Page 1
XV-S300BK/XV-S332SL XV-S402SL/XV-S403SG SERVICE MANUAL DVD VIDEO PLAYER XV-S300BK / XV-S332SL XV-S402SL / XV-S403SG Area Suffix UJ ------------ U.S.A.Militaly A ------------------- Australia UB -------------- Hong Kong UG --- Turkey,South Africa, STANDBY/ON OPEN/ Egypt CLOSE UP --------------------- Korea MUTING US --------------- Singapore...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG SECTION 1 Important Safety Precautions 1.1 Safety Precautions (1) This design of this product contains special hardware and Measure the AC voltage across the resistor with the AC many circuits and components specially for safety purposes. voltmeter. For continued protection, no changes should be made to the...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 1.5 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 1.7 Important for laser products (1) CLASS 1 LASER PRODUCT (5) CAUTION : If safety switches malfunction, the laser is able (2) DANGER : Invisible laser radiation when open and inter to function. lock failed or defeated. Avoid direct exposure to beam.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 1.8 Precautions for Service 1.8.1 Handling of Traverse Unit and Laser Pickup (1) Do not touch any peripheral element of the pickup or the actuator. (2) The traverse unit and the pickup are precision devices and therefore must not be subjected to strong shock.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG SECTION 2 Disassembly method There is a part different from the photograph according to the model and the destination though explains this disassembly method by using XV-S403SG for Australia. 2.1 Main body 2.1.1 Removing the top cover (see Fig.2-1) (1) Remove the two screws A attaching the top cover on both sides of the body.
Page 8
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.1.4 Removing the rear panel (see Fig.2-5) • Prior to performing the following procedure, remove Rear panel the top cover. (1) Remove the seven screws D attaching the rear panel on the back of the body. • As for the screw D, the number and the position are dif- ferent according to the destination and model.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.2 Loading assembly section 2.2.1 Removing the clamper assembly (See Fig.2-9) (1) Remove the four screws A attaching the clamper assem- Joint a Joint a bly. (2) Move the clamper in the direction of the arrow to release the two joints a on both sides.
Page 10
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.2.3 Removing the traverse mechanism assembly (See Fig.2-12 and 2-13) • Prior to performing the following procedure, remove the clamper assembly and the tray. (1) Remove the four screws B attaching the traverse mecha- Traverse mechanism nism assembly. assembly...
Page 11
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.2.5 Removing the motor assembly (See Fig.2-15 and 2-16) • Prior to performing the following procedure, remove the clamper assembly, the tray, the traverse mechanism assem- bly and the elevator. Belt (1) Remove the belt from the pulley. (2) Remove the screw C attaching the motor assembly.
Page 12
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Pulley gear Idle gear Pulley gear bracket Pulley gear Idle gear Pulley gear bracket Tads h Pulley gear Motor assembly Fig.2-17 2.2.6 Removing the Idle gear/pully gear/middle gear/ slide cam(See Fig.2-17 to 2-19) • Prior to performing the followong procedure,remove...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.3 Traverse mechanism assembly section 2.3.1 Removing the feed motor assembly (See Fig.2-20) (1) Unsolder the two soldering j on the spindle motor board. Feed motor assembly (2) Remove the two screws F attaching the feed motor assembly. Pickup...
Page 14
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.3.3 Removing the pickup (See Fig.2-24 and 2-25) Pickup (1) Remove the screw I attaching the T spring (S) and the Joint n shaft holder. Remove also the plate. Shaft holder ATTENTION: When reattaching,make sure that the T spring(S)presses the shaft.
Page 15
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 2.3.5 Removing the spindle motor assembly Spindle motor (See Fig.2-27 to 2-29) (1) Remove the three screws L attaching the spindle motor on the bottom of the mechanism base. ATTENTION: When reattaching, pass the card wire extending from the spindle motor board through the notch of the spin- dle base.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG SECTION 3 Adjustment method 3.1 Initialization method If microprocessor (IC401,IC402,IC451) or pick-up is replaces, initialize the DVD player in the following matter (1) Take out the disc and close the tray. (2) Unplug the power plug. (3) Insert power plug into outlet while pressing both "PLAY" button and "OPEN/CLOSE" button.
Page 17
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.2.2 For Jitter value The jitter value is displayed on the FL display referring to the previous page. The jitter value is displayed by the hexadecimal number. In the following cases, please "Flap adjustment of the pick-up guide shaft" referring to the following page.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.3 Flap adjustment of the pick-up guide shaft 3.3.1 Tool list for adjustment • Hex wrench for adjustment Off-the-shelf (1.3mm) • Test disc VT-501 or VT-502 • Stud (four pieces set) Parts No. : JIGXVS40 (One is not used though there are four. ) Fig.3-4...
Page 19
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.3.3 Adjustment preparation (1) The mechanism assembly is made in the state from the main body from which is detached referring to the disassembly method. (2) Three studs are installed in the mechanism assembly respectively. (3) The servo control board is removed from the mechanism assembly, and puts into the state set up as shown in figure. (Each wire connected by the servo control board this time leaves the connection maintained.)
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.4 Attention when pick-up is exchanged (1) Flexible wire, pick-up spring, switch actuator, and lead spring are removed from an old pick-up(broken the one). Switch actuator < Guide > Lead spring Flexible wire, pick-up spring and switch actuator, lead spring are removed without each decomposing while assembled.
The EEPROM is initialized. Refer to the initialization method. Opening picture check (Power ON) It should be display "JVC" Muting working The noise must not be had to the performance beginning when you push "PLAY" button or at ON/STANDBY. FL Display The mark and the logo, etc.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.6 Troubleshooting 3.6.1 Servo volume Press OPEN /CLOSE key Is tray Confirmation of tray drive circuit operation and circuit in surrounding correct? Is the traverse moving See "(3) Traverse movement error" along the innermost in "Check points for individual errors"...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.7 Check points for each error 3.7.1 Spindle start error (1) Defective spindle motor • Are there several ohms resistance between each pin of CN201 "5-6","6-7","5-7"? (The power supply is turned off and measured.) • Is the sign wave of about 100mVp-p in the voltage had from each terminal? [ CN201"9"(H1-),"10"(H1+),"11"(H2-),"12"(H2+),"13"(H3-),"14"(H3+) ]...
Page 24
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.7.3 Traverse movement NG (1) Defective traverse driver • Has the voltage come between terminal of CN101 "1" and "2" ? (2) Defective BTL driver (IC201) • Has the motor drive voltage gone out to IC201"17" or "18"? (3) Has the control signal come from servo IC or the microcomputer? •...
Page 25
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 3.7.9 Neither picture nor sound is output (1) It is not possible to search • Has the tracking been turned on? • To "(5) Tracking ON NG" in "Check points for each error" when the tracking is not normal.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.4 BA5983FM-X (IC201) : 4CH Driver 4.4.1 Block diagram STAND BY Level Shift Level Shift Level Shift Level Shift STAND BY CH1/2/3 4.4.2 Pin function Pin No. Symbol Description Pin No. Symbol Description BIAS IN Input for Bias-amplifier VO4(-)
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.6 BA6664FM-X (IC251) : 3Phase Motor Driver 4.6.1 Pin layout 4.6.2 Block diagram DRIVER GAIN SWITCH GAIN CONTROL CURRENT SENSE AMP HALL AMP TOROUE SENSE AMP SHORT BRAKE CK Q BRAKE MODE Hall Bias...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.6.3 Pin function Pin No. Symbol Description Non connect Output 3 for spindle motor Non connect Output 2 for spindle motor Non connect Non connect Output 1 for spindle motor Connect to ground Positive input for hall input AMP 1...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.8 K3N5V1000F-J001 (IC402) :P2 ROM of 1,048,576word x 16 bit / 2,097,152 word x 8 bit 4.8.1 Pin layout 4.8.2 Block diagram x 8 / x 16 Output select BYTE Memory Cell Matrix 1,048,576 x 16-Bit or 2,097,152 x 8-Bit...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.10MN101C35DLD (IC701) : System controller 4.10.1 Pin function Pin No. Symbol Description DDATA DAC control data DACOCS DAC control chip select DCLK DAC control clock MUTE1 Muting signal to IC601 VIDEO SW Component / S-Video switch input MODE 1,2...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.11MN102L62GLH (IC401) : Unit CPU 4.11.1 Pin function Pin No. Symbol Function Pin No. Symbol Function WAIT Micon wait signal input Connect to TP406 Read enable Connect to TP405 SPMUTE Spindle muting output to IC251 P85/TM5IO Connect to TP404...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.12MN103S28EGA (IC301) : Super optical disc controller 4.12.1 Terminal layout 4.12.2 Block diagram Host I/F DVD-ROM Analog MPEG I/F Formatter CD-PRE ATAPI High speed IO bus Instruction Servo I/O CGEN memory (core 1 I/O) (40KB) 32 bit CPU core...
Page 36
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.12.4 Pin function (MN103S28EGA : 2/4) Pin No. Symbol Description Read signal input from system controller 37~44 CPUDT7~0 System control data CLKOUT1 Non connect MMOD Test mode switch signal NRST System reset MSTPOL Master terminal polarity switch input SCLOCK...
Page 37
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.12.5 Pin function (MN103S28EGA : 3/4) Pin No. Symbol Description PLFLT1 Connect to capacitor 1 for PLL AVSS Connect to ground for analog circuit Connect to resistor for VREF reference current source VREFH Reference voltage input (2.2V) PLPG Non connect VHALF Reference voltage input (1.65V)
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.12.6 Pin function (MN103S28EGA : 4/4) Pin No. Symbol Description Connect to ground VDD3 Power supply terminal for I/O (3.3V) HDD1 ATAPI host data 1 HDD13 ATAPI host data 13 HDD2 ATAPI host data 2 HDD12 ATAPI host data 12...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.14MN35505-X (IC703) : DAC 4.14.1 Terminal layout LRCK DVDD1 DVDD2 VCOF DVSS2 XOUT DVSS1 OUT1C OUT2C AVDD1 AVDD2 OUT1D OUT2D AVSS1 AVSS2 4.14.2 Pin function Pin No. Symbol Description Control signal for DAC Digital data input LRCK L and R clock for DAC...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.15S-93C66AFJ-X (IC451) : EEPROM 4.15.2 Pin function 4.15.1 Pin layout Pin No. Symbol Description Non connect Power supply terminal Chip select input Serial clock input Serial data input Serial data output Connect to ground Non connect 4.15.3 Block diagram...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.17ZIVA-4.1-PB0 (IC501) : Back end - Digital decoder 4.17.1 Terminal layout 4.17.2 Pin function (1/5) Pin No. Symbol Description Read strobe input Read/write strobe input VDD_3.3 Power supply terminal 3.3V WAIT Transfer not complete / data acknowledge. Active LOW to indicate host initiated transfer is complete.
Page 42
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.17.3 Pin function (ZIVA-4.1-PB0 : 2/5) Pin No. Symbol Description Connect to ground Non connect Non connect Non connect Non connect Non connect PIO0 I/O Programmable I/O terminal Connect to ground VDD_3.3 Power supply terminal 3.3V PIO1 I/O Programmable I/O terminal...
Page 43
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.17.4 Pin function (ZIVA-4.1-PB0 : 3/5) Pin No. Symbol Description MADDR6 SDRAM address MADDR5 SDRAM address VDD_2.5 Power supply terminal 2.5V Connect to ground MADDR4 SDRAM address SDRAM write enable SD-CAS Active LOW SDRAM column address VDD_3.3 Power supply terminal 3.3V...
Page 44
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.17.5 Pin function (ZIVA-4.1-PB0 : 4/5) Pin No. Symbol Description Connect to ground Non connect VSS_DAC Connect to ground for analog video DAC VSS_VIDEO Connect to ground for analog video CVBS DAC video output format : CVBS. Macrovision encoded...
Page 45
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG 4.17.6 Pin function (ZIVA-4.1-PB0 : 5/5) Pin No. Symbol Description DVD-DATA7/CDG-SCLK DVD parallel compressed data from DVD DSP. or CD-G clock indicating sub code data clock input or output VDACK In synchronous mode, bit stream data acknowledge. Asserted when DVD data is valid.
Page 46
XV-S300BK/XV-S332SL XV-S402SL/XV-S403SG VICTOR COMPANY OF JAPAN, LIMITED PERSONAL & MOBILE NETWORK BUSINESS UNIT 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan 200206 No.A0030...
Page 47
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety.
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG PARTS LIST [XV-S300BK/XV-S332SL] [XV-S402SL/XV-S403SG] * All printed circuit boards and its assemblies are not available as service parts. Area Suffix UJ ------------ U.S.A.Militaly A ------------------- Australia UB -------------- Hong Kong UG --- Turkey,South Sfrica, Egypt UP --------------------- Korea US --------------- Singapore...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Exploded view of general assembly and parts list Block No. M 28 BACK SIDE Grease UD-24H2R 27 BACK SIDE ONLY FOR XV-S300BK XV-S332SL...
Page 64
GN10017-008A FRONT PANEL XV-S332SL GN10018-003A FRONT PANEL XV-S402SL GN10018-015A FRONT PANEL XV-S403SG GN40006-001A JVC MARK XV-S300BK GN40006-002A JVC MARK except XV-S300BK GN40017-001A FELT SPACER FRONT FOOT XV-S402SL/S403SG GN20009-001A WINDOW SCREEN XV-S300BK/S332SL GN20010-002A WINDOW SCREEN XV-S402SL GN20010-003A WINDOW SCREEN XV-S403SG LE30900-001A...
Page 65
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Parts list (General assembly) Block No. M1MM Area Item PartsNo Parts name Q'ty Description GN20018-081A REAR PANEL XV-S332SL UB,US GN20018-082A REAR PANEL XV-S332SL UT GN20018-083A REAR PANEL XV-S332SL UW GN20018-085A REAR PANEL XV-S332SL A GN20018-086A REAR PANEL XV-S332SL UG...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG DVD Traverse mechanism assembly and parts list Block No. M Grease EBS0006-013B PG-641 CFD-4007ZY2 12.0mm 0.2mm 65.2mm...
Page 67
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Parts list (DVD Traverse mechanism assembly) Block No. M2MM Item Parts number Parts name Q'ty Description Area LE20520-002A MECHA BASE LE20516-001A SPINDLE BASE QYSDST2605M TAPPING SCREW LE30909-001A HOLDER QAR0165-001 FEED MOTOR LV41510-001A FEED GEAR QYSPSPU2040M SCREW LV41512-001A FEED GEAR...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Parts list (DVD Loading mechanism assembly) Block No. M3MM Item Description Parts number Parts name Q'ty Area LV10454-007A LOADING BASE QAR0164-001 MOTOR LV42087-001A MOTOR PULLEY QYSPSPU1730Z SCREW VKZ4777-003 MINI SCREW LV42209-001A BELT LV42084-002A PULLEYGEAR LV42085-002A MIDDLE GEAR LV42086-001A IDLE GEAR...
Page 70
C 934 QEZ0528-108 E CAPACITOR C 668 NCS31HJ-271X C CAPACITOR C 935 QETN1AM-477Z E CAPACITOR C 691 NCS31HJ-101X C.CAPA. C.M except XV-S300BK C 938 NCB31HK-471X C CAPACITOR C 701 QETN1HM-105Z E CAPACITOR C 939 NCB31EK-104X C CAPACITOR C 702 NCB31CK-104X C.CAPA.
Page 71
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Electrical parts list (Main board) Block No. 01 A Item PartsNo Item PartsNo PartsName Remarks Area PartsName Remarks Area C1702 QETN1EM-475Z E CAPACITOR K708 NQR0227-004X F.BEADS C.M C1703 NCS31HJ-151X C CAPACITOR K709 NQR0227-004X F.BEADS C.M C1704 NCS31HJ-331X C.CAPA. C.M...
Page 72
RES. C.M R 777 NRSA63J-101X RES. C.M R1776 NRSA63J-0R0X RES. C.M XV-S402SL/S403SG R 778 NRSA63J-103X RES. C.M S691 QSW0454-001 except XV-S300BK R 782 NRSA63J-221X MG.RES C.M S692 QSW0454-001 R 783 NRSA63J-221X MG.RES C.M S801 QSW0651-001Z TACT SWITCH R 786 NRSA63J-333X RES.I.M...
Page 73
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Electrical parts list (Servo control board) Block No. 02 Item Parts Number Parts Name Remarks Area Item Parts Number Parts Name Remarks Area NCB31CK-104X C.CAPA. C.M C263 NCB31CK-104X C.CAPA. C.M NCB31CK-104X C.CAPA. C.M C264 NCB31CK-103X C.CAPA. C.M NCB31CK-104X C.CAPA. C.M...
Page 74
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Electrical parts list (Servo control board) Block No. 02 Item Parts Number Parts Name Remarks Area Item Parts Number Parts Name Remarks Area C502 NCB31CK-104X C.CAPA. C.M IC501 ZIVA-4.1-PB0 C503 NCB31CK-104X C.CAPA. C.M IC503 74VHC00MTC-X C504 NCB31CK-104X C.CAPA. C.M...
Page 75
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Electrical parts list (Servo control board) Block No. 02 Item Parts Number Parts Name Remarks Area Item Parts Number Parts Name Remarks Area R208 NRSA63J-223X RES. C.M R411 NRSA63J-472X RES. C.M R209 NRSA63J-223X RES. C.M R413 NRSA63J-472X RES. C.M...
Page 76
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Electrical parts list (Servo control board) Block No. 02 Item Parts Number Parts Name Remarks Area Extention of area column 1: XV-S300BK UJ 13: XV-S402SL US R577 NRSA63J-470X MG.RES C.M 2: XV-S332SL A 14: XV-S402SL UT X571 NAX0550-001X CRYSTAL...
XV-S300BK/XV-S332SL/XV-S402SL/XV-S403SG Packing materials and accessories parts list Block No. M4MM Block No. M5MM Accessories Only version A,UB Only version A,UB Only XV-S300BK Except XV-S300BK 3-16...
Page 78
A 15 BT-56002-2 SVC CENTER LIST 2,10 A 16 GN30014-004A UB SHEET A 17 GN30014-005A UB SHEET Extention of area column 1: XV-S300BK UJ 7:XV-S332SL UT 13: XV-S402SL US 2: XV-S332SL A 8:XV-S332SL UW 14: XV-S402SL UT 3: XV-S332SL UB 9:XV-S332SL UX...