Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.4 2006.02
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channel-
minimum RMS power, with no more than 10%
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Sony Corporation
9-877-647-05
2006B04-1
Personal Audio Division
© 2006.02
Published by Sony Techno Create Corporation
CFD-S300
Model Name Using Similar Mechanism CFD-S250
CD
CD Mechanism Type
Section
Optical Pick-up Name
Model Name Using Similar Mechanism CFD-S250
TC
Section Tape Transport Mechanism Type
SPECIFICATIONS
Radio section
Frequency range
FM: 87.5 - 108 MHz
US, CND, E92, MX model:
AM: 530 - 1,710 kHz
AUS, KR, SP, TW model:
AM: 531 - 1,611 kHz (9 kHz step)
530 - 1,610 kHz (10 kHz step)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10,000 Hz
CD RADIO CASSETTE-CORDER
US Model
Canadian Model
E Model
Australian Model
KSM-213RDP
KSS-213R
MF-S200
– Continued on next page –
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony CFD-S300

  • Page 1 Laser diode properties 4-track 2 channel stereo Material: GaAlAs Fast winding time Wave length: 780 nm Approx. 120 sec. with Sony cassette C-60 Emission duration: Continuous Frequency response Laser output: Less than 44.6 µW TYPE I (normal): 80 - 10,000 Hz...
  • Page 2 LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    CFD-S300 Ver. 1.4 SAFETY CHECK-OUT (US MODEL) TABLE OF CONTENTS After correcting the original service problem, perform the following safety check before releasing the set to the customer: 1. SERVICING NOTES ............4 Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.
  • Page 4: Servicing Notes

    CFD-S300 SECTION 1 SERVICING NOTES LASER DIODE AND FOCUS SEARCH OPERATION CHUCK PLATE JIG ON REPAIRING CHECK 1. Turn ON the [OPERATE] button and press [CD] button to CD On repairing CD section, playing a disc without the lid (CD), use position.
  • Page 5: General

    CFD-S300 SECTION 2 GENERAL This section is extracted from instruction manual. Location of controls Remote Control Loading a CD Inserting a cassette With the side you want to play facing you POWER FUNCTION With the labeled side up BAND .,>...
  • Page 6: Disassembly

    CFD-S300 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. 3-1. CABINET TOP ASSY (Page 7) 3-2. CABINET FRONT ASSY, 3-9. CD LID 3-10. CD BLOCK ASSY CABINET BOTTOM ASSY (Page 11) (Page 11) (Page 7) 3-11.
  • Page 7: Cabinet Top Assy

    CFD-S300 Note : Follow the disassembly procedure in the numerical order given. 3-1. CABINET TOP ASSY 3 two screws 4 two screws (+BV (B2.6 ) ) (+BV (B2.6 ) ) 5 three screws (+BV (B2.6 ) ) CD lid handle...
  • Page 8: Wires

    CFD-S300 3-3. WIRES Put flat cable and wires between the cabinets and push them in the grooves located at A to G in the figure to prevent disconnection before assembling the set. from H/P board cabinet front cabinet bottom 3-4. MD BLOCK 1 two screws (+P (B2.6 ) )
  • Page 9: Cassette Holder

    CFD-S300 3-5. CASSETTE HOLDER 1 screw 2 damper (+BV (B2.6 ) ) two claws 4 cassette spring two claws 3 cassette holder 3-6. MAIN BOARD 5 screw (+BV (B2.6 ) ) 6 screw (+BV (B2.6 ) ) 7 MAIN board...
  • Page 10: Tuner Board

    CFD-S300 3-7. TUNER BOARD 2 telescopic antenna 1 screw (+P (M3 ) ) 3 screw (+BV (B2.6 ) ) 6 TUNER board 4 two claws 3-8. POWER BOARD 2 two screws (+BV (B2.6 ) ) 3 two screws (+BV (B2.6 ) )
  • Page 11: Cd Lid

    CFD-S300 3-9. CD LID 3 CD lid 2 two claws CD spring 1 two claws 3-10. CD BLOCK ASSY 3 CD cover two claws two claws 4 CD block assy 2 two screws 1 two screws (+PWH 2.6 x 10)
  • Page 12: Optical Pick-Up

    CFD-S300 3-11. OPTICAL PICK-UP 6 optical pick-up 5 sled shaft claw 1 gear (A) 2 screw PWB tapping (M2) 3 screw PWB tapping (M2) 3-12. R/P HEAD (HRP301), TC BOARD 6 Remove the four solderings. 1 two claws 3 screw...
  • Page 13: Motor Assy (M801), Main Belt (B), Sub Belt (B)

    CFD-S300 3-13. MOTOR ASSY (M801), MAIN BELT (B), SUB BELT (B) 1 screw (+BVTT 2 x 4) 9 motor assy (M801) 2 protect chassis motor bracket 6 main belt (B) 3 screw bind DT M2 x 6 4 screw bind DT M2 x 6 8 two screws pan M2.6 x 4.5...
  • Page 14: Mechanical Adjustments

    CFD-S300 SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION TAPE SECTION 0 dB = 0.775 V 1. Clean the following parts with a denatured-alcohol-moistened swab : • Standard Output Level record/playback head pinch roller Output terminal HP OUT erase head rubber belts 32 Ω...
  • Page 15: Tuner Section

    CFD-S300 TUNER SECTION 0 dB = 1 µV AM IF ADJUSTMENT • AM Section Adjust for a maximum reading on level meter. Setting: RADIO BAND•AUTO PRESET button: AM 450 kHz AM RF signal generator AM FREQUENCY COVERAGE Put the lead-wire...
  • Page 16: Cd Section

    CFD-S300 Adjustment Location: CT3, L3 TRACKING ADJUSTMENT – MAIN board (component side) – TP (VT) (CONDUCTOR SIDE) CT1, L1 TP (FM IN) TRACKING (CONDUCTOR SIDE) ADJUSTMENT ADJUSTMENT FREQUENCY COVERAGE ADJUSTMENT ADJUSTMENT FREQUENCY COVERAGE ADJUSTMENT CD SECTION CD section adjustments are done automatically in this set.
  • Page 17: Diagrams

    CFD-S300 SECTION 6 DIAGRAMS 6-1. IC PIN DESCRIPTION • IC802 uPD789477GC-A35-8BT (SYSTEM CONTROLLER) Pin No. Pin Name Pin Description Pin No. Pin Name Pin Description 1, 2 — Not used. (Open) Main system oscillation output (4.19 MHz) 3 to 5...
  • Page 18: Block Diagram - Cd Section

    CFD-S300 6-3. BLOCK DIAGRAM — CD SECTION — LCHO INTERPOLATION CD_IN_ L SLICE ERROR MUTE DIGITAL FIN2 EFMIN (Page 19) LEVEL CORRECTION & FILTER CONTROL AUDIO CD ATTENUATION & RCHO CD_IN_R DEEMPHASIS 1-bit DAC PH/BH AUDIO DOUT FIN1 CLV,CAV RF AMP,...
  • Page 19: Block Diagram - Main Section

    CFD-S300 6-4. BLOCK DIAGRAM — MAIN SECTION — IC302 R.RO ELECTRONIC VOLUME R.IN R.LINE POWER AMP REC/PB CD_IN_R IC304 PRE AMP R-CH (Page 18) L.RO IC301 VOL AMP J321 ALC 2 L-OUT L.LINE LINE AMP L-IN L.LO CD_IN_L Q113 HRP301...
  • Page 20: Printed Wiring Board - Cd Section

    CFD-S300 Ver 1.1 : Uses unleaded solder. 6-5. PRINTED WIRING BOARD — CD SECTION — • Refer to page 17 for Circuit Boards Location. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
  • Page 21: Schematic Diagram - Cd Section

    CFD-S300 6-6. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 20 for Common Note on Schematic Diagrams and page 33 for IC Block Diagrams. C727 C726 C724 C725 C721 R717 C730 R716 C720 R728 R727 R718 C722 (Page 25)
  • Page 22: Printed Wiring Board - Tuner Section

    CFD-S300 Ver 1.1 : Uses unleaded solder. 6-7. PRINTED WIRING BOARD — TUNER SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. (Page 24) (Page 24) 1-688-455- (11) •...
  • Page 23: Schematic Diagram - Tuner Section

    CFD-S300 Ver 1.1 6-8. SCHEMATIC DIAGRAM — TUNER SECTION — • Refer to page 20 for Common Note on Schematic Diagrams and page 34 for IC Block Diagrams. JC12 JC11 JC24 IC B/D IC B/D JC13 ANT1 CNP2 CNP1 (Page 25)
  • Page 24: Printed Wiring Boards - Main Section

    CFD-S300 6-9. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder. JW850 C323 R245 JW875 JW858 C112 JW860 KH301...
  • Page 25: Schematic Diagram - Main Section (1/2)

    CFD-S300 Ver 1.1 6-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 20 for Common Note on Schematic Diagrams, page 24 for Waveforms and page 35 for IC Block Diagrams. R832 R835 R844 R839 TP803 R836 TP802...
  • Page 26: Schematic Diagram - Main Section (2/2)

    CFD-S300 6-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 20 for Common Note on Schematic Diagrams and page 35 for IC Block Diagrams. R145 D323 C323 R323 R324 C324 R245 R134 C129 C115 R133 R131 R135...
  • Page 27: Printed Wiring Board - Tc Section

    CFD-S300 6-12. PRINTED WIRING BOARD — TC SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder. T301 C308 C307 C310 C305 R307 R308 C304...
  • Page 28: Schematic Diagram - Tc Section

    CFD-S300 6-13. SCHEMATIC DIAGRAM — TC SECTION — • Refer to page 20 for Common Note on Schematic Diagrams and page 35 for IC Block Diagrams. IC301 IC B/D R103 R112 R301 C102 R102 C103 R104 R111 C301 C104 C101...
  • Page 29: Printed Wiring Boards - Control Section

    CFD-S300 6-14. PRINTED WIRING BOARDS — CONTROL SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder. S411 R413 S410 S428 S409 (Page 24) S426...
  • Page 30: Schematic Diagram - Control Section

    CFD-S300 6-15. SCHEMATIC DIAGRAM — CONTROL SECTION — • Refer to page 20 for Common Note on Schematic Diagrams. (Page 25) D405 CNP401 R443 R444 IC401 R448 R438 R437 R447 C405 R459 S417 C406 JC401 R458 S438 R434 S418 R435...
  • Page 31: Printed Wiring Boards - Power Supply Section

    CFD-S300 6-16. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 17 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder. (Page 24) JW904 CNB901...
  • Page 32: Schematic Diagram - Power Supply Section

    CFD-S300 Ver 1.1 6-17. SCHEMATIC DIAGRAM — POWER SUPPLY SECTION — • Refer to page 20 for Common Note on Schematic Diagrams. (Page 26)
  • Page 33: Ic Block Diagrams

    CFD-S300 6-18. IC BLOCK DIAGRAMS IC701 LC78646E-E (CD Board) 78 77 76 75 74 73 72 71 69 68 67 66 65 64 63 62 61 FIN1 – FIN2 – TIN1 TBAL – – TIN2 – – TBAL – RFMON...
  • Page 34 CFD-S300 IC702 BA5826FP-E2 (CD Board) IC1 TA2149BN (TUNER Board) GND1 FM RF-OUT FM RF SP– D.BUFF VCC1 FM RF-IN SL– AM RF-IN D.BUFF AM LOW CUT LEVEL D.BUFF SHIFT MIX OUT FM OSC D.BUFF SPIN LEVEL SHIFT AM OSC BUFF...
  • Page 35 CFD-S300 IC803 CAT24WC02JI-1.8-TE13 (MAIN Board (1/2)) 1K BIT EEPROM ARRAY 8BIT 7BIT SLAVE • WORD ADDRESS DATA ADDRESS 7BIT DECODER REGISTER REGISTER START STOP CONTROL CIRCUIT HIGH VOLTAGE POWER SUPPLY OCCURENCE CIRCUIT VOLTAGE DETECTION IC302 PT2257 (MAIN Board (2/2)) L-IN...
  • Page 36: Exploded Views

    CFD-S300 Ver 1.1 SECTION 7 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied.
  • Page 37: Cabinet (Front) Section

    CFD-S300 Ver 1.1 7-2. CABINET (FRONT) SECTION SP301 MF-S200 SP302 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3384-657-1 CABINET (FRONT) SUB ASSY (S) 3-261-984-01 BUTTON, FF (AUS,KR,SP,TW) (SILVER)...(SILVER) (EXCEPT US,AUS) 3-261-984-11 BUTTON, FF (US,CND,E92,MX) X-3384-660-1 CABINET (FRONT) SUB ASSY (L) 3-261-983-01 BUTTON, REW (AUS,KR,SP,TW) (BLUE)...(BLUE) (E92,KR,SP,TW)
  • Page 38: Cabinet (Top) (1) Section

    CFD-S300 Ver 1.1 7-3. CABINET (TOP) (1) SECTION S801 KSM-213RDP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-923-736-01 COVER, CD 1-452-899-11 MAGNET 3-931-379-31 RUBBER, VIBRATION PROOF 3-261-989-21 LID, CD (SILVER)...(SILVER) 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING 3-261-989-31 LID, CD (BLUE)...(BLUE)
  • Page 39: Cabinet (Top) (2) Section

    CFD-S300 Ver. 1.3 7-4. CABINET (TOP) (2) SECTION LCD401 not supplied (FUNCTION BUTTON board) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3385-052-1 CABINET (TOP) SUB ASSY (S) 1-829-063-11 CABLE, FLEXIBLE FLAT (21 CORE) (SILVER)...(SILVER) (AUS,KR,SP,TW)
  • Page 40: Cabinet (Bottom) Section

    CFD-S300 Ver 1.1 7-5. CABINET (BOTTOM) SECTION ANT1 T901 not supplied F902 not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety.
  • Page 41: Tape Mechanism Section

    CFD-S300 7-6. TAPE MECHANISM SECTION M801 not supplied not supplied not supplied HRP301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-237-718-01 LEVER, REC 3-244-083-01 +SCREW BIND DT M2X6 * 252 A-3683-864-A TC BOARD, COMPLETE * 259...
  • Page 42: Cd Mechanism Section

    CFD-S300 7-7. CD MECHANISM SECTION (KSM-213RDP) (including M701) M702 The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce...
  • Page 43: Electrical Parts List

    CFD-S300 Ver 1.1 SECTION 8 BATTERY (1) ELECTRICAL PARTS LIST BATTERY (2) NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 44 CFD-S300 CD BUTTON CONNECTOR FUNCTION BUTTON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R704 1-216-833-11 METAL CHIP 1/10W < RESISTOR > R705 1-216-833-11 METAL CHIP 1/10W R706 1-216-841-11 METAL CHIP 1/10W R450 1-216-821-11 METAL CHIP...
  • Page 45 CFD-S300 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > S418 1-786-050-21 SWITCH, KEYBOARD (5) S419 1-786-050-21 SWITCH, KEYBOARD (4) R146 1-216-809-11 METAL CHIP 1/10W S420 1-786-050-21 SWITCH, KEYBOARD (3) R246...
  • Page 46 CFD-S300 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C800 1-164-156-11 CERAMIC CHIP 0.1uF IC803 6-700-336-01 IC CAT24WC02JI-1.8-TE13 C801 1-162-974-11 CERAMIC CHIP 0.01uF IC804 6-703-224-01 IC S-80828CNNB-B8NT2G C802 1-104-658-11 ELECT 100uF C803 1-162-927-11 CERAMIC CHIP 100PF <...
  • Page 47 CFD-S300 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R232 1-216-821-11 METAL CHIP 1/10W R821 1-216-829-11 METAL CHIP 4.7K 1/10W R233 1-216-825-11 METAL CHIP 2.2K 1/10W R822 1-216-817-11 METAL CHIP 1/10W R234 1-216-817-11 METAL CHIP...
  • Page 48 CFD-S300 Ver 1.1 MAIN POWER POWER BUTTON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R881 1-216-833-11 METAL CHIP 1/10W < DIODE > R882 1-216-833-11 METAL CHIP 1/10W R883 1-216-833-11 METAL CHIP 1/10W D901 8-719-063-79 DIODE 1N4002B...
  • Page 49 CFD-S300 Ver 1.1 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C310 1-164-230-11 CERAMIC CHIP 220PF < SWITCH > < CONNECTOR > S301 1-786-126-11 SWITCH, SLIDE (REC/PB) CN303 1-784-774-11 CONNECTOR, FFC 13P < TRANSFORMER >...
  • Page 50 CFD-S300 Ver 1.1 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-964-11 CERAMIC CHIP 0.001uF 1-414-142-11 INDUCTOR 1uH (US,CND,E92,MX) 1-162-964-11 CERAMIC CHIP 0.001uF 1-410-509-11 INDUCTOR 10uH 1-162-927-11 CERAMIC CHIP 100PF 1-162-964-11 CERAMIC CHIP 0.001uF < RESISTOR >...
  • Page 51 CFD-S300 Ver 1.1 Ref. No. Part No. Description Remark MISCELLANEOUS *************** 1-757-689-11 CABLE, FLEXIBLE FLAT (16 CORE) 1-452-899-11 MAGNET 1-829-068-11 CABLE, FLEXIBLE FLAT (14 CORE) 1-829-062-11 CABLE, FLEXIBLE FLAT (4 CORE) 1-829-067-11 CABLE, FLEXIBLE FLAT (8 CORE) 1-829-063-11 CABLE, FLEXIBLE FLAT (21 CORE)
  • Page 52 CFD-S300 MEMO...
  • Page 53 CFD-S300 US Model Canadian Model SERVICE MANUAL E Model Australian Model Ver 1.2 2004. 09 SUPPLEMENT-1 File this supplement with the service manual. Subject: Change of CD Mechanism Block (KSM-213RDP→KSM-213CDP) (SPM-04041) CD mechanism block is changed from KSM-213RDP to KSM-213CDP in the midway of production.
  • Page 54 CFD-S300 CD MECHANISM SECTION (KSM-213CDP) not supplied not supplied (M701 (SPINDLE)) M702 The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité.
  • Page 55 CFD-S300 MEMO...
  • Page 56 CFD-S300 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.02 2004.04...

Table of Contents