1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the (READING SHOULD circuit board. NOT BE ABOVE 0.5mA) Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
2 Product Specifications 2-2 Pin Assignments Sync 15-Pin Signal Cable Connector Type Separate Composite Sync-on-green (Option) Pin No. Green Green Green + H/V Sync Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-R GND-R GND-R GND-G GND-G GND-G GND-B...
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart Mode VESA VGA1/70 Hz VGA3/60 Hz 800/60 Hz VGA2/70 Hz 640/72 Hz 800/56 Hz 640/75 Hz...
Page 7
2 Product Specifications Table 2-2 Timing Chart Mode VESA VGA2/ VGA3/ 1280/60 Hz 1280/75 Hz 640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 70 Hz 60 Hz 1280 x 1024 1280 x 1024 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the DI19PS monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions : 1. Disconnect the monitor from the power source before disassembly. 2.
Page 9
3 Disassembly and Reassembly 6. Remove shield from the panel and disconnect inverter cabel, LVDS cable from the main boards. 7. Remove main board from the panel. 3-2 Replacement Order of Lamp Assemblies 1. After confirm there is nothing on the desk, turn the LCD module over and put it on a flat desk set to the ground.
Page 10
3 Disassembly and Reassembly Slide the lamp unit 3. Slide the lamp unit. Please take out the lamp units from the LCD module. Slide the lamp unit 4. Please fix the new lamp units on the LCD module : opposite process 2 and 3. 3-3 Reassembly Reassembly procedures are in the reverse order of disassembly procedures.
Page 11
3 Disassembly and Reassembly Memo DI19PS...
4 Alignments and Adjustments This is to illustrate jig installation required for DDC EDID input. DDC EDID input is necessary to adjust black level and R, G, B for FPD when replacing AD board. This section also explains how to adjust OSD when replacing panel or lamp.
Page 13
4 Alignments and Adjustments 4-4 OSD Adjustment for Panel Replacement 1. Repeat 1, 2 and 3 in above 4-2. 2. Press the key and hold until Information is selected. Figure 4-3. 3. Press the key again to execute Information. 4. Press the key and hold until Panel is selected. Figure 4-4.
Page 14
4 Alignments and Adjustments 4-5-1 How to Display Service Function OSD 1. With the monitor powered off, press power key and hold until it beeps 10 times. 2. Power the monitor on for screen display. 3. Press the power key and hold until the following figure displays. Figure 4-7.
Page 15
4 Alignments and Adjustments Figure 4-12. 4-5-3 How to Abjust SVC Function OSD • Always adjust SVC Function OSD after replacing any panel or lamp. • Panel Replacement After replacing a panel, press the key and hold until Panel is selected. Press Panel shortly again. Ch.No of the Panel increases by 1 while panel time information (Time(Hr)) changes to '0'.
Page 16
4 Alignments and Adjustments This function protects a displayed image from sticking when the same image is displayed for an extended period of time. PixelShift On : 0x01 for EEPROM 0x2E PixelShift Off : Others Please see the below figure for movement path. It takes 4 minutes for 1-step movement. (32 steps = 128 minutes) Figure 4-15.
Page 17
4 Alignments and Adjustments Memo DI19PS...
5 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1280 x 1024 • H-frequency: 48 kHz • V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 19
5 Troubleshooting 5-2 No Video Power indicator is green. Does DC 5V appear at Replace IC205 or Pin 1, 2 and 3 of CN401? check it’s related circuit. Does the pulse Does the pulse appear Does the pulse appear at appear at Pin 74 at Pin 6 and 8 of IC101? Pin 126 and 127 of IC401?
7 Electrical Parts List ❈ You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 7-1-1 DI19PS Main PCB Parts Level Loc. No. Code No. Description Specification Remarks DI19PSQAQ/EDC E18-DI19PSQAQ/EDC SEC,LTM190E4-L01 BN94-00512G ASSYPCBMAIN-E18 DI19PS CIS3 0204-001677 FLUX DF-201TVS,MIX,0.820,FLUX13%,G...
Page 40
Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea, 442-742 Printed in Korea ❈ This Service Manual is a property of Samsung P/N : BN82-00110E-00 Electronics Co., Ltd. http : //www.samsungmonitor.com (SyncMaster Worldwide) Any unauthorized use of Manual can be punished http : //www.samsung-monitor.com (SyncMaster USA)