite mode TB274 SUB_CONTRAST (AV2) Sub Composite mode TB274 2 SUB_CONTRAST (AV3) Sub Composite mode TB274 3 SUB_CONTRAST (AV4) Sub Composite mode TB274 4 SUB_CONTRAST (AV5) Sub Composite mode...
Page 14
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 60 Vertical DSB coring for B-Y/B, R-Y/R [CVDSBC0] NTSC/PAL/480i/576i/Multi 6 [CVDSBC1] 480p/576p/080i-50/60/720p 62 Vertical Enhancer CLIP 0:CTI for B-Y/B, R-Y/R [CVECLP0] NTSC/PAL/480i/576i/Multi 63 [CVECLP1] 480p/576p/080i-50/60/720p 64 Horizontal HPF Peak Frequency Switch for B-Y/B, R-Y/R [CHHPF0] NTSC/PAL/480i/576i/Multi 65 [CHHPF1] 480p/576p/080i-50/60/720p 66 Horizontal Enhancer Gain for B-Y/B, R-Y/R [CHEG0] NTSC/PAL/480i/576i/Multi 67 [CHEG1] 480p/576p/080i-50/60/720p 68 Horizontal DSB Gain for B-Y/B, R-Y/R [CHDSBG0] NTSC/PAL/480i/576i/Multi 69 [CHDSBG1]...
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 20 Y Out Level D/K (6.5) TB274 2 Y Out Level I (6.0) TB274 22 Y Out Level L (6.5) TB274 23 Y Out Level L' (6.5) TB274 24 Y Out Level (VIDEO) TB274 25 Y Out Level (TEXT) TB274 26 C Out Level M (4.5) TB274 27 C Out Level B/G (5.5) TB274 28 C Out Level D/K (6.5) TB274 29 C Out Level I (6.0) TB274 30 C Out Level L (6.5)
42PD9700C/U & 55PD9700C/U Adj. Function Max. Init. Device value Value ADJ. Items Mode 80 Sub Contrast 1 Except 15kHz system (15kHz→#262) TA1391FG 8 Sub Contrast 1 TA1391FG 82 Sub Contrast 2 TA1391FG 83 Sub Contrast 2 TA1391FG 84 Sub Color 1 TA1391FG 85 Sub Color 1 TA1391FG 86 Sub Color 2 TA1391FG 87 Sub Color 2 TA1391FG 88 HV THRU 1 NTSC/PAL/480i/576i/480p/576p...
42PD9700C/U & 55PD9700C/U Adj. Function Max. Init. Device value Value ADJ. Items Mode 360 Sub Contrast Gain Adjustment SBCNT[5:0] uPD6405 36 Sub Color Cb Gain Adjustment CBGAIN[5:0] uPD6405 362 Sub Color Cr Gain Adjustment CRGAIN[5:0] uPD6405 363 YGC Auto Mode Select YGCAUTO uPD6405 364 YGC Manual Gain Value Setting YGCVAL[6:0] uPD6405 365 YGC Select YGCOFF uPD6405 366 YGC Control Mode Select1 YGCMVS uPD6405 367 Progressive Y Signal Gain Select YPGAINS[1:0] uPD6405 368 YGC Control Mode Select YGCAVAL[6:0] uPD6405 369 YGC Control Mode Select2 MAXIIRS...
Page 20
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 420 Motion Detection Characteristic Test2 SELDYH2F uPD6405 42 Motion Detection Characteristic Test3 SELDCH2F uPD6405 422 Motion Detection Characteristic Test6 SELD1FL uPD6405 423 Color Demodulation Burst Gate Pulse Range Setting BGP2WD[3:0] uPD6405 424 Color Demodulation Burst Gate Pulse Starting Point Setting BGP2ST[3:0] uPD6405 425 Demodulation Part Force Killer Setting KILON uPD6405 426 Time Constant Setting for Color Demodulation APC APCGAIN[1:0] uPD6405 427 Time Constant Setting for Color Demodulation ACC ACCGAIN[1:0] uPD6405 428 Control Characteristic Setting for Color Demodulation ACC ACCLIM[3:0] uPD6405 429 SECAM Burst Pulse Position Correction SBGTDL[2:0]...
Page 21
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 480i/576i uPD6405 48 Brightness Signal Noise Coring (highpass) YCORH[2:0] NTSC uPD6405 Except NTSC uPD6405 480i/576i uPD6405 484 Color-Difference Signal Noise Coring2 CCORB[3:0] NTSC uPD6405 Except NTSC uPD6405 480i/576i uPD6405 487 Color-Difference Signal Noise Coring2 Control CCOREN NTSC uPD6405 Except NTSC uPD6405 480i/576i uPD6405 490 LTI Correction Amount Adjustment LTIGAIN[3:0]...
Page 23
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 600 Vertical Sync Signal Pull-in Range Select VLIM uPD6405 60 V Counter Free Run Setting at No Signal Mode NSGVFRUN uPD6405 602 Line Lock Clock Free Run Settng at No Signal Mode NSGFRUN uPD6405 603 Vertical Sync Signal Correction VDCOR uPD6405 604 Line Lock PLL Gain Setting HPLLG[4:0] uPD6405 605 Line Lock PLL Phase Detection Condition Setting HPLLSIG uPD6405 606 Line Lock PLL Response Correction Setting HPLLH2 uPD6405 607 Line Lock PLL Response Correction Coefficient1 HPLLH21[7:0] uPD6405 608 Line Lock PLL Response Correction Coefficient2 HPLLH22[7:0] uPD6405 609 PWM Select for Clamp PWMSEL[1:0]...
Page 24
42PD9700C/U & 55PD9700C/U Adj. Function Max. Init. Device value Value ADJ. Items Mode 660 Y/C timing for M(4.5) system RF-Main uPD6405 66 Y/C timing for (5.5MHz PAL/NTSC4.43) system RF Main uPD6405 662 Y/C timing for (5.5MHz SECAM) system RF Main uPD6405 663 Y/C timing for (6.0MHz PAL/NTSC4.43) system RF Main uPD6405 664 Y/C timing for (6.0MHz SECAM) system RF Main uPD6405 665 DAC Output Imapge Sync Comparison Setting DACLEVEL uPD6405 666 Blanking Period Level Setting INBLK50IRE uPD6405 667 Line Lock PLL Gain Setting HPLLG[4:0]...
Page 25
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 720 EURO SOUND SYSTEM DK Disable 0:Enable, 1Disable M30627 72 Remote Function available 0:NO, 1:YES M30627 722 Key Function available 0:NO, 1:YES M30627 723 Terminal Mode Function available 0:Not Available, 1:Available RS232C M30627 Set Taiwan/Korea/South America 0:Others 1: Taiwan/Korea/South M30627 America 725 Language (Refer to below) M30627 726 Hotel Mode(0:No, 1:Yes) M30627 727 Initial Audio Level available (0:No 1: Yes) M30627 728 Initial Audio Level M30627...
Page 26
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 780 TA1391FG Read Data(06h) TA1391FG 78 TA1391FG Read Data(07h) TA1391FG 782 SiI9021 Read Data SYNC1 : VSYNC/Clock detect/Sync detect 1 HDMI 783 SiI9021 Read Data NHRDL1 : N hardware value 1 Last 7Bits HDMI 784 SiI9021 Read Data NHRDM1 : N hardware value 1 Middle 7Bits HDMI 785 SiI9021 Read Data NHRDH1 : N hardware value 1 First 4Bits HDMI 786 SiI9021 Read Data CHRDL1 : CTS hardware value 1 Last 7Bits HDMI 787 SiI9021 Read Data CHRDM1 : CTS hardware value 1 Middle 7Bits HDMI 788 SiI9021 Read Data CHRDH1 : CTS hardware value 1 First 4Bits HDMI 789 SiI9021 Read Data ACR1 : ACR PLL hardware value 1...
Page 27
42PD9700C/U & 55PD9700C/U Function Adj. Max. Init. Device value Value ADJ. Items Mode 838 C3TBL_SEL_G 839 C3OTLEV_SEL_B 840 C3OTLEV_SEL_G 84 C3OTLEV_SEL_R 842 Reserved for EURO 843 Reserved for EURO 844 Reserved for EURO 845 Reserved for EURO 846 Reserved for EURO 847 Reserved for EURO 848 Reserved for EURO 849 Reserved for EURO 850 Reserved for EURO 85 Reserved for EURO...
Page 28
42PD9700C/U & 55PD9700C/U Service adjustment items by I C-bus control (SUB adjust menu) (*The change to a sub menu. press “ok” key after no.899 with a main menu) Function Adj. Init. Max. Device Value ADJ. Items Mode 0 R DRIVE1 [RF/VIDEO/HDMI] COOL PDP/FC G DRIVE1 [RF/VIDEO/HDMI] COOL PDP/FC 2 B DRIVE1 [RF/VIDEO/HDMI] COOL PDP/FC 3 R DRIVE2 [RF/VIDEO/HDMI] NORMAL PDP/FC 4 G DRIVE2 [RF/VIDEO/HDMI]...
Page 29
42PD9700C/U & 55PD9700C/U Function Adj. Init. Max. Device Value ADJ. Items Mode 60 Tint Center (CM) HDMI-YPbPr(1080i-50/60/720p) 6 Tint Center (CM) →HDMI(VGA) 62 Tint Center (CM) 63 Tint Center (CM) DSUB-RGB 64 Center of Sharpness (HV Enhancer Gain for Y) 65 Center of Sharpness (HV Enhancer Gain for Y) VIDEO 66 Center of Sharpness (HV Enhancer Gain for Y) Scart-RGB(50/60Hz) 67 Center of Sharpness (HV Enhancer Gain for Y) 480i/576i 68 Center of Sharpness (HV Enhancer Gain for Y) 480p/576p 69 Center of Sharpness (HV Enhancer Gain for Y) 720p 70 Center of Sharpness (HV Enhancer Gain for Y)
Page 30
42PD9700C/U & 55PD9700C/U Function Adj. Init. Max. Device Value ADJ. Items Mode 20 [YC0R2] 480i/576i/Scart-RGB(50/60Hz) 2 [YC0R3] 480p/576p 22 [YC0R4] 080i-50/60/720p 23 [YC0R5] NTSC/PAL- S Input 24 [YC0R2'] 25 Coring Amplitude for B-Y/B, R-Y/R [CC0R0] NTSC/PAL/480i/576i/Multi 26 [CC0R1] 480p/576p/080i-50/60/720p 27 Main YFRNR Input Gain 2 Picture [MYNRG0] Except HD-HD 28 (Sub Side of HD-NTSC, HD-PAL) [MYNRG1] HD-HD 29 4 Picture [MYNRG2] NT-* /PAL-*...
Page 31
42PD9700C/U & 55PD9700C/U Adj. Function Init. Max. Device Value ADJ. Items Mode 80 Horizontal HPF Peak Frequency Switching for Y/G [YHHPF0] NTSC/PAL/480i/576i/Multi 8 [YHHPF1] 480p/576p 82 [YHHPF2] 080i-50/60/720p 83 Initial value of Contrast (Degradation Reduction1) Extend 1 of Panel Life function PDP/FC 84 Interval time of correction time (Degradation Reduction1) Extend 1 of Panel Life function PDP/FC 85 Additional value of Contrast (Degradation Reduction1) Extend 1 of Panel Life function PDP/FC 86 Initial value of Contrast (Degradation Reduction2) Extend 2 of Panel Life function PDP/FC 87 Interval time of correction time (Degradation Reduction2) Extend 2 of Panel Life function PDP/FC...
42PD9700C/U & 55PD9700C/U Function Adj. Init. Max. Device Value ADJ. Items Mode 233 Offset value of gain for Black Stretch function LOW mode at HD signal 234 Offset value of gain for Black Stretch function MID mode at HD signal 235 Offset value of gain for Black Stretch function HIGH mode at HD signal 236 Menu init. Contrast mode (Normal [0] Auot [1] / Dynamic. [2]) For Dynamic 237 Menu init. Contrast mode (Normal [0] Auot [1] / Dynamic. [2]) For Natural 238 Menu init. Contrast mode (Normal [0] Auot [1] / Dynamic. [2]) For Cinema 239 Y/G Horizontal Enhancer Gain [YHEG2] 1080i-50/60/720p-60 (HDMI) 240 [YHEG2’] 720p-50 (HDMI *EX. HDMI→#160-161 24 dummy241 242 dummy242 243 dummy243...
Page 33
42PD9700C/U & 55PD9700C/U Item Power Unit Vs, Va Adjustment Preparation Procedure (1) Turn on the set and perform (1) Turn Vs ADJ to adjust Vs voltage pre-heat run more than 1 min to be within ±0.1V of the value on burn-in screen.
Page 34
42PD9700C/U & 55PD9700C/U RGB Amplitude Adjustment (PC D-Sub input) Item Preparation Procedure Receive PC signal (VGA [60Hz]), and indicate Input RGB amplitude adjustment signal of VGA Service Adjustment Menu.(Main) (60Hz) into RGB2 [D-sub] terminal. Select No.897 of Service Adjustment Menu.
Page 35
42PD9700C/U & 55PD9700C/U Video Colour Temperature Adjustment (Cool) Item Adjustment Preparations Adjustment Procedures Set the signal generator output as All White. Perform the following adjustment with the remote control Component signal (480i) Set the CRT colour analyzer (CA100) at the centre Video level : 0.700Vp-p...
Page 36
42PD9700C/U & 55PD9700C/U Video Colour Temperature Adjustment (Warm) Item Preparation Procedure (1) Set signal generator output as Perform the following adjustment with the remote All White (Window ratio: 100%). control. (2) Component signal (480i) Set the CRT Colour Analyzer (CA100) at the centre Video level : 0.700Vp-p...
Page 37
42PD9700C/U & 55PD9700C/U Procedure of re-install new software of Digital module software for 42PD9700 1. RS232C cable should be connected to RS232C terminal of TV set. RS232C cable should be connected. 2. TV set turn ON. 3. Press hold [S.MODE], [YELLOW] and [Blue] button of remote controller until appears the service menu. 4. Set data of No 888 from [0] to [1] then press [OK] button. 5. RS232C cable should be connected between TV set and PC. 6. Appeared programe menu after double crick Hyper Termi- nal I con. Condition of Transfer Bit rate:115200 Data bit:8 Parity: none Stop bit:1 Flow: none 7. Crick “Transfer” then select ”File send”. 8. Select required software file in the folder.
Page 38
42PD9700C/U & 55PD9700C/U 9. Turn Off the TV set. 10. Click “Send” in the “ File send” menu. 11. Turn On the TV set. 12. Screen will change and digit of Packet window will start from “0”. 13. Should be wait until screen has “OK” information. 14. Disconnect RS232C cable. 15. Press hold [S.MODE], [YELLOW] and [Blue] button of remote controller until appears the service menu 16. data of no.888 should be change back from [1] to [0] then press [OK] button. 17. Turn Off the TV set. After confirmation of a soft version is necessary. SERIAL(RS-232C) Connector pin specification. signal name note RXD0 Data from PC TXD0 Data to PC Set GND ↔ PC GND FRONT VIEW(Female)
42PD9700C/U & 55PD9700C/U 7. Troubleshooting How to get to Burn-in mode This mode displays the test patterns of some single color raster in turn. These signals are from built-in gener- ator of panel. So it can be presumed that maybe the panel has some trouble when the screen of Burn-in mode is abnormal. Using the R-side control buttons with the set turned off (standby) can activate this mode. Press the SUB-POWER( ) button, INPUT SELECT(...
Page 40
42PD9700C/U & 55PD9700C/U Power unit NO POWER NO Vs,Va,Vcc,STB impedance check impedance FUSE,R004,R005 check D001 D001 impedance check Q003/Q004 Q003/Q004 check voltage over 130V R004,R005 etc D011(k)-Q101 Heat Sink impedance check Q101 under 130V Q101,IC101 See NO PICTURE Q101, IC101 IC101, D150 R004,R005 etc &...
Page 41
42PD9700C/U & 55PD9700C/U Power Power cannot be turned on (LED does not light) the input voltage applied to Power supply unit ? (CN61 (1),(3)) Main switch AC Fuse AC inlet Filter PCB (SW PCB) F902 T6.3AH 250V Are the voltages applied to...
Page 42
42PD9700C/U & 55PD9700C/U Power Power cannot be turned on (Continued) * Check stand-by Does the red-LED light? * Check STB5V for FC PCB the voltage applied to PJF1 (3)pin ? (Refer to Table2) Sub-power PCB * Check EPGgo signal the voltage...
Page 43
42PD9700C/U & 55PD9700C/U [PW3 Sound Circuit] No sound of TV Are waveforms at Check pin 2,4,5,6 of PAF1? SOUND PCB Are waveforms at Check pin 45,47 of PFM1(L,R)? FC PCB Are waveforms at pin 43,45 of I201(L,R)? Check around PMF1...
Page 44
42PD9700C/U & 55PD9700C/U [PW3 Sound Circuit] No sound of HDMI1 No sound of HDMI2 JF400 JF401 Are waveforms at Check pin 2,4,5,6 of PAF1? SOUND PCB Are waveforms at Check pin 45,47 of PFM1(L,R)? FC PCB Are waveforms at Are waveforms at...
Page 45
42PD9700C/U & 55PD9700C/U [PW3 Sound Circuit] No sound of Bridge Media Unit Are waveforms at Check pin 2,4,5,6 of PAF1? SOUND PCB Are waveforms at Check pin 45,47 of PFM1(L,R)? FC PCB Are waveforms at pin 45,47 of PMF1(L,R)? Check around...
Page 46
42PD9700C/U & 55PD9700C/U [PW3 Sound Circuit] Check SOUND PCB Are waveforms at pin 1,2,4,5 of PAS1and pin 1,2,5,6 of PAS2? Check around SPEAKER UNIT Are waveforms at pin 34,35,38,39,46,47, 50,51 of I401? Check around PAS1,PAS2 Is voltage at pin 10,20 of I401 (RESET-N="H")?
Page 47
42PD9700C/U & 55PD9700C/U [PW3 Sound Circuit] Check FC PCB Are waveforms at pin 2,4,5,6,10,11 of PFA ? Check around PAF1 Are waveforms at pin 31,32,33 of I600? Check around PFA1 Are waveforms at pin 29,38,40 of I600? Check I600 Are waveforms at...
Page 48
42PD9700C/U & 55PD9700C/U Main Picture [Main PCB Circuit] No picture, no color or dark Yes(Sub picture) Sub picture? Trouble of Sub picture (Signal picture or Main picture ) (RGB(DTT,SCART) or Component Are waveform at Video except 480i and 576i) SCART TP605(Y), TP606(Cb), and Yes(SCART,Comp)
Page 49
42PD9700C/U & 55PD9700C/U Sub Picture [Main PCB Circuit] Trouble of Sub picture Are waveform at TP608(Y), TP609(Cb), and TP610(Cr)? Check FC PCB Are waveforms at 42pin(Y), 44pin(Cb), and 46pin(Cr) of I601? Check Q604, Q605, Q606 SCART Yes(SCART,Comp) Input(DTT,SCART) or Compo- Component? nent Input? (RGB(DTT,SCART) or Component...
Page 50
42PD9700C/U & 55PD9700C/U Main Syincronization [Main PCB Circuit] No Sync or Invalid Sync Yes(Sub picture) Sub picture? Trouble of Sub picture (Signal picture or Main picture ) Are waveform at TP601(H) and TP602(V)? Check FC PCB Are waveforms at 61pin(H) and 58pin(V) of I601?
Page 51
42PD9700C/U & 55PD9700C/U Sub Syncronization [Main PCB Circuit] Trouble of Sub picture Are waveform at TP603(H) and TP604(V)? Check FC PCB Are waveforms at 45pin(H) and 48pin(V) of I601? Check I602 (Component Video) Input(DTT,SCART) or Component Input? Check I601 and Input terminal (RF/Composit Video/S-Video)
Page 52
42PD9700C/U & 55PD9700C/U Teletext [Main PCB Circuit] No Teletext (Sub picture) Sub picture? waveform at TP608(Y), (TV+Text) TP609(Cb), and TP610(Cr)? Check FC PWB (Signal picture ) waveform at TP605(Y), waveforms at TP606(Cb), and 42pin(Y), 44pin(Cb), and TP607(Cr)? 46pin(Cr) of I601? Check FC PCB...
Page 53
42PD9700C/U & 55PD9700C/U Photo Input Unit No picture Check to FC Unit at P301 connector 10pin, 12pin, 14pin Check FC PCB Photo Input Unit or cable (Photo Input Unit FC Unit check to cable insertion) HDMI Picture [FC PCB Circuit] No picture Analog Recom- connection with HDMI...
Page 54
42PD9700C/U & 55PD9700C/U 8. Self-Diagnosis Function This chassis has 2 modes of self-diagnosis function. (1) PDP panel check mode: It indicates the one latest record of the PDP panel failure with blinking of the power indication light (LED). (2) Signal circuit check mode: It indicates the check result on some points of the signal circuit and the history of them with On-Screen Display (OSD). PDP panel self-diagnosis function This function is for a PDP panel failure with no picture. To enter to this Self-Diagnosis mode, follow the next steps: Preparation: 1) The Power Cord should be connected to AC line and the Main Power switch should be turned on. 2) Turn the power off by the SUB-POWER( ) button of the monitor or the remote control. Procedure: 1) Press the SUB-POWER( ) button and button on the bottom of the monitor at the same time, and keep it for more than 5 seconds after the power turned on.
Page 55
42PD9700C/U & 55PD9700C/U Signal circuit self-diagnosis function This function is for the failure of the signal circuit, for example the phenomenon as below: "Sometimes power turns off abnormally." "Sometimes picture disappears abnormally." To enter to this Self-Diagnosis mode, follow the next steps: Preparation: 1) The Power Cord should be connected to AC line and the Main Power switch should be turned on. 2) Turn the power off by the SUB-POWER( ) button of the monitor or the remote control. Procedure: 1) Press the SUB-POWER( ) button and button on the bottom of the monitor at the same time, and keep it for more than 5 seconds after the power turned on. 2) The monitor will be turned on, and it will display On-Screen Display of the Self-check result and the failure history as below. 3) Any operation would cancel the Self -Diagnosis mode. 4) The following table shows the OSD symbols and contents of failure PWB in which failure most probably would be allocated according to the number of blinks. Check result [OSD] Check item Self Check H11: OK H15: OK Self check result area H16: OK...
Page 57
42PD9700C/U & 55PD9700C/U Basic circuit diagram list PCB assembly Power Unit 1 ..........57 PCB assembly Power Unit 2 ..........58 PCB assembly Power Unit 3 ..........59 PCB assembly Power Unit 4 ..........60 PCB assembly Power Unit 5 ..........6 PCB assembly MAIN 1 ............62 PCB assembly MAIN 2 ............63 PCB assembly MAIN 3 ............64 PCB assembly MAIN 4 ............65 PCB assembly MAIN 5 ............66 PCB assembly LED PDP ............67 PCB assembly SWIVEL .
Page 67
MAIN 2 SM 011 MAIN BOARD CIRCUIT SHEET 5...
Page 68
TO FILTER PCB TO FC PCB LED PCB POWER SWITCH PCB TO MAIN PCB TERMINAL PCB TO PSU SWIVEL PCB FROM AC INLET TO (AC) SWITCH PCB FILTER PCB TO MAIN PCB : NOT MOUNTED SM 011 MISC. CIRCUITS...
Page 72
CLAMP Switching To FC4 To coax change SW To FC4 To FC4 To FC4, Sub -com To IC905 Video / BM Signal change SM 011 FC BOARD CIRCUIT SHEET 1...
Page 73
Sync processing To I C103 Video / RGB change To MAIN -com cync detect FC -com To IC705 BM / HDMI / OTHER coax change processing SM 011 FC BOARD CIRCUIT SHEET 2...
Page 82
SM 011 MAIN BOARD - COMPONENT (TOP) SIDE...
Page 83
SM 011 MAIN BOARD - SOLDER (BOTTOM) SIDE...
Page 84
LED PDP BOARD LED LCD BOARD SWIVEL BOARD SUB-POWER BOARD COMPONENT (TOP) SIDE COMPONENT (TOP) SIDE TERMINAL BOARD FILTER BOARD COMPONENT (TOP) SIDE COMPONENT (TOP) SIDE SM 011 MISC. BOARDS...
Page 85
SOLDER (BOTTOM) SIDE COMPONENT (TOP) SIDE SM 011 FC BOARD...